Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 

SONET/SDH OC192/STM64 PICs with XFP (T1600 Router)

 
Figure 1: 1-Port SONET/SDH OC192/STM64 PIC
1-Port SONET/SDH OC192/STM64 PIC
Figure 2: 4-Port SONET/SDH OC192/STM64 PIC
4-Port SONET/SDH OC192/STM64 PIC

Software release

  • 1-port: Junos OS Release 8.5 and later (Type 3)

  • 4-port: Junos OS Release 8.5 and later (Type 4)

For information on which FPCs support this PIC, see T1600 PIC/FPC Compatibility.

Description

  • One or four OC192 ports

  • 4-port OC192 PIC with XFP: four OC192 links can be aggregated into one OC768 link or two OC256 links. The four fiber links should be on the same fiber path or the same fiber.

  • Power requirement:

    • 1-port: 0.52 A @ 48 V (25 W)

    • 4-port: 1.11 A @ 48 V (53.1 W)

  • Model number: PC-1OC192-SON-XFP

Hardware features

  • Multiplexing and demultiplexing

  • Rate policing on input

  • Rate shaping on output

  • Packet buffering, Layer 2 parsing

Software features

  • Configuration of SONET or SDH framing on a per-port basis on the 4-port Type 4 PIC

  • SONET/SDH framing

  • Link aggregation

  • Alarm and event counting and detection

  • Dual-router automatic protection switching (APS)

  • Multiprotocol Label Switching (MPLS) fast reroute

  • Encapsulations:

    • Circuit cross-connect (CCC)

    • Translational cross-connect (TCC)

    • Frame Relay

    • High-Level Data Link Control (HDLC)

    • Point-to-Point Protocol (PPP)

Cables and connectors

  • Duplex LC connector (Rx and Tx)

  • SONET/SDH OC192c/STM64 XFP transceivers:

    • Short reach (SR-1) (model number: XFP-10G-L-OC192-SR1)

    • Intermediate reach (IR-1) (model number: XFP-10G-E-OC192-IR2)

    • Long reach (LR-1) (model number: XFP-10G-Z-OC192-LR2)

    Optical interface specifications—see SONET/SDH OC192/STM64 Optical Interface Specifications

Note: To extend the life of the laser, when a PIC is not being actively used with any valid links, take the PIC offline until you are ready to establish a link to another device. For information about taking a PIC offline, see the request chassis pic offline command in the CLI Explorer.

LEDs

One tricolor LED per port:

  • Off—Not enabled

  • Green—Online with no alarms or failures

  • Yellow—Online with alarms for remote failures

  • Red—Active with a local alarm; router has detected a failure

One 768 over 192 LED:

  • Off—Not enabled

  • Green—Online with no alarms or failures

  • Yellow—Online with alarms for remote failures

  • Red—Active with a local alarm; router has detected a failure

Alarms, errors, and events

  • SONET alarms:

    • Alarm indication signal—line (AIS-L)

    • Alarm indication signal—path (AIS-P)

    • Bit error rate—signal degrade (BERR-SD)

    • Bit error rate—signal fail (BERR-SF)

    • Bit interleaved parity (BIP) error B1, B2, B3

    • Far-end bit error: remote error indication—line (REI-L), far-end line coding violations (CV-LFE)

    • Far-end bit error: remote error indication—path (REI-P), far-end path coding violations (CV-PFE)

    • Loss of frame (LOF)

    • Loss of pointer (LOP-P)

    • Loss of signal (LOS)

    • Payload label mismatch (PLM-P)

    • Payload unequipped (unequipped STS at path level) (UNEQ-P)

    • Remote defect indication—line (RDI-L)

    • Remote defect indication—path (RDI-P)

  • SDH alarms:

    • Administrative unit alarm indication signal (AU-AIS)

    • Bit error rate signal degrade (BERR-SD)

    • Bit error rate signal fail (BERR-SF)

    • Bit interleaved parity (BIP) error B1, B2, B3

    • Higher order path—payload label mismatch (HP-PLM)

    • Higher order path—loss of pointer (HP-LOP)

    • Higher order path—remote defect indication (HP-RDI)

    • Higher order path—unequipped (HP-UNEQ)

    • Loss of frame (LOF)

    • Loss of signal (LOS)

    • Multiplex section—alarm indication signal (MS-AIS)

    • Multiplex section—remote defect indication (MS-RDI)

    • Multiplex section—remote error indication (MS-REI)

  • Error detection:

    • Errored seconds (ES-S, ES-L, ES-P)

    • Far-end errored seconds (ES-LFE, ES-PFE)

    • Far-end severely errored seconds (SES-LFE, SES-PFE)

    • Far-end unavailable seconds (UAS-LFE, UAS-PFE)

    • Severely errored framing (SEF)

    • Severely errored framing seconds (SEFS-S)

    • Severely errored seconds (SES-S, SES-L, SES-P)

    • Unavailable seconds (UAS-L, UAS-P)