Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation  Back up to About Overview 
  
[+] Expand All
[-] Collapse All

Related Documentation

  • Configuring Firewall Filters (CLI Procedure)
  • Example: Configuring Firewall Filters for Port, VLAN, and Router Traffic on EX Series Switches
  • Verifying That Firewall Filters Are Operational
  • Firewall Filters for EX Series Switches Overview
  • Firewall Filter Match Conditions, Actions, and Action Modifiers for EX Series Switches

Configuring Firewall Filters (J-Web Procedure)

Note: This topic applies only to the J-Web Application package.

You configure firewall filters on EX Series switches to control traffic that enters ports on the switch or enters and exits VLANs on the network and Layer 3 (routed) interfaces. To configure a firewall filter, you must configure the filter and then apply it to a port, VLAN, or Layer 3 interface.

To configure firewall filter settings by using the J-Web interface:

  1. Select Configure > Security > Filters.

    The Firewall Filter Configuration page displays a list of all configured ports or VLANs or router filters and the ports or VLANs associated with a particular filter.

    Note: After you make changes to the configuration on this page, you must commit the changes for them to take effect. To commit all changes to the active configuration, select Commit Options > Commit. See Using the Commit Options to Commit Configuration Changes for details about all commit options.

  2. Click one of the following options:
    • Add—Select this option to create a new filter. Enter information as specified in Table 47.
    • Edit—Select this option to edit an existing filter. Enter information as specified in Table 47.
    • Delete—Select this option to delete a filter.
    • Term Up—Select this option to move a term up in the filter term list.
    • Term Down—Select this option to move a term down in the filter term list.

Table 47: Create a New Filter

Field

Function

Your Action

Filter tab

Filter type

Specifies the filter type: port or VLAN firewall filter or router firewall filter.

Select the filter type.

Filter name

Specifies the name for the filter.

Enter a name.

Select terms to be part of the filter

Specifies the terms to be associated with the filter. Add new terms or edit existing terms.

Click Add to add new terms. Enter information as specified in Table 48 and Table 49.

Association tab

Port Associations

Specifies the ports with which the filter is associated.

Note: For a port or VLAN filter type, only Ingress direction is supported for port association.

  1. Click Add.
  2. Select the direction: Ingress or Egress.
  3. Select the ports. For an EX8200 Virtual Chassis configuration, select the member, FPC, and the available ports from the list.
  4. Click OK.

VLAN Associations

Specifies the VLANs with which the filter is associated.

Note: Because router firewall filters can be associated with ports only, this section is not displayed for a router firewall filter.

  1. Click Add.
  2. Select the direction: Ingress or Egress.
  3. Select the VLANs.
  4. Click OK.

Table 48: Create a New Term

Field

Function

Your Action

Term Name

Specifies the name of the term.

Enter a name.

Protocols

Specifies the protocols to be associated with the term.

  1. Click Add.
  2. Select the protocols.
  3. Click OK.

Source

Specifies the source IP address, MAC address, and available ports.

Note: MAC address is specified only for port or VLAN filters.

To specify the IP address, click Add > IP and enter the IP address.

To specify the MAC address, click Add > MAC and enter the MAC address.

To specify the ports (interfaces), click Add > Ports and enter the port number.

To delete the IP address, MAC address, or port details, select it and click Remove.

Destination

Specifies the destination IP address, MAC address, and available ports.

Note: MAC address is specified only for port or VLAN filters.

To specify the IP address, click Add > IP and enter the IP address.

To specify the MAC address, click Add > MAC and enter the MAC address.

To specify the ports (interfaces), click Add > Ports and enter the port number.

To delete the IP address, MAC address, or port details, select it and click Remove.

Action

Specifies the packet action for the term.

Select one of the following options:

  • Accept
  • Discard

More

Specifies advanced configuration options for the filter.

Select the match conditions as specified in Table 49.

Select the packet action for the term as specified in Table 49.

Table 49: Advanced Options for Terms

Table

Function

Your Action

ICMP Type

Specifies the ICMP packet type field. Typically, you specify this match condition in conjunction with the protocol match condition to determine which protocol is being used on the port.

Select the option from the list.

