[ Contents] [ Prev] [ Next] [ Report an Error]

4-Port 10-Gigabit Ethernet Enhanced Ethernet Services DPC with XFP

Image g002602.gif

Software release

  • JUNOS 8.4 and later

Description

  • Four 10-Gigabit Ethernet ports
  • Power requirement: 6.46 A @ 48 V (310 W)
  • Weight: 13.1 lb (5.9 kg)

Hardware features

  • High-performance throughput on each port at speeds up to 10 Gbps
  • WAN-PHY mode at 9.953 Gbps
  • LAN-PHY mode at 10.3125 Gbps
  • Full-duplex mode
  • Maximum transmission units (MTUs) of up to 9192 bytes
  • Enhanced ASICs for increased performance and scalability of Layer 2 features

Software features

Note: The routing table is limited to 32,000 IP routes. This limitation applies to any manner in which the routes are learned, such as OSPF, RIP, and so on. The DPC supports BGP for L2 VPNs only.

Cables and connectors

  • You can install any transceiver supported by the DPC. For information about installing and removing transceivers, see the hardware guide for your router.
  • Fiber-optic SX, LX, and LH 10-gigabit small form-factor pluggable (XFP) transceivers:
    • Duplex LC/PC connector (Rx and Tx)
    • Optical interface support—See Table 5

LEDs

OK/FAIL LED, one bicolor:

  • Green—DPC is functioning normally.
  • Red—DPC has failed.

Tunnel LED, one green per port:

  • Off—Normal operating mode.
  • On steadily—Port configured in tunnel mode.

Link LED, one green per port:

  • Off—No link.
  • On steadily—Link is active.

The Tunnel and Link LEDs are labeled top to bottom 0/0 through 3/0.

Table 5: Optical Interface for the 4-Port 10-Gigabit Ethernet Enhanced Ethernet Services DPC

Parameter

10-GBASE-S

10-GBASE-L

10-GBASE-E

10-GBASE-Z

Transceiver model number

XFP-10G-S

XFP-10G-L-OC192-SR1

XFP-10G-E-OC192-IR2

XFP-10G-Z-OC192-LR2

Optical interface

Multimode

Single-mode

Single-mode

Single-mode

Transceiver type

XFP

XFP

XFP

XFP

Standard

IEEE 802.3ae—2002

IEEE 802.3ae—2002

IEEE 802.3ae—2002

Multivendor agreement

Maximum distance

50/125 MMF cable, 2000 MHz-km: 984 feet/300 m

50/125 MMF cable, 500 MHz-km: 269 feet/82 m

50/125 MMF cable, 400 MHz-km: 217 feet/66 m

62.5/125 MMF cable, 200 MHz-km: 108 feet/33 m

62.5/125 MMF cable, 160 MHz-km: 85 feet/26 m

9/125 SMF cable: 6.2 miles/10  km

9/125 SMF cable: 24.8 miles/40 km: Distances greater than 30 km are considered to be engineered links.

9/125 SMF cable: 49.6 miles/80 km

Transmitter wavelength

840 through 860 nm

1260 through 1355 nm

1530 through 1565 nm

1530 through 1565 nm

Average launch power

–4.5 through –1 dBm

–8.2 through .5 dBm

–4.7 through 4 dBm

0 through 4 dBm

Average receive power

–9.9 through –1.0  dBm

–14.4 through 0.5  dBm

–15.8 through –1.0  dBm

–24.0 through –7.0  dBm

Receiver saturation

–1.0 dBm

0.5 dBm

–1.0 dBm

–7 dBm

Receiver sensitivity

–9.9 dBm

–14.4 dBm

–15.8 dBm

–24 dBm


[ Contents] [ Prev] [ Next] [ Report an Error]