LM-10 Line Module

Module label ES2 10G LM
Number of ports
Not applicable
Software release
First supported: 8.0.0
Description
198 W maximum
Acts as frame forwarding engines for the physical interfaces
Processes up to 10 Gb of data traffic
Pairs with ES2–S2 10GE PR IOA and ES2–S1 GE-8 IOA
In a SRP-100 configuration, it must be installed in a turbo slot only (slot 2 or slot 4)
If you install the line module in a slot other than slot 2 or slot 4, it will be disabled
If you install the LM-10 module next to a configured line module that is already installed in slot 3 or slot 5, the LM-10 module will be disabled
If you install a line module in slot 3 or slot 5 next to a previously installed LM-10 module, the non-LM-10 module will be disabled
In a SRP-120 and SRP-320 configuration, it can be installed in any slot
Type
TFA ASIC
Capability
Supports a line rate of 128–byte frames on IOAs
The 100–Gbps switch fabric allocates 3.4 Gbps of overall bandwidth to each regular line module slot and 10 Gbps of overall bandwidth to each of the turbo slots (slot 2 and slot 4).
The 120–Gbps and 320–Gbps switch fabrics allocate 10 Gbps of overall bandwidth to each line module slot.
See JunosE System Basics Configuration Guide, Chapter 6, Managing Modules for more information.
Software features
Not applicable
Line module compatibility
Not applicable
SRP module compatibility
SRP-100
SRP-120
SRP-320
Line module redundancy compatibility
Yes (Redundancy IOA must be installed in either slot 0 or slot 11)
Can only back up another ES2 10G LM
Port redundancy support
Not applicable
Cables and connectors
Not applicable
LEDs When lit, LED indicates:
OK (green)—Self-test passed
FAIL (red)—Failure detected
ONLINE (green)—Online with no alarms or errors
REDUN (green)—Redundant card available
Alarms, errors, and events
See Monitoring Modules in JunosE System Basics Configuration Guide, Chapter 6, Managing Modules.

Module label	ES2 10G LM
Number of ports	Not applicable
Software release	First supported: 8.0.0
Description	198 W maximum Acts as frame forwarding engines for the physical interfaces Processes up to 10 Gb of data traffic Pairs with ES2–S2 10GE PR IOA and ES2–S1 GE-8 IOA In a SRP-100 configuration, it must be installed in a turbo slot only (slot 2 or slot 4) If you install the line module in a slot other than slot 2 or slot 4, it will be disabled If you install the LM-10 module next to a configured line module that is already installed in slot 3 or slot 5, the LM-10 module will be disabled If you install a line module in slot 3 or slot 5 next to a previously installed LM-10 module, the non-LM-10 module will be disabled In a SRP-120 and SRP-320 configuration, it can be installed in any slot
Type	TFA ASIC
Capability	Supports a line rate of 128–byte frames on IOAs The 100–Gbps switch fabric allocates 3.4 Gbps of overall bandwidth to each regular line module slot and 10 Gbps of overall bandwidth to each of the turbo slots (slot 2 and slot 4). The 120–Gbps and 320–Gbps switch fabrics allocate 10 Gbps of overall bandwidth to each line module slot. See JunosE System Basics Configuration Guide, Chapter 6, Managing Modules for more information.
Software features	Not applicable
Line module compatibility	Not applicable
SRP module compatibility	SRP-100 SRP-120 SRP-320
Line module redundancy compatibility	Yes (Redundancy IOA must be installed in either slot 0 or slot 11) Can only back up another ES2 10G LM
Port redundancy support	Not applicable
Cables and connectors	Not applicable
LEDs	When lit, LED indicates: OK (green)—Self-test passed FAIL (red)—Failure detected ONLINE (green)—Online with no alarms or errors REDUN (green)—Redundant card available
Alarms, errors, and events	See Monitoring Modules in JunosE System Basics Configuration Guide, Chapter 6, Managing Modules.