SRX5K-MPC3-100G10G Specifications

 

The SRX5K-MPC3-100G10G (IOC3) is an interface card that provides 100 Gigabit Ethernet and 10 Gigabit Ethernet interfaces, with a Packet Forwarding Engine that provides a 240 Gbps line rate. This interface card is supported on SRX5400, SRX5600, and SRX5800 Services Gateways. See Figure 1.

Note

These cards do not support plug-in Modular Interface Cards (MICs).

All ports on the interface card have dual-color LEDs for reporting link status.

The interface card also supports hot-pluggable optical modules.

Figure 1: SRX5K-MPC3-100G10G
SRX5K-MPC3-100G10G

If a slot in the SRX5400, SRX5600, or SRX5800 Services Gateway card cage is not occupied by a card, you must install a blank panel to shield the empty slot and to allow cooling air to circulate properly through the services gateway.

Description

  • Fixed-configuration MPC with two 100-Gigabit Ethernet ports and four 10-Gigabit Ethernet ports

  • Maximum throughput: 240 Gbps

  • Maximum configurable MTU: 9192 bytes

Software release

Junos OS Release 15.1X49-D10 and later

Supported Slots

  • SRX5400 – Any slot, except the bottom slot 0 which is reserved for SCB/RE.

  • SRX5600 – Any slot, except the bottom slots 0 or 1 which are reserved for SCB/RE.

  • SRX5800 – Any slot, except the middle slots 0, 1, and 2/6 which are reserved for SCB/RE and slots 0 (left most) and 11 (right most).

    Note: You can use the 2/6 slot to install an interface card if an SCB is not already installed in it.

Cables and connectors

Sockets for 100-Gbps and 10-Gbps SFP+ transceivers

See Hardware Compatibility Tool for the transceivers supported.

Power requirements

  • Typical: 10.52 A @ 48 V (505 W)

At different temperatures:

  • 55° C: 607 W

  • 40° C: 541 W

  • 25° C: 511 W

Weight

21 lb (9.52 kg)

Hardware features

  • Line-rate throughput of up to 240 Gbps

  • Supports up to 32,000 queues per-slot

  • LAN-PHY mode at 10.3125 Gbps on a per-port basis

The ports are labeled as:

  • 10-Gigabit Ethernet ports: 0/0, 0/1, 2/0, and 2/1

  • 100-Gigabit Ethernet ports: 1/0 and 3/0

Software features

  • Configurable LAN-PHY mode options per 10-Gigabit Ethernet port

  • Optical diagnostics and related alarms

  • Intelligent oversubscription services

LEDs

OK/FAIL LED, one bicolor:

  • Solid green—MPC is functioning normally.

  • Blinking green—MPC is transitioning online or offline.

  • Red—MPC has failed.

10-Gigabit Ethernet LINK LED, one bicolor per port:

  • Green—Link is up.

  • Amber—Link is disabled.

  • Off—Link is down or disabled.

100-Gigabit Ethernet LINK LED, one bicolor per port:

  • Green—Link is up.

  • Amber—Link is disabled.

  • Off—Link is down.

Serial Number Location

The serial number label is located as shown in Figure 2.

Figure 2: SRX5K-MPC3-100G10G Serial Number Label
SRX5K-MPC3-100G10G Serial Number Label