List of Figures

Figure 1: Front of Chassis

Figure 2: Rear of Chassis with Component Cover in Place

Figure 3: Rear of Chassis with Component Cover Removed

Figure 4: Midplane

Figure 5: Front of Chassis with Four-PIC FPC Installed in Slot FPC0

Figure 6: FPC1 and FPC2

Figure 7: Packet Forwarding Engine Clock Generator

Figure 8: Switching and Forwarding Module

Figure 9: Routing Engine

Figure 10: Miscellaneous Control Subsystem

Figure 11: Craft Interface

Figure 12: LCD in Idle Mode

Figure 13: LCD in Alarm Mode

Figure 14: Connector Interface Panel

Figure 15: Routing Engine Interface Ports for Host Module 0 

Figure 16: Alarm Relay Contacts and BITS Input Ports

Figure 17: Original Power Supply

Figure 18: Enhanced Power Supply

Figure 19: Circuit Breaker Box

Figure 20: Airflow through the Chassis

Figure 21: Cable Management System

Figure 22: System Architecture

Figure 23: Packet Forwarding Engine Components and Data Flow

Figure 24: Routing Engine Architecture

Figure 25: Control Packet Handling for Routing and Forwarding Table Updates

Figure 26: Typical Center-Mount Rack

Figure 27: Chassis Dimensions and Clearance Requirements

Figure 28: Power and Grounding Cable Lug

Figure 29: Typical Source Cabling to the Router

Figure 30: Power and Grounding Cable Connections

Figure 31: Unpacking the Router

Figure 32: Removing a Power Supply

Figure 33: Removing an SFM

Figure 34: Removing an MCS

Figure 35: Removing a PCG

Figure 36: Removing a Routing Engine

Figure 37: Removing the Rear Upper Impeller Assembly

Figure 38: Removing the Rear Upper Impeller Assembly

Figure 39: Removing the Rear Lower Impeller Assembly

Figure 40: Removing the Fan Tray

Figure 41: Removing an FPC

Figure 42: Removing the Front Impeller Assembly

Figure 43: Attaching the Lifting Handle

Figure 44: Installing the Chassis in a Rack

Figure 45: Reinstalling the Front Impeller Assembly

Figure 46: Reinstalling an FPC

Figure 47: Reinstalling the Fan Tray

Figure 48: Reinstalling the Rear Lower Impeller Assembly

Figure 49: Reinstalling the Rear Upper Impeller Assembly

Figure 50: Reinstalling the Rear Upper Impeller Assembly

Figure 51: Reinstalling a Routing Engine

Figure 52: Reinstalling a PCG

Figure 53: Reinstalling an MCS

Figure 54: Reinstalling an SFM

Figure 55: Reinstalling a Power Supply

Figure 56: Routing Engine Management Ports and Alarm Relay Contacts

Figure 57: Routing Engine Ethernet Cable Connector

Figure 58: Console and Auxiliary Serial Port Connector

Figure 59: Attaching Cable to a PIC

Figure 60: Connecting Power and Grounding Cables

Figure 61: Removing the Air Filter

Figure 62: Removing the Filter from the Air Filter Cover

Figure 63: Installing the Air Filter

Figure 64: Removing the CIP

Figure 65: Installing the CIP

Figure 66: Routing Engine Interface Ports and Alarm Relay Contacts

Figure 67: Ethernet Cable Connector

Figure 68: Serial Port Connector

Figure 69: Removing the Fan Tray

Figure 70: Installing the Fan Tray

Figure 71: Removing the Front Impeller Assembly

Figure 72: Removing the Screws along the Top Front Edge of the Front Impeller Assembly

Figure 73: Removing the Craft Interface

Figure 74: Installing the Front Impeller Assembly

Figure 75: Removing the Rear Lower Impeller Assembly

Figure 76: Installing the Rear Lower Impeller Assembly

Figure 77: Removing the Rear Upper Impeller Assembly

Figure 78: Removing the Rear Upper Impeller Assembly

Figure 79: Installing the Rear Upper Impeller Assembly

Figure 80: Installing the Rear Upper Impeller Assembly

Figure 81: Removing an MCS

Figure 82: Installing an MCS

Figure 83: Removing the PC Card

Figure 84: Insert the PC Card

Figure 85: Removing a Routing Engine

Figure 86: Installing a Routing Engine

Figure 87: Removing an FPC

Figure 88: Installing an FPC

Figure 89: Connecting Fiber-Optic Cable to a PIC

Figure 90: Removing a PCG

Figure 91: Installing a PCG

Figure 92: Removing a PIC

Figure 93: Installing a PIC

Figure 94: Connecting Fiber-Optic Cable to a PIC

Figure 95: Connecting Fiber-Optic Cable to a PIC

Figure 96: Removing an SFM

Figure 97: Installing an SFM

Figure 98: Small Form Factor Pluggable (SFP)

Figure 99: Removing the Circuit Breaker Box

Figure 100: Installing the Circuit Breaker Box

Figure 101: Removing a Power Supply

Figure 102: Rear of Power Supply Showing Midplane Connectors

Figure 103: Installing a Power Supply

Figure 104: Disconnecting Power Cables

Figure 105: Connecting Power and Grounding Cables

Figure 106: Fuse Locations in the Fuse Box

Figure 107: Fuse Locations in the Fuse Box

Figure 108: Placing a Component into an Electrostatic Bag

Figure 109: Serial Number ID Label 

Figure 110: CIP Serial Number ID Label

Figure 111: Craft Interface Serial Number ID Label

Figure 112: DC Power Supply Serial Number ID Label

Figure 113: FPC Serial Number ID Label

Figure 114: MCS Serial Number ID Label

Figure 115: PCG Serial Number ID Label 

Figure 116: PIC Serial Number ID Label

Figure 117: Routing Engine 333 Serial Number ID Label

Figure 118: Routing Engine 600 Serial Number ID Label

Figure 119: SFM Serial Number ID Label 

Figure 120: EIA-530 PIC

Figure 121: Fast Ethernet 48-port PIC

Figure 122: VHDCI to RJ-21 Cable