[Contents] [Prev] [Next] [Report an Error]

Adaptive Services II PIC

Image g002114.gif

Software release

JUNOS 6.4 and later

Description

Supports Network Address Translation (NAT), stateful firewall, intrusion detection services (IDS), IPSec, J-Flow accounting, tunnel services, and voice services.
Note: Individual licenses must be purchased for these features except tunnel services, which is included with the PIC.

Note: J-Flow and voice services are not supported on the Adaptive Services II PIC when it is installed in T-series or M320 routing platforms.

Power requirement: 0.4 A/48 V @ 19 W

Note: On the M5, M10, M20, M40, and M160 routers, this PIC requires an Enhanced FPC. See the hardware guide for your router for more information.

Hardware features

Support for up to 250 service sets

Active monitoring on up to 1 million flows

Support for MTUs up to 9192 bytes for Gigabit Ethernet and SONET interfaces

Software features

Stateful firewall with packet inspection

Detects SYN attacks, ICMP and UDP floods, and ping of death attacks

NAT for IP addresses

Port Address Translation (PAT) for port numbers

J-Flow accounting exports cflowd version 5 and version 8 records

Tunnel services:

IP-IP unicast tunneling

GRE unicast tunneling—supports GRE fragmentation

PIM sparse mode unicast tunneling

Virtual tunnel interface for Layer 3 VPNs

IPSec encryption

Voice services:

Compressed Real-Time Protocol (CRTP)

Compressed User Datagram Protocol (CUDP)

Encapsulations:

High-level Data Link Control (HDLC)

Point-to-Point Protocol (PPP)

Note: Extended support for graceful Routing Engine switchover (GRES) has been added for this PIC. To configure GRES, you must be running JUNOS release 7.3 or later.

LEDs Status LED, one tricolor:

Off—PIC is offline and it is safe to remove it from the chassis.

Green—PIC is operating normally.

Amber—PIC is initializing.

Red—PIC has an error or failure and no further harm can be done by removing it from the chassis.

Application LED, one tricolor:

Off—Service is not running.

Green—Service is running under acceptable load.

Amber—Service is overloaded.

[Contents] [Prev] [Next] [Report an Error]

Description	Supports Network Address Translation (NAT), stateful firewall, intrusion detection services (IDS), IPSec, J-Flow accounting, tunnel services, and voice services. Note: Individual licenses must be purchased for these features except tunnel services, which is included with the PIC. Note: J-Flow and voice services are not supported on the Adaptive Services II PIC when it is installed in T-series or M320 routing platforms. Power requirement: 0.4 A/48 V @ 19 W Note: On the M5, M10, M20, M40, and M160 routers, this PIC requires an Enhanced FPC. See the hardware guide for your router for more information.
Hardware features	Support for up to 250 service sets Active monitoring on up to 1 million flows Support for MTUs up to 9192 bytes for Gigabit Ethernet and SONET interfaces
Software features	Stateful firewall with packet inspection Detects SYN attacks, ICMP and UDP floods, and ping of death attacks NAT for IP addresses Port Address Translation (PAT) for port numbers J-Flow accounting exports cflowd version 5 and version 8 records Tunnel services: IP-IP unicast tunneling GRE unicast tunneling—supports GRE fragmentation PIM sparse mode unicast tunneling Virtual tunnel interface for Layer 3 VPNs IPSec encryption Voice services: Compressed Real-Time Protocol (CRTP) Compressed User Datagram Protocol (CUDP) Encapsulations: High-level Data Link Control (HDLC) Point-to-Point Protocol (PPP) Note: Extended support for graceful Routing Engine switchover (GRES) has been added for this PIC. To configure GRES, you must be running JUNOS release 7.3 or later.
LEDs	Status LED, one tricolor: Off—PIC is offline and it is safe to remove it from the chassis. Green—PIC is operating normally. Amber—PIC is initializing. Red—PIC has an error or failure and no further harm can be done by removing it from the chassis. Application LED, one tricolor: Off—Service is not running. Green—Service is running under acceptable load. Amber—Service is overloaded.