8-Port Gigabit Ethernet SFP XPIM Basic Configuration

The 8-Port Gigabit Ethernet small form-factor pluggable Gigabit-Backplane Physical Interface Module (SFP XPIM) provides connectivity to a single Gigabit Ethernet device or to a network. After you install the XPIM in the services gateway, you configure a network interface on the XPIM.

Note: Both the SRX550 and the SRX650 Services Gateways support hot-swappable functionality for XPIMs.

To configure a network interface on the 8-Port Gigabit Ethernet SFP XPIM :

  1. Verify that the 8-Port Gigabit Ethernet SFP XPIM is installed in the services gateway:

    user@host >show chassis hardware

    The following is a sample output of the command. (The output shown is for an SRX550 Services Gateway; other devices give similar output):

    Hardware inventory:
    Item             Version  Part number  Serial number     Description
    Chassis                                AL1011AA0013      SRX550
    Midplane         REV 02   750-035027   AADB5084
    Routing Engine   REV 07   711-035026   AADB5153          RE-SRXSME-SRX550
    FPC 0                                                    FPC
      PIC 0                                                  6x GE, 4x GE SFP Base PIC
    FPC 3            REV 03   750-037551   AAEC8075          FPC
      PIC 0                                                  8x GE SFP gPIM
        Xcvr 0       REV 02   740-013111   B302363           SFP-T
        Xcvr 1       REV 01   740-011612   9XT702501077      SFP-LH
        Xcvr 2       REV 01   740-011612   9XT702501078      SFP-LH
        Xcvr 3       REV 01   740-011612   9XT702501079      SFP-LH
        Xcvr 4       REV 01   740-011612   9XT702501080      SFP-LH
        Xcvr 5       REV 01   740-011620   2850670           SFP-FX
        Xcvr 6       REV 01   740-011782   P8Q21GG           SFP-SX
        Xcvr 7       REV 01   740-020465   5446212           SFP-1000BASE-BX10-D
    Power Supply 0   Rev 03   740-024283   VA11443           PS 645W AC
    

    The output shows that FPC 3 PIC 0 is the XPIM.

  2. Verify that the PIC on the XPIM is online:

    user@host> show chassis fpc pic-status

    The following sample output shows that FPC 3 PIC 0 is online:

    root@magni02-2a> show chassis fpc pic-status
    Slot 0   Online       FPC
      PIC 0  Online       6x GE, 4x GE SFP Base PIC
    Slot 3   Online       FPC
      PIC 0  Online       8x GE SFP gPIM         
    
  3. Verify that the network interface that you want to configure on the XPIM is up:

    user@host> show interfaces terse

    The following is a sample output for this command:

    root@magni02-2a> show interfaces terse ge-3/0/*
    Interface               Admin Link Proto    Local                 Remote
    ge-3/0/0                up    up
    ge-3/0/1                up    up
    ge-3/0/2                up    up
    ge-3/0/3                up    up
    ge-3/0/4                up    up
    ge-3/0/5                up    up
    ge-3/0/6                up    up
    ge-3/0/7                up    up
    

    The following sample output shows extensive details of ge-3/0/0 on the interface:

    root@magni02-2a> show interfaces ge-3/0/0 extensive | no-more Physical interface: ge-3/0/0, Enabled, Physical link is Up
    Interface index: 150, SNMP ifIndex: 722, Generation: 153
      Link-level type: Ethernet, MTU: 1514, Link-mode: Full-duplex, Speed: 1000mbps,
      BPDU Error: None, MAC-REWRITE Error: None, Loopback: Disabled,
      Source filtering: Disabled, Flow control: Enabled, Auto-negotiation: Enabled,
      Remote fault: Online
      Device flags   : Present Running
      Interface flags: SNMP-Traps Internal: 0x0
      Link flags     : None
      CoS queues     : 8 supported, 8 maximum usable queues
      Hold-times     : Up 0 ms, Down 0 ms
      Current address: 00:1f:12:e4:71:54, Hardware address: 00:1f:12:e4:71:54
      Last flapped   : 2012-04-03 00:28:04 PDT (23:49:14 ago)
      Statistics last cleared: Never
      Traffic statistics:
       Input  bytes  :                    0                    0 bps
       Output bytes  :                    0                    0 bps
       Input  packets:                    0                    0 pps
       Output packets:                    0                    0 pps
      Input errors:
        Errors: 0, Drops: 0, Framing errors: 0, Runts: 0, Policed discards: 0,
        L3 incompletes: 0, L2 channel errors: 0, L2 mismatch timeouts: 0,
        FIFO errors: 0, Resource errors: 0
      Output errors:
        Carrier transitions: 1, Errors: 0, Drops: 0, Collisions: 0, Aged packets: 0,
        FIFO errors: 0, HS link CRC errors: 0, MTU errors: 0, Resource errors: 0
      Active alarms  : None
      Active defects : None
      MAC statistics:                      Receive         Transmit
        Total octets                             0                0
        Total packets                            0                0
        Unicast packets                          0                0
        Broadcast packets                        0                0
        Multicast packets                        0                0
        CRC/Align errors                         0                0
        FIFO errors                              0                0
        MAC control frames                       0                0
        MAC pause frames                         0                0
        Oversized frames                         0
        Jabber frames                            0
        Fragment frames                          0
        VLAN tagged frames                       0
        Code violations                          0
      Filter statistics:
        Input packet count                       0
        Input packet rejects                     0
        Input DA rejects                         0
        Input SA rejects                         0
        Output packet count                                       0
        Output packet pad count                                   0
        Output packet error count                                 0
        CAM destination filters: 1, CAM source filters: 0
      Autonegotiation information:
        Negotiation status: Complete
        Link partner:
            Link mode: Full-duplex, Flow control: None, Remote fault: OK,
            Link partner Speed: 1000 Mbps
        Local resolution:
            Flow control: None, Remote fault: Link OK
      Packet Forwarding Engine configuration:
        Destination slot: 3
      CoS information:
        Direction : Output
        CoS transmit queue               Bandwidth               Buffer Priority   Limit
                                  %            bps     %           usec
        0 best-effort            95      950000000    95              0      low    none
        3 network-control         5       50000000     5              0      low    none
      Interface transmit statistics: Disabled
    
  4. Assign the interface an IP address:

    [edit]
    user@host# set interfaces interface-name unit 0 family inet address interface address/destination prefix

  5. Set security policies:

    [edit]
    user@host# set security policies policy-name

Related Documentation