TechLibrary

Navigation Back up to About Overview

ContentIndex

[+] Expand All

[-] Collapse All

Topics for Stout Line Card
- Copyright and Trademark Information
- Table of Contents
- List of Figures
- List of Tables
- About the Documentation
- Topics for Stout Line Card
  - New Topics for Stout
    - EX9200-40XS Line Card
      - Line Card Models
      - Line Card Components
    - EX9200-12QS Line Card
      - Line Card Models
      - Line Card Components
    - Configuring Rate Selectability on an EX9200-12QS Line Card to Enable Different Port Speeds
      - Configuring Rate Selectability at the PIC Level
      - Configuring Rate Selectability at the Port Level
  - Updated Common Topics for EX9200
  - Updated EX9204 Hardware Topics
    - EX9204 Switch Hardware Overview
    - Chassis Physical Specifications of an EX9204 Switch
    - EX9204 Switch Hardware and CLI Terminology Mapping
  - Updated EX9208 Hardware Topics
    - EX9208 Switch Hardware Overview
    - Chassis Physical Specifications of an EX9208 Switch
    - EX9208 Switch Hardware and CLI Terminology Mapping
  - Updated EX9214 Hardware Topics
    - EX9214 Switch Hardware Overview
    - Chassis Physical Specifications of an EX9214 Switch
    - EX9214 Switch Hardware and CLI Terminology Mapping
  - Topics Modified for PR 1138724
    - EX9200-2C-8XS Line Card
      - Line Card Models
      - Line Card Components
    - EX9200-6QS Line Card
      - Line Card Models
      - Line Card Components
    - EX9200-32XS Line Card
      - Line Card Models
      - Line Card Components

No index entries found.

Download This Guide

Download this guide: Topics for Stout Line Card

Pluggable Transceivers Supported on EX9200 Switches

The line cards in EX9200 switches support 1-gigabit small form-factor pluggable (SFP), 10-gigabit small form-factor pluggable plus (SFP+), 40-gigabit quad small form-factor pluggable plus (QSFP+), and 100-gigabit C form-factor pluggable (CFP) transceivers. This topic describes the optical interfaces supported for those transceivers.

Note: We recommend that you use only optical transceivers and optical connectors purchased from Juniper Networks with your Juniper Networks device.

Caution: If you face a problem running a Juniper Networks device that uses a third-party optic or cable, the Juniper Networks Technical Assistance Center (JTAC) can help you diagnose the source of the problem. Your JTAC engineer might recommend that you check the third-party optic or cable and potentially replace it with an equivalent Juniper Networks optic or cable that is qualified for the device.

The Gigabit Ethernet SFP, SFP+, and QSFP+ transceivers and the 100GBASE-LR4 CFP transceivers installed in EX9200 switches support digital optical monitoring (DOM): You can view the diagnostic details for these transceivers by issuing the operational mode CLI command show interfaces diagnostics optics.

The tables in this topic describe the optical interface support over single-mode fiber-optic (SMF) and multimode fiber-optic (MMF) cables for SFP, SFP+, QSFP+, and CFP transceivers:

Table 8—Optical interface support for Gigabit Ethernet SFP transceivers.
Table 9—Optical interface support for Fast Ethernet SFP transceivers.
Table 10—Optical interface support for SFP+ transceivers.
Table 12—Optical interface support for 40-gigabit QSFP+ transceivers.
Table 11—Optical interface support for 100-gigabit QSFP+ transceivers.
Table 13—Optical interface support for CFP transceivers.

