100-Gigabit DWDM OTN MIC with CFP2-ACO

 

Software release

Description

  • One 100-Gigabit DWDM OTN port

  • Power requirements (including transceiver) at different temperatures:

    • 55° C: 1.90 A @ 48 V (91 W)

    • 25° C: 1.73 A @ 48 V (83 W)

  • Weight: 2.3 lb (1.04 kg)

  • Model number: MIC3-100G-DWDM

  • Name in the CLI: 1X100GE DWDM CFP2-ACO

Hardware features

  • Dual-wide MIC that installs into two MIC slots

  • Supports CFP2 analog coherent optics (CFP2-ACO)

  • Transparent transport of a 100-Gigabit Ethernet signal with OTU4V framing

  • ITU-standard OTN performance monitoring and alarm management

  • Dual-polarization quadrature phase shift keying (DP-QPSK) modulation

  • Supports three types of forward error correction (FEC):

    • Soft-decision FEC (SD-FEC)

    • High-gain FEC (HG-FEC)

    • G.709 FEC (GFEC)

  • 100 channels on C-band ITU grid with 50-GHz spacing

  • Latency:

    • SD-FEC: 14 µs (TX + RX)

    • HG-FEC: 22 µs (TX + RX)

    • GFEC: 6 µs (TX + RX)

  • Interoperable with the CFP-100GBASE-ZR transceiver supported on the 100-Gigabit Ethernet MIC with CFP (MIC3-3D-1X100GE-CFP) on MX Series routers and the 100-Gigabit Ethernet PIC with CFP (P1-PTX-2-100GE-CFP) on PTX Series routers.

  • Interoperable with the 100-Gigabit DWDM OTN PIC with CFP2 (PTX-5-100G-WDM) on PTX Series routers when the 100-Gigabit DWDM OTN MIC is configured to use SD-FEC or GFEC.

Note: The 1-port 100-Gigabit DWDM OTN MIC is not directly interoperable with the 2-port 100-Gigabit DWDM OTN PIC (P1-PTX-2-100G-WDM), but they can both operate over the same DWDM line system.

Software features

Note: For information about configuring the MIC, see Configuring OTN Interfaces on MIC3-100G-DWDM MIC. For information about upgrading the firmware on the PIC, see Upgrading Firmware on the 100-Gigabit DWDM OTN MIC (MIC3-100G-DWDM) .

  • Compliant with ITU G.709 and G.798

  • Provides a transport interface and state model (GR-1093)

  • Performance monitoring features such as alarms, threshold-crossing alarms, OTU/ODU error seconds and FEC and bit error rate (BER) statistics

  • SNMP management of the MIC based on RFC 3591, Managed Objects for the Optical Interface Type, including the following:

    • Set functionality

    • Black Link MIB

    • IFOTN MIB

    • Optics MIB

    • FRU MIB

  • Pre-FEC BER monitoring provides interrupt-driven, BER-based detection of link signal degradation for MPLS fast reroute.

  • User-configurable optics options:

    • Transmit (TX) laser enable and disable

    • TX output power

    • Wavelength

    • Receive (RX) LOS warning or alarm thresholds

    • Threshold crossing alarms (TCAs)

    User-configurable card options:

    • FEC mode (SD-FEC, HG-FEC, or GFEC)

    • TCAs

Cables and connectors

Tip: You can use the Hardware Compatibility Tool to find information about the pluggable transceivers supported on your Juniper Networks device.

The list of supported transceivers for the MX Series is located at https://pathfinder.juniper.net/hct/category/#catKey=100001&modelType;=All&pf;=MX+Series.

Note: When inserting the C form-factor pluggable 2 (CFP2) transceiver, ensure that the transceiver sits tightly in the port. You hear a distinct click sound when the latch locks into the corresponding port. The latch must be fully engaged in the corresponding port for the CFP2 transceiver to function properly. Failing to do so can result in loss of connection.

To verify that the CFP2 transceiver module is inserted properly, give a gentle pull by grasping the sides of the module. The module should sit tightly.

LEDs

OK/FAIL LED, one bicolor:

  • Off—MIC is powered off.

  • Green—MIC is initialized and online, functioning normally.

  • Amber—MIC is coming online, or is in fault state.

LINK LED, one bicolor per port:

  • Off—Port is offline.

  • Solid green—Link is up.

  • Red—Port failure is detected.

Note: The port is labeled Port 0.

Alarms, Errors, and Events

Note: For OTN alarms, see Table 1.

Chassis and MIC:

  • MIC (FRU) inserted or removed

  • MIC (FRU) Administrative State: In Service, Out Of Service

  • MIC (FRU) Operational State: Unequipped, Init, Normal, Mismatch, Fault, Upgrade

  • Mismatch equipment

  • Temperature alarm

 

Port (interface):

  • Interface Administrative State: In Service, Out Of Service, Service MA, Out of Service MA

  • Interface Operational State: Init, Normal, Fault, Degraded

 

Optical channel transport unit (OTU) TCAs:

  • OTU-TCA-BBE—15-minute background block error TCA

  • OTU-TCA-ES—15-minute far-end errored seconds TCA

  • OTU-TCA-SES—15-minute severely errored seconds TCA

  • OTU-TCA-UAS—15-minute unavailable seconds TCA

Optical channel data unit (ODU) TCAs:

  • ODU-TCA-BBE—15-minute background block error TCA

  • ODU-TCA-ES—15-minute far-end errored seconds TCA

  • ODU-TCA-SES—15-minute severely errored seconds TCA

  • ODU-TCA-UAS—15-minute unavailable seconds TCA

Tip: You can view OTU and ODU TCAs by using the show interfaces transport pm otn operational-mode CLI command.

