[ Contents] [ Prev] [ Next] [ Report an Error]

ATM2 OC12/STM4 IQ PIC (M10i Router)

Image g001365.gif

Software release

  • JUNOS 6.0 and later


  • One OC12 port
  • Power requirement: 0.41 A @ 48 V (20 W)
  • Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface
  • Conforms to ANSI T1.105-1991 and T1E1.2/93-020R1
  • Complies with ATM and SONET/SDH standards
  • Alarm and event counting and detection
  • Compatible with well-known ATM switches
  • ATM switch ID, which displays the switch IP address and local interface name of the adjacent Fore ATM switches

Hardware features

  • One 3010 SAR for segmentation and reassembly into 53-byte ATM cells
  • High-performance parsing of SONET/SDH frames
  • ASIC-based packet segmentation and reassembly (SAR) management and output port queuing
  • 64 MB SDRAM memory for ATM SAR
  • Packet buffering, Layer 2 parsing

Software features

  • Circuit cross-connect for leveraging ATM access networks
  • User-configurable virtual circuit (VC) and virtual path (VP) support
  • Support for idle cell or unassigned cell transmission
  • OAM fault management processes alarm indication signal (AIS), remote defect indication (RDI), and loop cells
  • Point-to-point and point-to-multipoint mode Layer 2 counters per VC and per VP
  • Local and remote loopback
  • ATM Inverse ARP, which enables routers to automatically learn the IP address of the router on the far end of an ATM PVC
  • Simple Network Management Protocol (SNMP):
    • Management Information Base (MIB) 2 (RFC 1213)
    • ATM MIB (RFC 1695)
  • Unspecified bit rate (UBR), non-real-time variable bit rate (VBR), and constant bit rate (CBR) traffic shaping
  • Per-VC or per-VP traffic shaping
  • Support for F4 OAM cells
  • Support for 16-bit VCI range

Cables and connectors

  • Duplex SC/PC connector (Rx and Tx)
  • Optical interface support—See Table 3


One tricolor per port:

  • Off—Not enabled
  • Green—Online with no alarms or failures
  • Amber—Online with alarms for remote failures
  • Red—Active with a local alarm; router has detected a failure

Alarms, errors, and events

  • Alarm indication signal (AIS-L, AIS-P)
  • Bit error rate signal degrade (BERR-SD), bit error rate signal fail (BERR-SF)
  • Bit interleaved parity errors B1, B2, B3
  • Errored seconds (ES-S, ES-L, ES-P), far-end bit errors REI-L, REI-P (CV-LFE, CV-PFE), far-end errored seconds (ES-LFE, ES-PFE), far-end severely errored seconds (SES-LFE, SES-PFE), far-end unavailable seconds (UAS-LFE, UAS-PFE)
  • Loss of cell delineation (LOC), loss of frame (LOF), loss of pointer (LOP-P), loss of signal (LOS)
  • Payload mismatch (PLM-P), payload unequipped (UNEQ-P)
  • Remote defect indication (RDI-L, RDI-P)
  • Severely errored framing (SEF), severely errored framing seconds (SEFS-S), severely errored seconds (SES-S, SES-L, SES-P), unavailable seconds (UAS-L, UAS-P)

[ Contents] [ Prev] [ Next] [ Report an Error]