[ Contents] [ Prev] [ Next] [ Index] [ Report an Error]

Replacing an I/O Card on the SRX3400 Services Gateway

I/O Cards (IOCs) are installed in the Services Gateway in slots labeled 1-4. Before you replace an IOC, you have the option of powering off the Services Gateway. If you leave the device powered up, traffic using the IOC will be interrupted during the replacement process. SFPs and XFPs are hot-insertable and hot-removable. Removing an SFP or XFP does not interrupt IOC functioning, but the removed SFP or XFP no longer receives or transmits data.

Note: Juniper strongly recommends the use of Juniper transceivers. Juniper cannot guarantee correct operation if non-Juniper transceivers are used. The transceiver type can be different in each port, as long as a supported part number is used.

To replace an IOC:

  1. Place an electrostatic bag or antistatic mat on a flat, stable surface.
  2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis. For more information about ESD, see Preventing Electrostatic Discharge Damage to the SRX3400 Services Gateway.
  3. If you have not already done so, power off the device by pressing the Power button on the front panel of the Switch Fabric Board (SFB) for three to five seconds.

    The PWR LED blinks to show you that the device is shutting down. Wait for the device to shut down before proceeding.

  4. Disconnect any cables connected to the Ethernet ports, marking them so they can be reconnected in the proper location. If the IOC uses fiber-optic cable, immediately cover each transceiver and the end of each cable with a rubber safety cap. Arrange the disconnected cables in the cable management system to prevent the cables from developing stress points.

    Warning: Do not look directly into a fiber-optic transceiver or into the ends of fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a transceiver emit laser light that can damage your eyes.

    Caution: Do not leave a fiber-optic transceiver uncovered except when inserting or removing cable. The safety cap keeps the port clean and prevents accidental exposure to laser light.

    Caution: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc smaller than a few inches in diameter can damage the cable and cause problems that are difficult to diagnose.

  5. Loosen the captive screws at each end of the IOC faceplate.
  6. Pull open the ejector handles to unseat the IOC.
  7. Grasp the IOC by the ejector handles and slide it halfway out of the chassis.
  8. Place one hand underneath the IOC to support it and slide it completely out of the chassis.

    Figure 56: Removing an IOC

    Image g036020.gif

  9. Place the IOC on the antistatic mat. If you are not reinstalling an IOC into the emptied slot within 30 minutes, install a blank panel over the slot to maintain proper airflow in the card cage.

    If you need to replace the transceivers, see Replacing SFP and XFP Transceivers on I/O Cards on the SRX3400 Services Gateway; otherwise, continue with step 10.

  10. Carefully align the sides of the replacement IOC with the guides inside the chassis.
  11. Slide the IOC into the slot until you feel resistance, and then press the IOC's faceplate until it engages the connectors.
  12. Press both of the ejector handles inward to seat the IOC.
  13. Tighten the captive screws on the left and right of the IOC.

    Figure 57: Installing an IOC

    Image g036019.gif

  14. If the IOC uses fiber-optic cable, remove the rubber safety cap from each transceiver and cable.

    Warning: Do not look directly into a fiber-optic transceiver or into the ends of fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a transceiver emit laser light that can damage your eyes.

  15. Insert the appropriate cables into the cable connector ports on each IOC.

    Caution: Do not let fiber-optic cable hang free from the connector. Do not allow fastened loops of cable to dangle, which stresses the cable at the fastening point.

    Caution: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc smaller than a few inches in diameter can damage the cable and cause problems that are difficult to diagnose.

  16. If you elected to power off the Services Gateway, power it on as described in Powering On the SRX3400 Services Gateway. Either way, the OK/FAIL LED on the IOC faceplate should blink green, then light steadily.

    Note: If the OK/FAIL LED is red, remove and reinstall the IOC. If the OK/FAIL LED remains red, the IOC is not functioning properly. Contact your customer support representative.

    Warning: Never lift the Services Gateway using the handles on the front panels of the IOCs or other CFM cards. The handles might come off, causing the chassis to drop and inflicting possible grave injury.

Related Topics


[ Contents] [ Prev] [ Next] [ Index] [ Report an Error]