Replacing an SRX5600 Services Gateway DC Power Supply

To replace a DC power supply, perform the following procedures:

  1. Removing an SRX5600 Services Gateway DC Power Supply
  2. Installing an SRX5600 Services Gateway DC Power Supply

Removing an SRX5600 Services Gateway DC Power Supply

The power supplies are located at the rear of the chassis. Each DC power supply weighs approximately 3.8 lb (1.7 kg).

Caution: Do not leave a power supply slot empty for more than 30 minutes while the services gateway is operational. For proper airflow, the power supply must remain in the chassis, or a blank panel must be used in an empty slot.

Note: After powering off a power supply, wait at least 60 seconds before turning it back on.

To remove a DC power supply (see Figure 67):

  1. Switch off the dedicated facility circuit breaker for the power supply being removed. Follow your site's procedures for ESD.
  2. Make sure that the voltage across the DC power source cable leads is 0 V and that there is no chance that the cables might become active during the removal process.
  3. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
  4. Switch the circuit breaker on the power supply faceplate to the OFF position O.
  5. Remove the clear plastic cover protecting the terminal studs on the faceplate.
  6. Remove the nuts and washers from the terminal studs. (Use a 3/8-in. nut driver or socket wrench.)
  7. Remove the cable lugs from the terminal studs.
  8. Loosen the captive screws on the bottom edge of the power supply faceplate.
  9. Carefully move the power cables out of the way.
  10. Pull the power supply straight out of the chassis.

Figure 67: Removing a DC Power Supply

Image g004240.gif

Installing an SRX5600 Services Gateway DC Power Supply

To install a DC power supply (see Figure 68):

  1. Ensure that the voltage across the DC power source cable leads is 0 V and that there is no chance that the cable leads might become active during installation.
  2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
  3. Switch the circuit breaker on the power supply faceplate to the OFF position O.
  4. Using both hands, slide the power supply straight into the chassis until the power supply is fully seated in the chassis slot. The power supply faceplate should be flush with any adjacent power supply faceplate (see Figure 68).
  5. Tighten the captive screws on the lower edge of the power supply faceplate.
  6. Remove the clear plastic cover protecting the terminal studs on the faceplate.
  7. Remove the nuts and washers from the terminal studs.
  8. Secure each power cable lug to the terminal studs, first with the washer, then with the nut. Apply between 23 lb-in. (2.6 Nm) and 25 lb-in. (2.8 Nm) of torque to each nut. (see Figure 69).
    1. Attach the positive (+) DC source power cable lug to the RTN (return) terminal.
    2. Attach the negative (–) DC source power cable lug to the –48V (input) terminal.

    Caution: You must ensure that power connections maintain the proper polarity. The power source cables might be labeled (+) and (–) to indicate their polarity. There is no standard color coding for DC power cables. The color coding used by the external DC power source at your site determines the color coding for the leads on the power cables that attach to the terminal studs on each power supply.

    Note: For the SRX5600 services gateway, the DC power supplies in PEM0 and PEM1 must be powered by dedicated power feeds derived from feed A, and the DC power supplies in PEM2 and PEM3must be powered by dedicated power feeds derived from feed B. This configuration provides the commonly deployed A/B feed redundancy for the system.

  9. Replace the clear plastic cover over the terminal studs on the faceplate.
  10. Route the power cables along the cable restraint towards the left or right corner of the chassis. If needed to hold the power cables in place, thread plastic cable ties, which you must provide, through the openings on the cable restraint.
  11. Verify that the power cabling is correct, that the cables are not touching or blocking access to services gateway components, and that they do not drape where people could trip on them.
  12. Verify that the INPUT OK LED on the power supply is lit green.
  13. Switch the circuit breaker on the power supply to the ON position and observe the status LEDs on the power supply faceplate. If the power supply is correctly installed and functioning normally, the PWR OK, BRKR ON, and INPUT OK LEDs light green steadily.

    Note: If more than one power supply is being installed, turn on all power supplies at the same time.

Note: An SCB must be present for the PWR OK LED to go on.

Figure 68: Installing a DC Power Supply

Image g004241.gif

Figure 69: Connecting DC Power

Image g004222.gif