 

Note: If you insert an invalid CFP module, the CLI displays unsupported module and a syslog message is generated.

Optics-related status:

  • Module temperature

  • Module voltage

  • Module temperature alarm:

    • High alarm

    • Low alarm

    • High warning

    • Low warning

  • Module voltage alarm:

    • High alarm

    • Low alarm

    • High warning

    • Low warning

  • Module not ready alarm

  • Module low power alarm

  • Module initialization incomplete alarm

  • Module fault alarm

  • TX laser disabled alarm

  • RX loss of signal alarm

  • Modem lock state

  • TX output power:

    • Current TX output power

    • Minimum over PM interval

    • Maximum over PM interval

    • Average over PM interval

  • TX power alarm:

    • High alarm

    • Low alarm

    • High warning

    • Low warning

  • RX input power (signal)

  • RX input power (total):

    • Current RX input power (total)

    • Minimum over PM interval

    • Maximum over PM interval

    • Average over PM interval

  • RX power alarm:

    • High alarm

    • Low alarm

    • High warning

    • Low warning

  • RX loss of signal alarm

  • Wavelength unlocked alarm

Tip: You can view optics-related status by using the show interfaces transport pm optics and show interfaces diagnostics optics operational-mode CLI commands.

 

Network lane receive-related status:

  • Chromatic dispersion:

    • Current chromatic dispersion

    • Minimum over PM interval

    • Maximum over PM interval

    • Average over PM interval

  • Differential group delay:

    • Current differential group delay

    • Minimum over PM interval

    • Maximum over PM interval

    • Average over PM interval

  • Q2-factor:

    • Current Q2-factor

    • Minimum over PM interval

    • Maximum over PM interval

    • Average over PM interval

  • Carrier frequency offset

    • Current carrier frequency offset

    • Minimum over PM interval

    • Maximum over PM interval

    • Average over PM interval

  • Signal-to-noise ratio (SNR)

    • Current SNR

    • Minimum over PM interval

    • Maximum over PM interval

    • Average over PM interval

Tip: You can view network lane receive-related status by using the show interfaces transport pm optics operational-mode CLI command.

 

FEC statistics:

  • Corrected Errors—the number of bits received that were in error, but corrected.

  • Uncorrected Words—the number of FEC codewords received that were uncorrectable.

  • Corrected Error Ratio—the number of corrected bits divided by the number of bits received

Tip: You can view FEC statistics by using the show interfaces interface-name extensive operational-mode CLI command.

Table 1 describes the OTN alarms and defects that can occur on the MIC and the link status when the alarm or defect occurs.

Tip

You can view OTN alarms and defects by using the show interfaces interface-name extensive operational-mode CLI command.

Table 1: OTN Alarms and Defects

Category

Alarm

Description

Link Status

OTN

LOS

Loss of signal

Link down

LOF

Loss of frame

Link down

LOM

Loss of multiframe

Link down

OTN FEC

FEC Degrade (OTU-FEC-DEG)

Forward error correction degraded

Link down if signal degrade or backward FRR thresholds are met

FEC Excessive (OTU-FEC-EXE)

There are uncorrected words and there are errors in the frame header

Possible link down

OTN OTU

OTU-AIS

Alarm indication signal or all ones signal

Link down

OTU-BDI

Backward defect identification

Link down

OTU-IAE

Incoming alignment error

Warning

OTU-TTIM

Destination access point identifier (DAPI), source access point identifier (SAPI), or both mismatch from expected to received

Can cause the link to be down if otu-ttim-act-enable is configured at the [edit interfaces interface-name otn-options]hierarchy level

OTU-BIAE

Backward incoming alignment error

Warning

OTU-TSF

OTU trail signal fail

Warning

OTU-SSF

OTU server signal fail

Warning

OTN ODU

ODU-AIS

Alarm indication signal or all ones signal

Link down

ODU-OCI

Open connection error

Link down

ODU-LCK

ODU lock triggers for path monitoring and TCM levels 1 through 6

Link down

ODU-BDI

Backward defect indication

Link down

ODU-TTIM

DAPI or SAPI mismatch from expected to received

Can cause the link to be down if odu-ttim-act-enable is configured at the [edit interfaces interface-name otn-options] hierarchy level

ODU-IAE

Incoming alignment error

Warning

ODU-LTC

Loss of tandem connection

Warning

ODU-CSF

Client signal failure

Warning

ODU-TSF

Trail signal fail

Warning

ODU-SSF

Server signal fail

Warning

ODU-PTIM

Payload type mismatch

Link down