ICMP Code

Specifies more specific information than the ICMP type. Because the value’s meaning depends upon the associated ICMP type, you must specify icmp-type along with icmp-code. The keywords are grouped by the ICMP type with which they are associated.

Select a value from the list.

DSCP

Specifies the Differentiated Services code point (DSCP). The DiffServ protocol uses the type-of-service (ToS) byte in the IP header. The most significant six bits of this byte form the DSCP.

Select the DSCP number from the list.

Precedence

Specifies the IP precedence.

Note: The IP precedence and the DSCP number cannot be specified together for the same term.

Select the option from the list.

IP Options

Specifies the presence of the options field in the IP header.

Select the option from the list.

Interface

Specifies the interface on which the packet is received.

Select the interface from the list.

Ether type

Note: This option is not supported on EX4300 switches.

Specifies the Ethernet type field of a packet.

Note: This option is not applicable for a routing filter.

Select a value from the list.

Dot 1q user priority

Note: This option is not supported on EX4300 switches.

Specifies the user-priority field of the tagged Ethernet packet. User-priority values can be 0–7.

In place of the numeric value, you can specify one of the following text synonyms (the field values are also listed) :

  • background (1)—Background
  • best-effort (0)—Best effort
  • controlled-load (4)—Controlled load
  • excellent-load (3)—Excellent load
  • network-control (7)—Network control reserved traffic
  • standard (2)—Standard or spare
  • video (5)—Video
  • voice (6)—Voice

Note: This option is not applicable for a routing filter.

Select a value from the list.

VLAN

Note: This option is not supported on EX4300 switches.

Specifies the VLAN to be associated with the packet.

Note: This option is not applicable for a routing filter.

Select the VLAN from the list.

TCP Flags

Specifies one or more TCP flags.

Note: TCP flags are supported on ingress ports, VLANs, and router interfaces.

Select the option TCP Initial or enter a combination of TCP flags.

Fragmentation Flags

Specifies the IP fragmentation flags.

Note: Fragmentation flags are supported on ingress ports, VLANs, and router interfaces.

Select either the option is-fragment or enter a combination of fragment action flags.

Dot1q tag

Note: This option is not supported on EX4300 switches.

Specifies the value for the tag field in the Ethernet header. The value can be from 1 through 4095.

Note: This option is not applicable for a routing filter.

Enter the value.

User Vlan Id

Note: This option is supported only on EX4300 switches.

Specifies the value of the VLAN ID. The value can be from 0 through 4095 or a range of values.

Enter a value.

User Vlan 1P Priority

Note: This option is supported only on EX4300 switches.

Specifies the priority value. The values can be from 0 through 7.

Enter a value.

Learn Vlan Id

Note: This option is supported only on EX4300 switches.

Specifies the value of the learnt VLAN ID. The value can be from 0 through 4095 or a range of values.

Enter a value.

Action

Counter name

Specifies the count of the number of packets that pass this filter, term, or policer.

Enter a value.

Forwarding class

Classifies the packet into one of the following forwarding classes:

  • assured-forwarding
  • best-effort
  • expedited-forwarding
  • network-control
  • None

Select the option from the list.

Loss priority

Specifies the packet loss priority.

Note: Forwarding class and loss priority must be specified together for the same term.

Enter the value.

Analyzer

Note: This option is not supported on EX4300 switches.

Specifies whether to perform port mirroring on packets. Port mirroring copies all packets entering one switch port to a network- monitoring connection on another switch port.

Select the analyzer (port mirroring configuration) from the list.

Port Mirror Instance

Note: This option is supported only on EX4300 switches.

Specifies whether to perform port mirroring on packets. Port mirroring copies all packets entering one switch port to a network- monitoring connection on another switch port.

Select the port mirroring instance from the list. Default is selected by default.

Related Documentation

  • Configuring Firewall Filters (CLI Procedure)
  • Example: Configuring Firewall Filters for Port, VLAN, and Router Traffic on EX Series Switches
  • Verifying That Firewall Filters Are Operational
  • Firewall Filters for EX Series Switches Overview
  • Firewall Filter Match Conditions, Actions, and Action Modifiers for EX Series Switches

Modified: 2017-03-05