Table 8: Optical Interface Support for Fast Ethernet and Gigabit Ethernet SFP Transceivers in EX9200 Switches

Ethernet Standard	Specification	Value
1000BASE-T	Model number	EX-SFP-1GE-T
	Rate	10/100/1000 Mbps
	Connector type	RJ-45
	Fiber count	Copper
	Transmitter wavelength	–
	Minimum launch power	–
	Maximum launch power	–
	Minimum receiver sensitivity	–
	Maximum input power	–
	Fiber type	Copper
	Core size	–
	Modal bandwidth	–
	Distance	100 m (328 ft)
	DOM support	Not available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
1000BASE-SX	Model number	EX-SFP-1GE-SX
	Rate	1000 Mbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	850 nm
	Minimum launch power	–9.5 dBm
	Maximum launch power	–3 dBm
	Minimum receiver sensitivity	–21 dBm
	Maximum input power	0 dBm
	Fiber type	MMF
	Core size	62.5/125 µm	62.5/125 µm
	Fiber grade	FDDI	OM1
	Modal bandwidth	160 MHz/km	200 MHz/km
	Distance	220 m (721 ft)	275 m (902 ft)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
1000BASE-LX	Model number	EX-SFP-1GE-LX
	Rate	1000 Mbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	1310 nm
	Minimum launch power	–9.5 dBm
	Maximum launch power	–3 dBm
	Minimum receiver sensitivity	–25 dBm
	Maximum input power	–3 dBm
	Fiber type	SMF
	Core size	9/125 µm
	Modal bandwidth	–
	Distance	10 km (6.2 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
1000BASE-BX-U	Model number	EX-SFP-GE10KT13R14
	Rate	1000 Mbps
	Connector type	LC
	Fiber count	Single
	Transmitter wavelength	1310 nm
	Receiver wavelength	1490 nm
	Minimum launch power	–9 dBm
	Maximum launch power	–3 dBm
	Minimum receiver sensitivity	–30 dBm
	Maximum input power	–3 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 μm
	Modal bandwidth	–
	Distance	10 km (6.2 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
1000BASE-BX-D	Model number	EX-SFP-GE10KT14R13
	Rate	1000 Mbps
	Connector type	LC
	Fiber count	Single
	Transmitter wavelength	1490 nm
	Receiver wavelength	1310 nm
	Minimum launch power	–9 dBm
	Maximum launch power	–3 dBm
	Minimum receiver sensitivity	–30 dBm
	Maximum input power	–3 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 μm
	Modal bandwidth	–
	Distance	10 km (6.2 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
1000BASE-BX-U	Model number	EX-SFP-GE10KT13R15
	Rate	1000 Mbps
	Connector type	LC
	Fiber count	Single
	Transmitter wavelength	1310 nm
	Receiver wavelength	1550 nm
	Minimum launch power	–9 dBm
	Maximum launch power	–3 dBm
	Minimum receiver sensitivity	–21 dBm
	Maximum input power	–3 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 μm
	Modal bandwidth	–
	Distance	10 km (6.2 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
1000BASE-BX-D	Model number	EX-SFP-GE10KT15R13
	Rate	1000 Mbps
	Connector type	LC
	Fiber count	Single
	Transmitter wavelength	1550 nm
	Receiver wavelength	1310 nm
	Minimum launch power	–9 dBm
	Maximum launch power	–3 dBm
	Minimum receiver sensitivity	–21 dBm
	Maximum input power	–3 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 μm
	Modal bandwidth	–
	Distance	10 km (6.2 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
1000BASE-BX-U	Model number	EX-SFP-GE40KT13R15
	Rate	1000 Mbps
	Connector type	LC
	Fiber count	Single
	Transmitter wavelength	1310 nm
	Receiver wavelength	1550 nm
	Minimum launch power	–6.5 dBm
	Maximum launch power	2 dBm
	Minimum receiver sensitivity	–23 dBm
	Maximum input power	–3 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 μm
	Modal bandwidth	–
	Distance	40 km (24.85 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
1000BASE-BX-D	Model number	EX-SFP-GE40KT15R13
	Rate	1000 Mbps
	Connector type	LC
	Fiber count	Single
	Transmitter wavelength	1550 nm
	Receiver wavelength	1310 nm
	Minimum launch power	–6.5 dBm
	Maximum launch power	2 dBm
	Minimum receiver sensitivity	–23 dBm
	Maximum input power	–3 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 μm
	Modal bandwidth	–
	Distance	40 km (24.85 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
1000BASE-LX	Model number	EX-SFP-1GE-LX40K
	Rate	1000 Mbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	1310 nm
	Minimum launch power	–14 dBm
	Maximum launch power	–8 dBm
	Minimum receiver sensitivity	–45 dBm
	Maximum input power	–3 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 µm
	Modal bandwidth	–
	Distance	40 km (24.85 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
1000BASE-LH (or 1000BASE-ZX)	Model number	EX-SFP-1GE-LH
	Rate	1000 Mbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	1550 nm
	Minimum launch power	–2 dBm
	Maximum launch power	5 dBm
	Minimum receiver sensitivity	–25 dBm
	Maximum input power	–3 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 µm
	Modal bandwidth	–
	Distance	70 km (43.5 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later

