Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 

ATM2 OC12/STM4 IQ PICs (M120 Router)

 
Figure 1: 1-Port ATM2 OC12/STM4 IQ PIC
1-Port ATM2 OC12/STM4 IQ PIC
Figure 2: 2-Port ATM2 OC12/STM4 IQ PIC
2-Port ATM2 OC12/STM4 IQ PIC

Software release

  • 1-port: Junos OS Release 8.0R2 and later (Type 1)

  • 2-port: Junos OS Release 8.0R2 and later (Type 2)

    End-of-life (see notification PSN-2013-03-891)

Note: These PICs are not supported in Junos OS Release 8.1R1.

For information on which FPCs support these PICs, seeM120 PIC/FPC Compatibility .

Description

  • One or two OC12 ports

  • Power requirement:

    • 1-port: 0.41 A @ 48 V (20 W)

    • 2-port: 0.52 A @ 48 V (25 W)

  • Fine-grained queuing per logical interface

  • Conforms to ANSI T1.105-1991 and T1E1.2/93-020R1

  • Complies with ATM and SONET/SDH standards

  • Alarm and event counting and detection

  • Compatible with well-known ATM switches

  • ATM switch ID, which displays the switch IP address and local interface name of the adjacent Fore ATM switches

Hardware features

  • ATM2 IQ 1-port OC12 PICs have one 3010 SAR for segmentation and reassembly into 53-byte ATM cells; ATM2 IQ 2-port OC12 PICs have dual 3010 SAR

  • High-performance parsing of SONET/SDH frames

  • ASIC-based packet segmentation and reassembly (SAR) management and output port queuing

  • 64 MB SDRAM memory for ATM SAR

  • Packet buffering, Layer 2 parsing

Software features

  • Circuit cross-connect for leveraging ATM access networks

  • User-configurable virtual circuit (VC) and virtual path (VP) support

  • Support for idle cell or unassigned cell transmission

  • OAM fault management processes alarm indication signal (AIS), remote defect indication (RDI), and loop cells

  • Point-to-point and point-to-multipoint mode Layer 2 counters per VC and per VP

  • Local and remote loopback

  • ATM Inverse ARP, which enables routers to automatically learn the IP address of the router on the far end of an ATM PVC

  • Simple Network Management Protocol (SNMP):

    • Management Information Base (MIB) 2 (RFC 1213)

    • ATM MIB (RFC 1695)

    • SONET MIB

  • Unspecified bit rate (UBR), realtime variable bit rate (VBRrt), nonrealtime variable bit rate (VBRnrt), and constant bit rate (CBR) traffic shaping

  • Per-VC or per-VP traffic shaping

  • Support for F4 OAM cells

  • Support for 16-bit VCI range

Cables and connectors

LEDs

One tricolor per port:

  • Off—Not enabled

  • Green—Online with no alarms or failures

  • Yellow—Online with alarms for remote failures

  • Red—Active with a local alarm; router has detected a failure

Alarms, errors, and events

  • Alarm indication signal (AIS-L, AIS-P)

  • Bit error rate signal degrade (BERR-SD), bit error rate signal fail (BERR-SF)

  • Bit interleaved parity errors B1, B2, B3

  • Errored seconds (ES-S, ES-L, ES-P), far-end bit errors REI-L, REI-P (CV-LFE, CV-PFE), far-end errored seconds (ES-LFE, ES-PFE), far-end severely errored seconds (SES-LFE, SES-PFE), far-end unavailable seconds (UAS-LFE, UAS-PFE)

  • Loss of cell delineation (LOC), loss of frame (LOF), loss of pointer (LOP-P), loss of signal (LOS)

  • Payload mismatch (PLM-P), payload unequipped (UNEQ-P)

  • Remote defect indication (RDI-L, RDI-P)

  • Severely errored framing (SEF), severely errored framing seconds (SEFS-S), severely errored seconds (SES-S, SES-L, SES-P), unavailable seconds (UAS-L, UAS-P)