Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 

Channelized OC48/STM16 Enhanced IQ (IQE) EOL PIC with SFP (M120 Router)

 

Software release

Description

  • One OC48/STM16 port

  • SONET or SDH is configurable on a per-port granularity

  • Channelization: OC12, OC3, DS3, DS1, DS0, E3, E1

  • SONET channelization:

    • 4 OC12 channel

    • 16 OC3 channels

    • 48 DS3 channels

    • 672 DS1 channels

    • 975 DS0 channels

  • SDH channelization:

    • 4 STM4 channel

    • 16 STM1 channels

    • 48 E3 channels

    • 504 E1 channels

    • 975 DS0 channels

  • Power requirement: 1.10 A @ 48V (53 W)

  • Model number: PB-1CHOC48-STM16-IQE-SFP

Hardware features

  • Port is numbered 0.

Software features

  • Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED)

  • Enhanced fine-grained queuing per logical interface. See the Class of Service Feature Guide for Routing Devices and EX9200 Switches for more information about class of service features.

  • Subrate and scrambling:

    • Digital Link/Quick Eagle

    • Kentrox

    • Larscom

    • ADTRAN

    • Verilink

  • Packet buffering, Layer 2 parsing

  • M13/C-bit parity encoding

  • DS3 far-end alarm and control (FEAC) channel support

  • Local line, remote line, and remote payload loopback testing

  • Simple Network Management Protocol (SNMP): OC12, OC3 MIB, DS3 MIB, T1 MIB

  • Dynamic, arbitrary channel configuration

  • Full bit error rate test (BERT)

  • Encapsulations:

    • Circuit cross-connect (CCC)

    • Translational cross-connect (TCC)

    • Extended Frame Relay for CCC and TCC

    • Flexible Frame Relay

    • Frame Relay

    • Frame Relay for CCC

    • Frame Relay for TCC

    • Frame Relay port CCC

    • High-Level Data Link Control (HDLC)

    • HDLC framing for CCC

    • HDLC framing for TCC

    • MPLS CCC

    • MPLS TCC

    • Multilink Frame Relay (MLFR) UNI NNI (MFR FRF.16)

    • Point-to-Point Protocol (PPP)

    • PPP for CCC

    • PPP for TCC

  • Encapsulations available only for DS1:

    • Multilink Frame Relay end-to-end (MLFR FRF.15)

    • Multilink PPP (MLPPP)

    • PPP over Frame Relay

Cables and connectors

  • Duplex LC/PC connector (Rx and Tx); single-mode fiber

  • SONET/SDH OC48/STM16 SFPs:

    • Short reach (SR-1) (model number: SFP-1OC48-SR)

    • Intermediate reach (IR-1) (model number: SFP-1OC48-IR)

    • Long reach (LR-1) (model number: SFP-1OC48-LR)

    Optical interface specifications—see SONET/SDH OC48/STM16 Optical Interface Specifications

LEDs

One tricolor per port:

  • Off—Not enabled

  • Green—Online with no alarms or failures

  • Yellow—Online with alarms for remote failures

  • Red—Active with a local alarm; router has detected a failure

Alarms, errors, and events

  • SONET alarms:

    • Alarm indication signal—line (AIS-L)

    • Alarm indication signal—path (AIS-P)

    • Bit error rate—signal degrade (BERR-SD)

    • Bit error rate—signal fail (BERR-SF)

    • Loss of frame (LOF)

    • Loss of light (LOL)

    • Loss of pointer (LOP)

    • Loss of signal (LOS)

    • Payload label mismatch (PLM-P)

    • Remote defect indication—line (RDI-L)

    • Remote defect indication—path (RDI-P)

    • Remote error indication (REI)

    • Payload unequipped (unequipped STS at path level) (UNEQ-P)

    • Virtual container—alarm indication signal (VAIS)

    • Virtual container—loss of pointer (VLOP)

    • Virtual container—mismatch (VMIS)

    • Virtual container—remote defect indication (VRD1)

