[Contents][Prev][Next][Report an Error]

OC3/STM1 GE/FE Module Combination

Line module label OC3/STM1 GE/FE

I/O module label OC3-2 GE APS I/O

Number of I/O ports

3; one active and one redundant port per SFP

Ports 0 and 1—ATM interfaces

Port 2—GE interface

Port redundancy is not supported.

Software release

First supported: 6.1.0

Final supported: Not applicable

Description

150 W

Unchannelized OC3/STM1 ATM operation via two line interfaces
and

Gigabit Ethernet operation via one line interface

The I/O module uses a range of small form-factor pluggable (SFP) transceivers to support different modes and cabling distances.

Depending on the configuration, a variety of SFP combinations can occur.

The OC3-2 GE APS I/O module accepts up to three LC-style fiber-optic or copper SFPs.

Type

ASIC

Capability

OC3/STM1

ATM/AAL5

Ethernet (IEEE 802.3x)

1000Base-LX/SX/ZX

Software features

See OCx/STMx GE/FE Modules for information about the layer 2 and layer 3 protocols and applications that this module combination supports.

Model compatibility

ERX-7xx models

ERX-14xx models

ERX-310 router

SRP module compatibility

SRP-5G+

SRP-10G

SRP-40G

SRP-40G PLUS

SRP-SE10G

Module redundancy support

Not applicable

Cables and connectors (ATM LX)

LC-style fiber-optic connectors

Tx power:

min: –19.0 dBm

max: –14dBm

Center wavelength: 1310 nm

Rx input power:

min: –30 dBm

max: –14 dBm

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9db or over 50-micron core cable with an optical loss of 7 db

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

Cables and connectors (ATM SX)

LC-style fiber-optic connectors

Tx power:

min: –15.0 dBm

max: –8 dBm

Center wavelength: 1310 nm

Rx input power:

min: –31 dBm

max: –8 dBm

Rated for 15 km (9.3 miles) of 9-micron core cable

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

Cables and connectors (ATM ZX)

LC-style fiber-optic connectors

Tx power:

min: –5.0 dBm

max: 0 dBm

Center wavelength: 1310 nm

Rx input power:

min: –34 dBm

max: –7 dBm

Rated for 40 km (24.8 miles) of 9-micron core cable

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

Cables and connectors (GE LX)

LC full duplex

Tx power:

min: –9.5 dBm

max: –3 dBm

Center wavelength: 1300 nm

Rx input power:

min: –20 dBm

max: –3 dBm

Rated for 10 km (6.2 miles) over 10-micron core cable

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

Cables and connectors (GE single–mode LX40)

LC full duplex

Tx power:

min: –4.5 dBm

max: –0 dBm

Center wavelength: 1300 nm

Rx input power:

min: –35 dBm

max: –22.5 dBm

Rated for 40 km (28.85 miles) over 9-micron core cable

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

Cables and connectors (GE SX)

LC full duplex

Tx power:

min: –9.5 dBm

max: –4 dBm

Center wavelength: 850 nm

Rx input power:

min: –17 dBm

max: –3 dBm

Rated for 275 m (300 yards) over 62.5-micron core cable

Rated for 550 m (601 yards) over 50-micron core cable

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

Cables and connectors (GE ZX)

LC full duplex

Tx power:

min: –3 dBm

max: 2 dBm

Center wavelength: 1550 nm

Rx input power:

min: –23 dBm

max: –3 dBm

Rated for 70 km (43.4 miles) over 10-micron core cable

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

LEDs

See Module LEDs.

Alarms, errors, and events

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

[Contents][Prev][Next][Report an Error]

Line module label	OC3/STM1 GE/FE
I/O module label	OC3-2 GE APS I/O
Number of I/O ports	3; one active and one redundant port per SFP Ports 0 and 1—ATM interfaces Port 2—GE interface Port redundancy is not supported.
Software release	First supported: 6.1.0 Final supported: Not applicable
Description	150 W Unchannelized OC3/STM1 ATM operation via two line interfaces and Gigabit Ethernet operation via one line interface The I/O module uses a range of small form-factor pluggable (SFP) transceivers to support different modes and cabling distances. Depending on the configuration, a variety of SFP combinations can occur. The OC3-2 GE APS I/O module accepts up to three LC-style fiber-optic or copper SFPs.
Type	ASIC
Capability	OC3/STM1 ATM/AAL5 Ethernet (IEEE 802.3x) 1000Base-LX/SX/ZX
Software features	See OCx/STMx GE/FE Modules for information about the layer 2 and layer 3 protocols and applications that this module combination supports.
Model compatibility	ERX-7xx models ERX-14xx models ERX-310 router
SRP module compatibility	SRP-5G+ SRP-10G SRP-40G SRP-40G PLUS SRP-SE10G
Module redundancy support	Not applicable
Cables and connectors (ATM LX)	LC-style fiber-optic connectors Tx power: min: –19.0 dBm max: –14dBm Center wavelength: 1310 nm Rx input power: min: –30 dBm max: –14 dBm Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9db or over 50-micron core cable with an optical loss of 7 db See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors (ATM SX)	LC-style fiber-optic connectors Tx power: min: –15.0 dBm max: –8 dBm Center wavelength: 1310 nm Rx input power: min: –31 dBm max: –8 dBm Rated for 15 km (9.3 miles) of 9-micron core cable See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors (ATM ZX)	LC-style fiber-optic connectors Tx power: min: –5.0 dBm max: 0 dBm Center wavelength: 1310 nm Rx input power: min: –34 dBm max: –7 dBm Rated for 40 km (24.8 miles) of 9-micron core cable See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors (GE LX)	LC full duplex Tx power: min: –9.5 dBm max: –3 dBm Center wavelength: 1300 nm Rx input power: min: –20 dBm max: –3 dBm Rated for 10 km (6.2 miles) over 10-micron core cable See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors (GE single–mode LX40)	LC full duplex Tx power: min: –4.5 dBm max: –0 dBm Center wavelength: 1300 nm Rx input power: min: –35 dBm max: –22.5 dBm Rated for 40 km (28.85 miles) over 9-micron core cable See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors (GE SX)	LC full duplex Tx power: min: –9.5 dBm max: –4 dBm Center wavelength: 850 nm Rx input power: min: –17 dBm max: –3 dBm Rated for 275 m (300 yards) over 62.5-micron core cable Rated for 550 m (601 yards) over 50-micron core cable See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors (GE ZX)	LC full duplex Tx power: min: –3 dBm max: 2 dBm Center wavelength: 1550 nm Rx input power: min: –23 dBm max: –3 dBm Rated for 70 km (43.4 miles) over 10-micron core cable See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
LEDs	See Module LEDs.
Alarms, errors, and events	See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.