Hide Navigation Pane
Show Navigation Pane
Download
SHA1
SRX240 Services Gateway LEDs
This topic includes the following sections:
- Front Panel LEDs
- Ethernet Port LEDs
- DC Power Feed LEDs (SRX240 Services Gateway with DC Power Supply Models)
Front Panel LEDs
Figure 5 shows the front panel LEDs of the SRX240 Services Gateway.
Figure 5: SRX240 Services Gateway Front Panel LEDs
Table 10 lists the LED indications on the SRX240 Services Gateway front panel.
Table 10: SRX240 Services Gateway Front Panel LEDs
Component | Description | Usage |
|---|---|---|
Status LED | The Status LED indications are:
| The Status LED can be used to determine whether the services gateway is starting up, is functioning normally, or has failed. |
Alarm LED | The Alarm LED indications are:
Note: When the system is up and running, if the Alarm LED is off, it indicates that no alarms are present on the services gateway. | The Alarm LED can be used to gather information on major or minor alarms; it indicates whether the services gateway is functioning normally. |
Power LED | The Power LED indications are:
| The Power LED indicates whether the services gateway is receiving power. |
HA LED | The HA LED indications are:
| The HA LED indicates whether chassis clustering is enabled on the services gateway. |
Mini-PIM LED | Each Mini-PIM LED provides the following indications:
| The Mini-PIM LED indicates whether a Mini-PIM is present and is detected by the services gateway. |
Ethernet Port LEDs
On the SRX240 Services Gateway, each Gigabit Ethernet port has the two LEDs as shown in Figure 6.
Figure 6: SRX240 Services Gateway Ethernet Port LEDs
Table 11: SRX240 Services Gateway Ethernet Port LEDs
Number | LED |
|---|---|
1 | TX/RX/Link LED |
2 | PoE (Power over Ethernet) LED |
 | Note: The PoE LED is enabled only on PoE models of the SRX240 Services Gateway. On non-PoE models, the PoE LED is always unlit. |
Table 12 describes the Ethernet port LEDs.
Table 12: SRX240 Services Gateway Ethernet Port LEDs
Function | Color | State | Description |
|---|---|---|---|
TX/RX/Link | Green | Blinking | Link is active. Data communication is taking place. |
Steady | Link is active. No data communication is taking place. | ||
Unlit | Off | Link is inactive. | |
PoE Status | Green | Steady | PoE is activated and the connected power device is receiving power. |
Yellow | Steady | PoE is activated, but the connected power device is not receiving power (there is fault or not enough power). | |
Unlit | Off | PoE is disabled or no device is drawing power. |
DC Power Feed LEDs (SRX240 Services Gateway with DC Power Supply Models)
On the SRX240 Services Gateway with DC power supply models, the back panel includes two LEDs, which indicate the status of the DC power feed LEDs.
Figure 7 shows the location of the DC power feed LEDs.
Figure 7: DC Power Feed LEDs
Table 13 describes the DC power feed LEDs.
Table 13: DC Power Feed LEDs
DC Input | DC Output | LED A | LED B | |
|---|---|---|---|---|
Input A | Input B | |||
Input is normal. | Input is normal. | No output1. | Red | Red |
Output is normal. | Green | Green | ||
Input is connected but has failed because the power supply fuse has failed or input voltage is low. | Input is normal. | Output is normal. | Red (blinking) | Green |
Input is normal. | Input is connected, but has failed because the power supply fuse has failed or the input voltage is low. | Output is normal. | Green | Red (blinking) |
Input breaker open or no DC input connected. | Input is normal. | Output is normal. | Red (blinking) | Green |
Input has failed. | Input has failed. | No output. | Red (blinking) | Red (blinking) |
No input. | No input. | No output. | Off | Off |
(1) No output because of an output side failure or an open connection. | ||||