    • Virtual container—unequipped (VUNEQ)

  • SDH alarms:

    • Administrative unit alarm indication signal (AU-AIS)

    • Bit error rate—signal degrade (BERR-SD)

    • Bit error rate—signal fail (BERR-SF)

    • Bit interleaved parity (BIP) error B1, B2, B3

    • Higher order path—alarm indication signal (HP-AIS)

    • Higher order path—far-end receive failure (HP-FERF)

    • Higher order path—payload label mismatch (HP-PLM)

    • Higher order path—loss of pointer (HP-LOP)

    • Higher order path—remote defect indication (HP-RDI)

    • Higher order path—unequipped (HP-UNEQ)

    • Loss of frame (LOF)

    • Loss of light (LOL)

    • Loss of signal (LOS)

    • Multiplex section—alarm indication signal (MS-AIS)

    • Multiplex section—far-end receive failure (MS-FERF)

    • Multiplex section—remote defect indication (MS-RDI)

    • Multiplex section—remote error indication (MS-REI)

    • Phase lock loop (PLL)

    • Remote error indication (REI)

    • Severely errored frame (SEF)

    • Tributary unit—alarm indication signal (TU-AIS)

    • Tributary unit—loss of pointer (TU-LOP)

    • Tributary unit—mismatch (TU-MIS)

    • Tributary unit—remote defect indication (TU-RD1)

    • Tributary unit—unequipped (TU-UNEQ)

  • DS1 alarms:

    • Alarm indication signal (AIS)

    • Loss of frame (LOF)

    • Remote alarm indication signal (RAIS)

  • DS1 error detection:

    • Bursty errored seconds (BES)

    • CRC errors

    • Errored seconds (ES)

    • Line errored seconds (LES)

    • Loss of framing seconds (LOFS)

    • Severely errored seconds (SES)

    • Severely errored framing seconds (SEFS)

    • Unavailable seconds (UAS)

  • DS3 alarms:

    • Alarm indication signal (AIS)

    • Loss of frame (LOF)

    • Yellow alarm

  • DS3 error detection:

    • C-bit code violations (CCV)

    • C-bit errored seconds (CES)

    • C-bit severely errored framing seconds (CEFS)

    • CRC errors

    • Excessive zeros (EXZ)

    • Far-end block error (FEBE)

    • Far-end receive failure (FERF)

    • Line errored seconds (LES)

    • Parity bit (P-bit) code violations (PCV)

    • Parity bit (P-bit) errored seconds (PES)

    • Parity bit (P-bit) severely errored framing seconds (PSES)

    • Severely errored framing seconds (SEFS)

    • Unavailable seconds (UAS)

Instrumentation (counters)

  • Layer 2 per-queue and per-channel packet and byte counters

Note

Do not install Type 2 IQE PICs in both PIC slot number 2 and PIC slot number 3 of the M120-FPC2. You can install one 4-port Channelized OC12/STM4 IQE PIC or one 1-port Channelized OC48/STM4 IQE PIC into either PIC slot number 2 or PIC slot number 3. In the other slot, you can install any Type 2 PIC except the 8-port Gigabit Ethernet IQ2 PIC or 8-port Gigabit Ethernet IQ2E PIC.

Table 1: PICs Supported in Fourth Slot of M120-FPC2 with Type 2 IQE PICs on M120 Routers

PIC Name

PIC Model Number

Gigabit Ethernet, 2-port SFP

PB-2GE-SFP

Gigabit Ethernet, 4-port SFP

PB-4GE-SFP

Gigabit Ethernet IQ, 2-port SFP

PB-2GE-SFP-QPP

SONET/SDH OC12c/STM4, 4-port with multimode transceivers installed

PB-4OC12-SON-MM

SONET/SDH OC12c/STM4, 4-port with single-mode intermediate reach transceivers installed

PB-4OC12-SON-SMIR

SONET/SDH OC48/STM16, 1-port SFP

PB-1OC48–SON-SFP

Tunnel Services

PB-TUNNEL

Related Documentation