Table 9: Optical Interface Support for Fast Ethernet and Fast Ethernet SFP Transceivers in EX9200 Switches

Ethernet Standard	Specification	Value
100BASE-FX	Model number	EX-SFP-1FE-FX
	Rate	100 Mbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	1310 nm
	Minimum launch power	–20 dBm
	Maximum launch power	–14 dBm
	Minimum receiver sensitivity	–32.5 dBm
	Maximum input power	–8 dBm
	Fiber type	MMF
	Core/Cladding size	62.5/125 µm	50/125 µm
	Fiber grade	FDDI/OM1	OM2
	Modal bandwidth	500 MHz/km	–
	Distance	2 km (1.2 miles)	2 km (1.2 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
100BASE-BX-U	Model number	EX-SFP-FE20KT13R15
	Rate	100 Mbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	1310 nm
	Receiver wavelength	1550 nm
	Minimum launch power	–14 dBm
	Maximum launch power	–8 dBm
	Minimum receiver sensitivity	–45 dBm
	Maximum input power	–8 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 µm
	Modal bandwidth	–
	Distance	20 km (12.4 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
100BASE-BX-D	Model number	EX-SFP-FE20KT15R13
	Rate	100 Mbps
	Connector type	LC
	Fiber count	Single
	Transmitter wavelength	1550 nm
	Receiver wavelength	1310 nm
	Minimum launch power	–14 dBm
	Maximum launch power	–8 dBm
	Minimum receiver sensitivity	–45 dBm
	Maximum input power	–8 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 µm
	Modal bandwidth	–
	Distance	20 km (12.4 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later

