Configuring ARP

Adding a Static Entry in the ARP Cache

You can add a static (permanent) entry in the ARP cache using the arp command.

You can specify the ipAddress, interfaceType and interfaceSpecifier (as indicated in Interface Types and Specifiers in JunosE Command Reference Guide ), and an optional MAC address.

To add a static entry in the ARP cache:

• Issue the arp command in Global Configuration mode.
  host1(config)#arp 192.56.20.1 gig 2/0 0090.1a00.0170

  Note: You can issue this command only for Fast Ethernet interfaces, Gigabit Ethernet interfaces, 10-Gigabit Ethernet interfaces, and bridged Ethernet interfaces configured over ATM 1483.

  Use the no version to remove an entry from the ARP cache.

Checking for Spoofed ARP Packets

You can configure the router to check for spoofed ARP packets received on an IP interface or an IP subinterface using the arp spoof-check command.

By default, E Series routers check all received ARP packets for spoofing and process only those ARP packets whose source IP address is outside the range of the network mask. ARP packets with a source IP address of 0.0.0.0 and the router IP address as the destination address are dropped because the router identifies them as spoofed packets.

In networks with digital subscriber line access multiplexers (DSLAMs), even if you configure the router to check for spoofed ARP packets, DSLAMs perform this task instead of the router. If you disable checking for spoofed ARP packets on the router in such networks, DSLAMs forward the received packets to the router for processing. You can, therefore, configure the router accordingly, depending on the way in which you want spoof-checking to be performed.

You cannot configure ARP spoof-checking on interfaces that do not support ARP, such as loopback interfaces and ATM point-to-point PVCs.

If you disable checking for spoofed ARP packets, all packets received by the router are processed. You can reenable checking for spoofed ARP packets on an interface at any time by using the arp spoof-check command after disabling it.

Before you configure IP, you must create the lower-layer interfaces over which IP traffic flows. All IP configurations will be removed from the interface when you issue the no ip interface command in Interface Configuration mode.

To enable spoof-checking for ARP packets received on an interface:

• Issue the arp spoof-check command in Interface Configuration mode.
  host1(config-if)#arp spoof-check

  Use the no version to disable checking for spoofed ARP packets received on a major IP interface or an IP subinterface.

Configuring ARP Cache Entry Timeout

You can specify how long an entry remains in the ARP cache using the arp timeout command. The default value is 21,600 seconds (6 hours). You can use the show config command to display the current value. If you specify a timeout of 0 seconds, entries are never cleared from the ARP cache.

Before you configure IP, you must create the lower-layer interfaces over which IP traffic flows. All IP configurations will be removed from the interface when you issue the no ip interface command in Interface Configuration mode.

To specify how long an entry remains in the ARP cache:

• Issue the arp timeout command in Interface Configuration mode.
  host1(config-if)#arp timeout 8000

  Note: You can issue this command only for Fast Ethernet interfaces, Gigabit Ethernet interfaces, 10-Gigabit Ethernet interfaces, and bridged Ethernet interfaces configured over ATM 1483.

  Use the no version to restore the default value.

Clearing Dynamic Entries from the ARP Cache

You can clear a particular dynamic entry from the ARP cache using the clear arp command by specifying all of the following options:

• ipAddress—IP address in four-part dotted-decimal format corresponding to the local data link address
• interfaceType—Interface type; see Interface Types and Specifiers in JunosE Command Reference Guide
• interfaceSpecifier—Particular interface; format varies according to interface type; see Interface Types and Specifiers in JunosE Command Reference Guide

You can clear all dynamic entries from the ARP cache using the clear arp command with an asterisk (*).

To clear all dynamic entries:

• Issue the clear arp command with an asterisk (*) in Privileged Exec mode.
  host1#clear arp