Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 

ATM2 OC3/STM1 IQ PIC (T1600 Router)

 

Software release

Description

  • Two OC3 ports

  • Power requirement: 0.41 A @ 48 V (20 W)

  • Fine-grained queuing per logical interface

  • Conforms to ANSI T1.105-1991 and T1E1.2/93-020R1

  • ATM and SONET/SDH standards compliant

  • Alarm and event counting and detection

  • Compatible with well-known ATM switches

  • ATM switch ID, which displays the switch IP address and local interface name of the adjacent Fore ATM switches

  • Model number: PB-2OC3-ATM2-MM

    Model number: PB-2OC3-STM2-SMIR

Hardware features

  • Single 3010 SAR for segmentation and reassembly into 53 byte ATM cells

  • High-performance parsing of SONET/SDH frames

  • ASIC-based packet segmentation and reassembly (SAR) management and output port queuing

  • 64 MB SDRAM memory for ATM SAR

  • Packet buffering, Layer 2 parsing

Software features

  • Circuit cross-connect (CCC) for leveraging ATM access networks

  • User-configurable virtual circuit (VC) and virtual path (VP) support

  • Support for idle cell or unassigned cell transmission

  • OAM fault management processes alarm indication signal (AIS), remote defect indication (RDI) cells, and loop cells

  • Point-to-point and point-to-multipoint mode Layer 2 counters per VC and per VP

  • Local and remote loopback

  • ATM Inverse Address Resolution Protocol (ARP), which enables routers to automatically learn the IP address of the router on the far end of an ATM permanent virtual circuit (PVC)

  • Simple Network Management Protocol (SNMP):

    • Management Information Base (MIB) 2 (RFC 1213)

    • ATM MIB (RFC 1695)

    • SONET MIB

  • Unspecified bit rate (UBR), non-real-time variable bit rate (VBR), and constant bit rate (CBR) traffic shaping

  • Per-VC or per-VP traffic shaping

  • Support for F4 OAM cells

  • Support for 16 bit VCI range

Cables and connectors

LEDs

One tricolor per port:

  • Off—Not enabled

  • Green—Online with no alarms or failures

  • Yellow—Online with alarms for remote failures

  • Red—Active with a local alarm; router has detected a failure

Alarms, errors, and events

  • Alarm indication signal—line (AIS-L)

  • Alarm indication signal—path (AIS-P)

  • Bit error rate—signal degrade (BERR-SD)

  • Bit error rate—signal fail (BERR-SF)

  • Loss of cell delineation (LOC)

  • Loss of frame (LOF)

  • Loss of pointer (LOP-P)

  • Loss of signal (LOS)

  • Payload mismatch (PLM-P)

  • Payload unequipped (unequipped STS at path level) (UNEQ-P)

  • Remote defect indication—line (RDI-L)

  • Remote defect indication—path (RDI-P)

  • Error detection:

    • Bit interleaved parity errors B1, B2, B3

    • Errored seconds (ES-S, ES-L, ES-P)

    • Far-end bit errors, remote error indication—line (REI-L), far-end line coding violations (CV-LFE)

    • Far-end bit errors, remote error indication—path (REI-P), far-end path coding violations (CV-PFE)

    • Far-end errored seconds (ES-LFE, ES-PFE)

    • Far-end severely errored seconds (SES-LFE, SES-PFE)

    • Far-end unavailable seconds (UAS-LFE, UAS-PFE)

    • Severely errored framing (SEF)

    • Severely errored framing seconds (SEFS-S)

    • Severely errored seconds (SES-S, SES-L, SES-P)

    • Unavailable seconds (UAS-L, UAS-P)