Table 10: Optical Interface Support for SFP+ Transceivers in EX9200 Switches

Ethernet Standard	Specification	Value
10GBASE-USR	Model number	EX-SFP-10GE-USR
	Rate	10 Gbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	850 nm
	Minimum launch power	–7.3 dBm
	Maximum launch power	–1.3 dBm
	Minimum receiver sensitivity	–11.1 dBm
	Maximum input power	–1.0 dBm
	Fiber type	MMF
	Core/Cladding size	62.5/125 µm	50/125 µm	50/125 µm
	Fiber grade	OM1	OM3	OM3
	Modal bandwidth	200 MHz/km	500 MHz/km	1500 MHz/km
	Distance	10 m (32.8 ft)	30 m (98.4 ft)	100 m (328 ft)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
10GBASE-SR	Model number	EX-SFP-10GE-SR
	Rate	10 Gbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	850 nm
	Minimum launch power	–7.3 dBm
	Maximum launch power	–1 dBm
	Minimum receiver sensitivity	–9.9 dBm
	Maximum input power	–1 dBm
	Fiber type	MMF
	Core/Cladding size	62.5/125 µm	62.5/125 µm	50/125 µm	50/125 µm	50/125 µm
	Fiber grade	FDDI	OM1	–	OM2	OM3
	Modal bandwidth	160 MHz/km	200 MHz/km	400 MHz/km	500 MHz/km	1500 MHz/km
	Distance	26 m (85 ft)	33 m (108 ft)	66 m (216 ft)	82 m (269 ft)	300 m (984 ft)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
10GBASE-LRM	Model number	EX-SFP-10GE-LRM
	Rate	10 Gbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	1310 nm
	Minimum launch power	–6.5 dBm
	Maximum launch power	0.5 dBm
	Minimum receiver sensitivity	–21 dBm
	Maximum input power	0.5 dBm
	Fiber type	MMF
	Core/Cladding size	62.5/125 µm		50/125 µm		50/125 µm
	Fiber grade	FDDI/OM1		OM2		OM3
	Modal bandwidth	500 MHz/km		500 MHz/km		500 MHz/km
	Distance	220 m (722 ft)		220 m (722 ft)		220 m (722 ft)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 16.1R1 or later
	Support for Virtual Chassis configuration	No
10GBASE-LR	Model number	EX-SFP-10GE-LR
	Rate	10 Gbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	1310 nm
	Minimum launch power	–8.2 dBm
	Maximum launch power	0.5 dBm
	Minimum receiver sensitivity	–18 dBm
	Maximum input power	0.5 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 µm
	Modal bandwidth	–
	Distance	10 km (6.2 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
10GBASE-ER	Model number	EX-SFP-10GE-ER
	Rate	10 Gbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	1550 nm
	Minimum launch power	–4.7 dBm
	Maximum launch power	4 dBm
	Minimum receiver sensitivity	–11.3 dBm
	Maximum input power	–1 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 µm
	Modal bandwidth	–
	Distance	40 km (24.8 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
10GBASE-ZR	Model number	EX-SFP-10GE-ZR
	Rate	10 Gbps
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	1550 nm
	Minimum launch power	0 dBm
	Maximum launch power	5 dBm
	Minimum receiver sensitivity	–20 dBm
	Maximum input power	–8 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 µm
	Modal bandwidth	–
	Distance	80 km (49.7 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later

Table 11: Optical Interface Support for 40-Gigabit QSFP+ Transceivers in EX9200 Switches

Ethernet Standard	Specification	Value
40GBASE-SR4	Model number	QFX-QSFP-40GE-SR4, QSFP+-40G-SR4, or QSFP+-4X10G-SR
	Rate	40 Gbps (10 Gbps per lane)
	Connector type	12-ribbon multimode fiber crossover cable with female MTP connectors
	Fiber count	12
	Transmitter wavelength	850 nm
	Minimum launch power	–7.6 dBm
	Maximum launch power	2.4 dBm
	Maximum receiver sensitivity	– 5.4 dBm
	Maximum input power	4 dBm
	Fiber type	MMF
	Core/Cladding size	50/125 µm	50/125 µm
	Fiber grade	OM3	OM4
	Modal bandwidth	2000 MHz/km	4700 MHz/km
	Distance	100 m (328 ft)	150 m (492 ft)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later
40GBASE-LX4	Model number	JNP-QSFP-40G-LX4
	Rate	40 Gbps (10 Gbps per lane)
	Connector type	Dual LC
	Fiber count	Dual
	Lane wavelength	Lane 0–1271 nm Lane 1–1291 nm Lane 2–1311 nm Lane 3–1331 nm
	Minimum launch power	-7.0 dBm (per lane)
	Maximum launch power	4.3 dBm (per lane)
	Maximum power draw	3.5 W
	Fiber type	MMF	MMF
	Core/Cladding size	50/125 µm	50/125 µm
	Fiber grade	OM3	OM4
	Modal bandwidth	2000 MHz/km	4700 MHz/km
	Distance	100 m (328 ft)	150 m (492 ft)
	DOM support	Available
	Support for Virtual Chassis configuration	Yes
	Software required	Junos OS for EX Series switches, Release 15.1 R3 or later
40GBASE-LR4	Model number	JNP-QSFP-40G-LR4, QSFP+-40G-LR4, or QSFP+-4X10G-LR
	Rate	40 Gbps (10 Gbps per lane)
	Connector type	LC
	Fiber count	Dual
	Transmitter wavelength	1264.5 nm through 1277.5 nm 1284.5 nm through 1297.5 nm 1304.5 nm through 1317.5 nm 1324.5 nm through 1337.5 nm
	Minimum launch power	–7.0 dBm
	Maximum launch power	2.3 dBm
	Maximum receiver sensitivity	– 11.5 dBm
	Maximum input power	3.3 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 µm
	Distance	10 km (6.2 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 12.3R2 or later

