Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

10-Gigabit Ethernet/40-Gigabit Ethernet LAN/WAN OTN PIC with QSFP+ (PTX Series)

 

Software Release

  • PTX3000: Junos OS Release 15.1F6, Junos OS Release 16.1R2 and later, Junos OS Release 17.1R1 and later

  • PTX5000: Junos OS Release 14.1R2 and later

For information about which FPCs support these PICs, see PTX Series PIC/FPC Compatibility.

Hardware Features

  • Twelve ports (0 through 11) configurable as either 10-Gigabit Ethernet ports (in LAN, WAN, or OTU2) or 40-Gigabit Ethernet ports (in Ethernet or OTU3).

    Note

    The PIC supports either 10-Gigabit Ethernet or 40-Gigabit Ethernet ports. You cannot configure both 10-Gigabit Ethernet and 40-Gigabit Ethernet ports on the same PIC. You can, however, have PICs with 10-Gigabit Ethernet and 40-Gigabit Ethernet ports in the same FPC.

  • Model number: P2-10G-40G-QSFPP

  • Name in the CLI: 48x10G/12x40G(LWO)QSFP+

  • Independent per-port configuration of:

    • LAN-PHY, WAN-PHY, or OTN framing for ports configured in 10-Gigabit Ethernet mode

    • LAN/WAN or OTN framing for 40-Gigabit Ethernet mode

  • Power requirements:

    • 10-Gigabit Ethernet LAN/WAN mode (with QSFP+ transceivers on all ports)—9.09 A @–12.1 V (110 W)

    • 40-Gigabit Ethernet LAN mode (with QSFP+ on all ports)—8.26 A @–12.1 V (100 W)

  • High-performance throughput:

    • 10-Gigabit Ethernet LAN mode at 10.3 Gbps

    • 10-Gigabit Ethernet WAN mode at 9.9 Gbps

    • 40-Gigabit Ethernet LAN mode at 41.2 Gbps (10.3 Gbps per lane)

  • Configurable modes:

    • LAN-PHY—10-Gigabit Ethernet and 40-Gigabit Ethernet

    • WAN-PHY—10-Gigabit Ethernet

  • Full-duplex mode

  • Large maximum transmission units (MTUs): up to 9192 bytes

Software Features

Table 1 shows the first supported Junos OS release for each software feature.

Table 1: Software Features Supported

Software Feature

PTX3000 First Supported Junos OS Release

PTX5000 First Supported Junos OS Release

Flexible-ethernet-services encapsulation

15.1F6

16.1R2

17.1R1

14.1R2

Flexible VLAN tagging

15.1F6

16.1R2

17.1R1

14.1R2

IFINFO / IFMON

15.1F6

16.1R2

17.1R1

14.1R2

IEEE 802.1 ag OAM

15.1F6

16.1R2

17.1R1

14.1R2

IEEE 802.3 ah OAM

15.1F6

16.1R2

17.1R1

14.1R2

IEEE 802.3ad link aggregation

15.1F6

16.1R2

17.1R1

14.1R2

Interrupt-driven link-down detection for MPLS FRR

15.1F6

16.1R2

17.1R1

14.1R2

MAC accounting per logical interface for source addresses

15.1F6

16.1R2

17.1R1

14.1R2

MAC filter per port for destination addresses and source addresses

15.1F6

16.1R2

17.1R1

14.1R2

MAC filter per logical interface for source addresses

15.1F6

16.1R2

17.1R1

14.1R2

SNMP

15.1F6

16.1R2

17.1R1

14.1R2

Up to 8000 logical interfaces share across all ports on a single Packet Forwarding Engine

15.1F6

16.1R2

17.1R1

14.1R2

Cables and Connectors

Tip

You can use the Hardware Compatibility Tool to find information about the pluggable transceivers supported on your Juniper Networks device.

LEDs

The STATUS LED is located next to the ONLINE/OFFLINE button. The port LEDs are grouped into 12 and each group has four LEDs labeled 0, 1, 2, and 3. The groups have labels 0 through 11. The LEDs located next to each port indicate the link, status, and alarms, if any. Table 2 describes the functions of these LEDs.

Note

If the PIC is configured for 40-Gigabit Ethernet, only the LED labeled 0 in a group of LEDs is lit and if the PIC is configured for 10-Gigabit Ethernet, then all four LEDs in a group are lit. You can use the following command to change the mode:

[edit chassis]

user@host# set fpc fpc-slot pic pic-slot pic-mode (10G | 40G)

Table 2: 10-Gigabit Ethernet/40-Gigabit Ethernet LAN/WAN OTN PIC with QSFP+ LEDs

Label

Color

State

Description

STATUS

Green

On steadily

PIC is online with no alarms or failures.

Yellow

On steadily

PIC is initializing.

Red

On steadily

PIC has an error or failure.

Off

PIC is offline and safe to remove from the router.

LEDs 0 through 11 and each group of LEDs are labeled 0, 1, 2, and 3.

Green

On steadily

Port is online with no alarms or errors, and the link is up

Blinking

There is link activity on the port.

Red

On steadily

Port is on but the link is down, and the port has detected a failure.

Off

Port is off or not enabled.