Reinstalling Components in the SRX5600 Services Gateway Chassis After Installing It Without a Lift

After the services gateway is installed in the rack, reinstall the removed components before booting and configuring the services gateway. You reinstall components first in the rear of the chassis, and then in the front:

  1. Reinstalling Power Supplies After Installing the SRX5600 Services Gateway Without a Lift
  2. Reinstalling the Fan Tray After Installing the SRX5600 Services Gateway Without a Lift
  3. Reinstalling SCBs After Installing the SRX5600 Services Gateway Without a Lift
  4. Reinstalling IOCs, Flex IOCs, and SPCs After Installing the SRX5600 Services Gateway Without a Lift

Reinstalling Power Supplies After Installing the SRX5600 Services Gateway Without a Lift

Reinstall the rightmost power supply first and then work your way to the left. To reinstall the AC or DC power supplies, follow this procedure for each power supply (see Figure 85, which shows the installation of the DC power supplies):

  1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
  2. On an AC-powered services gateway, switch the AC input switch on each power supply to the off (O) position. On a DC-powered services gateway, move the DC circuit breaker on each DC power supply to the off  (O) position.

    We recommend this even though the power supplies are not connected to power sources.

  3. Using both hands, slide the power supply straight into the chassis until the power supply is fully seated in the chassis slot. The power supply faceplate should be flush with any adjacent power supply faceplate or blank installed in the power supply slot.
  4. Tighten the captive screws.

Figure 85: Reinstalling a Power Supply

Image g004262.gif

Reinstalling the Fan Tray After Installing the SRX5600 Services Gateway Without a Lift

To reinstall the fan tray (see Figure 86):

  1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
  2. Grasp the fan tray on each side and insert it straight into the chassis. Note the correct orientation by the "this side up" label on the top surface of the fan tray.
  3. Tighten the captive screws on the fan tray faceplate to secure it in the chassis.

Figure 86: Reinstalling the Fan Tray

Image g004226.gif

Reinstalling SCBs After Installing the SRX5600 Services Gateway Without a Lift

To reinstall an SCB (see Figure 87):

Caution: Before removing or replacing an SCB, ensure that the ejector handles are stored horizontally and pressed toward the center of the SCB.

  1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
  2. Carefully align the sides of the SCB with the guides inside the chassis.
  3. Slide the SCB into the chassis until you feel resistance, carefully ensuring that it is correctly aligned.
  4. Grasp both ejector handles and rotate them simultaneously clockwise until the SCB is fully seated.
  5. Place the ejector handles in their proper position, horizontally and toward the center of the board. To avoid blocking the visibility of the LEDs position the ejectors over the PARK icon.

Figure 87: Reinstalling an SCB

Image g004230.gif

Reinstalling IOCs, Flex IOCs, and SPCs After Installing the SRX5600 Services Gateway Without a Lift

To reinstall IOCs, Flex IOCs, and SPCs, follow this procedure for each card (see Figure 88):

  1. Place the card on an antistatic mat or remove it from its electrostatic bag.
  2. Identify the slot on the services gateway where it will be installed.
  3. Verify that each fiber-optic has a rubber safety cap covering the transceiver. If it does not, cover the transceiver with a safety cap.
  4. Orient the card so that the faceplate faces you.
  5. Lift the card into place and carefully align the sides of the card with the guides inside the card cage.
  6. Slide the card all the way into the card cage until you feel resistance.
  7. Grasp both ejector handles and rotate them clockwise simultaneously until the card is fully seated.

Figure 88: Installing an IOC, Flex IOC, or SPC

Image g030239.gif