Table 12: Optical Interface Support for 100-Gigabit QSFP+ Transceivers in EX9200 Switches

Ethernet Standard	Specification	Value
100GBASE-SR4	Model number	QSFP-100GBASE-SR4
	Rate	100 Gbps
	Connector type	MPO
	Transmitter wavelength	840 nm through 860 nm
	Average launch power per lane	–8.4 dBm through 2.4 dBm
	Average receive power per lane	–10.3 dBm through 2.4 dBm
	Fiber type	MMF
	Fiber grade	OM3	OM4
	Distance	70 m (230 ft)	100 m (328 ft)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 16.1R1 or later
100GBASE-LR4	Model number	QSFP-100GBASE-LR4
	Rate	100 Gbps
	Connector type	LC
	Transmitter wavelength per lane	1294.53 nm through 1296.59 nm 1299.02 nm through 1301.09 nm 1303.54 nm through 1305.63 nm 1308.09 nm through 1310.19 nm
	Average launch power per lane	–4.3 dBm through 4.5 dBm
	Average receive power per lane	–10.6 dBm through 4.5 dBm
	Fiber type	SMF
	Distance	10 km (6.2 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 16.1R1 or later

Table 13: Optical Interface Support for CFP Transceivers in EX9200 Switches

Ethernet Standard	Specification	Value
100GBASE-SR10	Model number	CFP-100GBASE-SR10
	Optical interface	Multimode
	Rate	100 Gbps
	Standard	IEEE 802.3ba—2010
	Transmitter wavelength	840 nm through 860 nm
	Average launch power	–7.6 dBm through 2.4 dBm
	Average receive power	–9.5 dBm through 2.4 dBm for OM3 –9.1 dBm through 2.4 dBm for OM4
	Receiver saturation	2.4 dBm
	Receiver sensitivity	–9.5 dBm for OM3 –9.1 dBm for OM4
	Fiber type	MMF
	Fiber grade	OM3
	Distance	100 m (328 ft)
	DOM support	Not available
	Software required	Junos OS for EX Series switches, Release 13.2R1 or later
100GBASE-LR4	Model number	CFP-GEN2-100GBASE-LR4
	Optical interface	Single-mode
	Rate	100 Gbps
	Standard	IEEE 802.3ba-2010
	Transmitter wavelength	1294.53 nm through 1296.59 nm 1299.02 nm through 1301.09 nm 1303.54 nm through 1305.63 nm 1308.09 nm through 1310.19 nm
	Average launch power	–4.3 dBm through 4.5 dBm
	Maximum launch power	10.5 dBm
	Average receive power	–10.6 dBm through 4.5 dBm
	Receiver saturation	4.5 dBm
	Receiver sensitivity	–10.6 dBm
	Fiber type	SMF
	Core/Cladding size	9/125 µm
	Distance	10 km (6.2 miles)
	DOM support	Available
	Software required	Junos OS for EX Series switches, Release 13.2R1 or later

TechLibrary

Download This Guide

Related Documentation

Pluggable Transceivers Supported on EX9200 Switches

Related Documentation

Modified: 2016-08-25