[Contents] [Prev] [Next] [Report an Error]

SONET/SDH OC48c/STM16 PIC

Image g001351.gif

Software release

JUNOS 3.1 and later

Description

One OC48 port

Power requirements: 0.86 A/48 V @ 41.4 W

Optical interface support—see Table 6

Note: On the M5, M10, M20, M40, and M160 routers, this PIC requires an enhanced FPC. See the hardware guide for your router for more information.

Hardware features

Multiplexing and demultiplexing

Rate policing on input

Rate shaping on output

Packet buffering, Layer 2 parsing

Software features

SONET/SDH framing

Alarm and event counting and detection

Dual-router automatic protection switching (APS)

Multiprotocol Label Switching (MPLS) fast reroute

Link aggregation

Encapsulations:

High-level Data Link Control (HDLC)

Frame Relay

Multiprotocol Label Switching (MPLS) circuit cross-connect (CCC)

Point-to-Point Protocol (PPP)

Cables and connectors

Duplex LC/PC connector (RX and TX)

LEDs One tricolor per port:

Off—Not enabled

Green—Online with no alarms or failures

Amber—Online with alarms for remote failures

Red—Active with a local alarm; router has detected a failure

Alarms, errors, and events

Alarm Indication Signal (AIS-L, AIS-P)

Bit Error Rate Signal Degrade (BERR-SD), Bit Error Rate Signal Fail (BERR-SF)

Bit Interleaved Parity Errors B1, B2, B3 (CV-S, CV-L, CV-P)

Errored Seconds (ES-S, ES-L, ES-P), Far-end Bit Errors REI-L, REI-P (CV-LFE, CV-PFE), Far-end Errored Seconds (ES-LFE, ES-PFE), Far-end Severely Errored Seconds (SES-LFE, SES-PFE), Far-end Unavailable Seconds (UAS-LFE, UAS-PFE)

Loss of Frame (LoF), Loss of Pointer (LoP-P), Loss of Signal (LoS)

Payload Mismatch (PLM-P), Payload Unequipped (UNEQ-P)

Remote Defect Indication (RDI-L, RDI-P)

Severely Errored Framing (SEF), Severely Errored Framing Seconds (SEFS-S), Severely Errored Seconds (SES-S, SES-L, SES-P), Unavailable Seconds (UAS-L, UAS-P)

Table 6: Optical Interface Support for SONET/SDH OC48c/STM16 PICs

PIC Type Single-mode Short Reach (SR) Single-mode Intermediate Reach (IR) Single-mode Long Reach (LR)

Optical interface Single-mode short reach (Bellcore GR-253 compliant) optical interface (maximum distance 1.24 miles/2 km) Single-mode intermediate reach (Bellcore GR-253 compliant) optical interface (maximum distance 9.3 miles/15 km) Single-mode long reach (Bellcore GR-253 compliant) optical interface (maximum distance 49.71 miles/80 km); compatible with 1550 nm single-mode LR

Wavelength 1266 through 1360 nm 1260 through 1360 nm 1500 through 1580 nm

Average launch power –11 through –3 dBm –5 through 0 dBm –2 through +3 dBm

Receiver saturation 0 dBm 0 dBm –9 dBm

Receiver sensitivity –18 dBm –18 dBm –28 dBm

PIC Type	Single-mode Short Reach (SR)	Single-mode Intermediate Reach (IR)	Single-mode Long Reach (LR)
Optical interface	Single-mode short reach (Bellcore GR-253 compliant) optical interface (maximum distance 1.24 miles/2 km)	Single-mode intermediate reach (Bellcore GR-253 compliant) optical interface (maximum distance 9.3 miles/15 km)	Single-mode long reach (Bellcore GR-253 compliant) optical interface (maximum distance 49.71 miles/80 km); compatible with 1550 nm single-mode LR
Wavelength	1266 through 1360 nm	1260 through 1360 nm	1500 through 1580 nm
Average launch power	–11 through –3 dBm	–5 through 0 dBm	–2 through +3 dBm
Receiver saturation	0 dBm	0 dBm	–9 dBm
Receiver sensitivity	–18 dBm	–18 dBm	–28 dBm

[Contents] [Prev] [Next] [Report an Error]

Description	One OC48 port Power requirements: 0.86 A/48 V @ 41.4 W Optical interface support—see Table 6 Note: On the M5, M10, M20, M40, and M160 routers, this PIC requires an enhanced FPC. See the hardware guide for your router for more information.
Hardware features	Multiplexing and demultiplexing Rate policing on input Rate shaping on output Packet buffering, Layer 2 parsing
Software features	SONET/SDH framing Alarm and event counting and detection Dual-router automatic protection switching (APS) Multiprotocol Label Switching (MPLS) fast reroute Link aggregation Encapsulations: High-level Data Link Control (HDLC) Frame Relay Multiprotocol Label Switching (MPLS) circuit cross-connect (CCC) Point-to-Point Protocol (PPP)
Cables and connectors	Duplex LC/PC connector (RX and TX)
LEDs	One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local alarm; router has detected a failure
Alarms, errors, and events	Alarm Indication Signal (AIS-L, AIS-P) Bit Error Rate Signal Degrade (BERR-SD), Bit Error Rate Signal Fail (BERR-SF) Bit Interleaved Parity Errors B1, B2, B3 (CV-S, CV-L, CV-P) Errored Seconds (ES-S, ES-L, ES-P), Far-end Bit Errors REI-L, REI-P (CV-LFE, CV-PFE), Far-end Errored Seconds (ES-LFE, ES-PFE), Far-end Severely Errored Seconds (SES-LFE, SES-PFE), Far-end Unavailable Seconds (UAS-LFE, UAS-PFE) Loss of Frame (LoF), Loss of Pointer (LoP-P), Loss of Signal (LoS) Payload Mismatch (PLM-P), Payload Unequipped (UNEQ-P) Remote Defect Indication (RDI-L, RDI-P) Severely Errored Framing (SEF), Severely Errored Framing Seconds (SEFS-S), Severely Errored Seconds (SES-S, SES-L, SES-P), Unavailable Seconds (UAS-L, UAS-P)