SONET/SDH OC192/STM64 MIC with XFP

 
Figure 1: SONET/SDH OC192/STM64 MIC with XFP
SONET/SDH OC192/STM64 MIC with XFP

Software release

  • Junos OS Release 12.2 and later

For information on which MPCs support this MIC, see MIC/MPC Compatibility. For information on which MICs are supported on MX Series routers, see MICs Supported by MX Series Routers.

Description

  • One OC192 port

  • Clear channel functionality

  • Power requirement: 4.25 A @ 9 V (38.25 W)

  • Weight: 1.34 lb (0.61 kg)

  • Model number: MIC-3D-1OC192-XFP

Hardware features

  • Maximum transmission units (MTUs) of up to 9192 bytes

  • MIC bandwidth of up to 10 Gbps

Software features

  • SONET/SDH framing

  • Multiprotocol Label Switching (MPLS) fast reroute

  • Ingress behavior aggregate (BA) classification

  • Internal and loop clocking

  • Encapsulations:

    • MPLS fast reroute

    • MPLS CCC (circuit cross-connection)

    • MPLS TCC (translational cross-connection)

    • Cisco High-Level Data Link Control (cHDLC)

    • Cisco HDLC CCC

    • Cisco HDLC TCC

    • Point-to-Point Protocol (PPP)

    • PPP for CCC

    • PPP for TCC

    • Flexible Frame Relay

    • Frame Relay

    • Frame Relay for CCC

    • Frame Relay for TCC

    • PPP over Frame Relay

    Note: Ethernet over Frame Relay is not supported.

Cables and connectors

Tip: You can use the Hardware Compatibility Tool to find information about the pluggable transceivers supported on your Juniper Networks device.

The list of supported transceivers for the MX Series is located at https://pathfinder.juniper.net/hct/category/#catKey=100001&modelType;=All&pf;=MX+Series.

Note: To extend the life of the laser, when a MIC is not being actively used with any valid links, take the MIC offline until you are ready to establish a link to another device. For information about taking a MIC offline, see the request chassis pic offline command in the CLI Explorer.

LEDs

OK/FAIL LED, one bicolor:

  • Green—MIC is functioning normally

  • Red—MIC has failed

LINK LED, one tricolor per port:

  • Off—Not enabled

  • Green—Online with no alarms or failures

  • Yellow—Online with alarms for remote failures

  • Red—Active with a local alarm; router has detected a failure

Alarms, errors, and events

SONET alarms:

  • Loss of light (LOL)

  • Phase lock loop (PLL)

  • Loss of signal (LOS)

  • Loss of frame (LOF)

  • Severely errored frame (SEF)

  • Alarm indicator signal–line (AIS-L)

  • Alarm indicator signal–path (AIS-P)

  • Remote defect indicator–line (RDI-L)

  • Remote defect indicator–path (RDI-P)

  • Loss of pointer–path (LOP-P)

  • Bit error rate–signal degrade (BERR-SD)

  • Bit error rate–signal fail (BERR-SF)

  • Payload label mismatch–Path (PLM-P)

  • Unequipped–path (UNEQ-P)

  • Remote error indicator–path (REI-P)



SDH alarms:

  • Loss of light (LOL)

  • Phase lock loop (PLL)

  • Loss of frame (LOF)

  • Loss of signal (LOS)

  • Severely errored frame (SEF)

  • Multiplex-section alarm indicator signal (MS-AIS)

  • Higher order path–alarm indication signal (HP-AIS)

  • Loss of pointer (LOP)

  • Bit error rate–signal degrade (BER-SD)

  • Bit error rate–signal fail (BER-SF)

  • Multiplex section–far end receive failure (MS-FERF)

  • Higher order path—far-end receive failure (HP-FERF)

  • Higher order path—payload label mismatch (HP-PLM)

  • Remote error indicator (REI)

  • Unequipped (UNEQ)

Related Documentation