100-Gigabit Ethernet OTN PIC with CFP2 (PTX Series)

 

Software Release

  • PTX3000: Junos OS Release 15.1F6, Junos OS Release 16.1R2 and later, Junos OS Release 17.1R1 and later

  • PTX5000: Junos OS Release 14.1R2 and later

For information about which FPCs support this PIC, see PTX Series PIC/FPC Compatibility.

Hardware Features

  • Four ports that can be configured as 100-Gigabit Ethernet, 100-Gigabit OTN, or a combination of 100-Gigabit Ethernet and 100-Gigabit Ethernet OTN interfaces.

  • Model number: P2-100GE-OTN

  • Name in the CLI: 4x100GE OTN CFP2

  • Power requirements: 14.50A@ –12 V (176 W)

  • Large maximum transmission units (MTUs): up to 9500 bytes

Software Features

Table 1 shows the first supported release for each software feature.

Table 1: Software Features Supported

Software Feature

First Supported Junos OS Release on PTX3000

First Supported Junos OS Release on PTX5000

Flexible Ethernet services encapsulation

15.1F6

16.1R2

17.1R1

14.1R2

Flexible VLAN tagging

15.1F6

16.1R2

17.1R1

14.1R2

IFINFO / IFMON

15.1F6

16.1R2

17.1R1

14.1R2

IEEE 802.1 ag OAM

15.1F6

16.1R2

17.1R1

14.1R2

IEEE 802.3 ah OAM

15.1F6

16.1R2

17.1R1

14.1R2

IEEE 802.3ad link aggregation

15.1F6

16.1R2

17.1R1

14.1R2

Interrupt-driven link-down detection for MPLS FRR

15.1F6

16.1R2

17.1R1

14.1R2

MAC accounting per logical interface for source addresses

15.1F6

16.1R2

17.1R1

14.1R2

MAC filter per port for destination addresses and source addresses

15.1F6

16.1R2

17.1R1

14.1R2

MAC filter per logical interface for source addresses

15.1F6

16.1R2

17.1R1

14.1R2

SNMP

15.1F6

16.1R2

17.1R1

14.1R2

Up to 4000 logical interfaces shared across all ports on a single PFE

15.1F6

16.1R2

17.1R1

14.1R2

Cables and Connectors

Tip

You can use the Hardware Compatibility Tool to find information about the pluggable transceivers supported on your Juniper Networks device.

The following transceivers are supported on this PIC:

  • CFP2-100G-LR4-D—Supports both 100GBASE-LR4 and OTU4 4I1-9D1F

  • CFP2-100G-SR10-D—Supports 100GBASE-SR10

    Note

    This transceiver supports Ethernet only, OTN is not supported.

  • CFP2-100GBASE-LR4—Supports 100GBASE-LR4

  • CFP2-100GBASE-SR10—Supports 100GBASE-SR10

  • CFP2-100GBASE-SR10-D2—Supports 100GBASE-SR10

    Note

    This dual rate transceiver is supported in Junos OS 14.2R5 release.

  • CFP2-100GBASE-ER4—Supports 100GBASE-ER4

  • CFP2-DCO-T-WDM-1—Supports 100GBASE-LR4

    Note

    CFP2-DCO-T-WDM-1 is not NEBS compliant on the P2-100GE-OTN PIC. It can only work with an ambient temperature of up to 104° F (40° C) at altitudes up to 6,000 ft (1829 m).

LEDs

The STATUS LED is located to the left of the ONLINE/OFFLINE button. One LED is located next to each port to indicate the link activity of the port. Table 2 describes the functions of these LEDs.

Table 2: 100-Gigabit Ethernet OTN PIC with CFP2 LEDs

Label

Color

State

Description

STATUS

Green

On steadily

PIC is online with no alarms or failures.

Yellow

On steadily

PIC is initializing.

Red

On steadily

PIC is in failed state.

Off

PIC is offline or not enabled.

Single LED per port, labeled 0, 1, 2, and 3

Green

On steadily

Port is online with no alarms or failures, and the link is up.

Blinking

Activity detected. Port is sending or receiving packets.

Red

On steadily

Port is on but the link is down, and the port has detected a failure with alarms.

Off

Port is off or not enabled.