[Contents] [Prev] [Next] [Report an Error]

ATM OC3 PIC

Image g003054.gif

Software release

JUNOS 3.1 and later

Description

Two OC3 ports

Power requirements: 0.49 A/48 V @ 23.7 W

Conforms to ANSI T1.105-1991 and T1E1.2/93-020R1

ATM and SONET/SDH standards compliant

Alarm and event counting and detection

Compatible with well-known ATM switches

ATM switch ID, which displays the switch IP address and local interface name of the adjacent Fore ATM switches

Optical interface support—see Table 2

Hardware features

Dual 3010 SAR for segmentation and reassembly into 53-byte ATM cells

High-performance parsing of SONET/SDH frames

OAM fault management processes Alarm Indication Signal (AIS) and Remote Defect Indicator (RDI) cells

ASIC-based packet segmentation and reassembly (SAR) management and output port queuing

16-MB SDRAM memory for ATM SAR

Packet buffering, Layer 2 parsing

Software features

Multiprotocol Label Switching (MPLS) circuit cross-connect (CCC) for leveraging ATM access networks

Support for user-configurable virtual circuits (VC) and virtual paths (VP)

ATM Inverse Address Resolution Protocol (ARP), which enables routers to automatically learn the IP address of the router on the far end of an ATM permanent virtual circuit (PVC)

Unspecified bit rate (UBR) traffic shaping

Fine-grained variable bit rate (VBR) traffic shaping

Outbound PIC queues cells on a per-VC basis

Encapsulations—AAL5 subnetwork attachment point (SNAP)

Cables and connectors

Duplex SC/PC connector (RX and TX)

LEDs One tricolor per port:

Off—Not enabled

Green—Online with no alarms or failures

Amber—Online with alarms for remote failures

Red—Active with a local alarm; router has detected a failure

Alarms, errors, and events

Alarm Indication Signal (AIS-L, AIS-P)

Bit Error Rate Signal Degrade (BERR-SD), Bit Error Rate Signal Fail (BERR-SF)

Bit Interleaved Parity Errors B1, B2, B3 (CV-S, CV-L, CV-P)

Errored Seconds (ES-S, ES-L, ES-P), Far-end Bit Errors REI-L, REI-P (CV-LFE, CV-PFE), Far-end Errored Seconds (ES-LFE, ES-PFE), Far-end Severely Errored Seconds (SES-LFE, SES-PFE), Far-end Unavailable Seconds (UAS-LFE, UAS-PFE)

Loss of Cell Delineation (LoC), Loss of Frame (LoF), Loss of Pointer (LoP-P), Loss of Signal (LoS)

Payload Mismatch (PLM-P), Payload Unequipped (UNEQ-P)

Remote Defect Indication (RDI-L, RDI-P)

Severely Errored Framing (SEF), Severely Errored Framing Seconds (SEFS-S), Severely Errored Seconds (SES-S, SES-L, SES-P), Unavailable Seconds (UAS-L, UAS-P)

Table 2: Optical Interface Support for ATM OC3 PICs

PIC Type Single-mode Intermediate Reach Multimode

Optical interface Single-mode, intermediate reach (Bellcore GR-253 compliant) with SC/PC duplex connector (maximum distance 9.3 miles/15 km) Multimode with SC/PC duplex connector (maximum distance 1.2 miles/2 km), ATM Forum af-phy-0046

Wavelength 1260 through 1360 nm 1270 through 1380 nm

Average launch power –15 through –8 dBm –20 through –14 dBm

Receiver saturation –8 dBm –14 dBm

Receiver sensitivity –28 dBm –30 dBm

PIC Type	Single-mode Intermediate Reach	Multimode
Optical interface	Single-mode, intermediate reach (Bellcore GR-253 compliant) with SC/PC duplex connector (maximum distance 9.3 miles/15 km)	Multimode with SC/PC duplex connector (maximum distance 1.2 miles/2 km), ATM Forum af-phy-0046
Wavelength	1260 through 1360 nm	1270 through 1380 nm
Average launch power	–15 through –8 dBm	–20 through –14 dBm
Receiver saturation	–8 dBm	–14 dBm
Receiver sensitivity	–28 dBm	–30 dBm

[Contents] [Prev] [Next] [Report an Error]

Description	Two OC3 ports Power requirements: 0.49 A/48 V @ 23.7 W Conforms to ANSI T1.105-1991 and T1E1.2/93-020R1 ATM and SONET/SDH standards compliant Alarm and event counting and detection Compatible with well-known ATM switches ATM switch ID, which displays the switch IP address and local interface name of the adjacent Fore ATM switches Optical interface support—see Table 2
Hardware features	Dual 3010 SAR for segmentation and reassembly into 53-byte ATM cells High-performance parsing of SONET/SDH frames OAM fault management processes Alarm Indication Signal (AIS) and Remote Defect Indicator (RDI) cells ASIC-based packet segmentation and reassembly (SAR) management and output port queuing 16-MB SDRAM memory for ATM SAR Packet buffering, Layer 2 parsing
Software features	Multiprotocol Label Switching (MPLS) circuit cross-connect (CCC) for leveraging ATM access networks Support for user-configurable virtual circuits (VC) and virtual paths (VP) ATM Inverse Address Resolution Protocol (ARP), which enables routers to automatically learn the IP address of the router on the far end of an ATM permanent virtual circuit (PVC) Unspecified bit rate (UBR) traffic shaping Fine-grained variable bit rate (VBR) traffic shaping Outbound PIC queues cells on a per-VC basis Encapsulations—AAL5 subnetwork attachment point (SNAP)
Cables and connectors	Duplex SC/PC connector (RX and TX)
LEDs	One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local alarm; router has detected a failure
Alarms, errors, and events	Alarm Indication Signal (AIS-L, AIS-P) Bit Error Rate Signal Degrade (BERR-SD), Bit Error Rate Signal Fail (BERR-SF) Bit Interleaved Parity Errors B1, B2, B3 (CV-S, CV-L, CV-P) Errored Seconds (ES-S, ES-L, ES-P), Far-end Bit Errors REI-L, REI-P (CV-LFE, CV-PFE), Far-end Errored Seconds (ES-LFE, ES-PFE), Far-end Severely Errored Seconds (SES-LFE, SES-PFE), Far-end Unavailable Seconds (UAS-LFE, UAS-PFE) Loss of Cell Delineation (LoC), Loss of Frame (LoF), Loss of Pointer (LoP-P), Loss of Signal (LoS) Payload Mismatch (PLM-P), Payload Unequipped (UNEQ-P) Remote Defect Indication (RDI-L, RDI-P) Severely Errored Framing (SEF), Severely Errored Framing Seconds (SEFS-S), Severely Errored Seconds (SES-S, SES-L, SES-P), Unavailable Seconds (UAS-L, UAS-P)