• Downloads
• Installing an SRX5800 Services Gateway SCB    

• Related Topics
• Preventing Electrostatic Discharge Damage to the SRX5800 Services Gateway
• Powering Off the SRX5800 Services Gateway
• Taking the SRX5800 Services Gateway Host Subsystem Offline
• Operating and Positioning the SRX5800 Services Gateway SCB Ejectors
• Removing an SRX5800 Services Gateway SCB
• Replacing the SRX5800 Services Gateway Routing Engine
• Replacing the Management Ethernet Cable on an SRX5800 Services Gateway

Installing an SRX5800 Services Gateway SCB

To install an SCB (see Figure 1):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
2. Power-off the services gateway.
3. Carefully align the sides of the SCB with the guides inside the chassis.
4. Slide the SCB into the chassis until you feel resistance, carefully ensuring that it is correctly aligned.
5. Grasp both ejector handles and rotate them simultaneously clockwise until the SCB is fully seated.
6. Place the ejector handles in the proper position, vertically and toward the center of the board.
7. Power-on the services gateway. The OK LED on the power supply faceplate should blink, then light steadily.
8. To verify that the SCB is functioning normally, check the LEDs on its faceplate. The green OK/FAIL LED should light steadily a few minutes after the SCB is installed. If the OK/FAIL LED is red, remove and install the SCB again. If the OK/FAIL LED still lights steadily, the SCB is not functioning properly. Contact your customer support representative.

   To check the status of the SCB:

   
   

   user@host> show chassis environment cb

   CB 0 status:
     State                      Online Master
     Temperature                30 degrees C / 86 degrees F
     Power 1
       1.2 V                     1202 mV
       1.5 V                     1511 mV
       1.8 V                     1798 mV
       2.5 V                     2481 mV
       3.3 V                     3306 mV
       5.0 V                     4956 mV
       12.0 V                   12084 mV
       1.25 V                    1250 mV
       3.3 V SM3                 3287 mV
       5.0 V RE                  5046 mV
       12.0 V RE                11910 mV
     Power 2
       11.3 V bias PEM          11292 mV
       4.6 V bias MidPlane       4833 mV
       11.3 V bias FPD          11156 mV
       11.3 V bias POE 0        11253 mV
       11.3 V bias POE 1        11272 mV
     Bus Revision               42
     FPGA Revision              1
   CB 1 status:
     State                      Online
     Temperature                31 degrees C / 87 degrees F
     Power 1
       1.2 V                     1205 mV
       1.5 V                     1508 mV
       1.8 V                     1817 mV
       2.5 V                     2507 mV
       3.3 V                     3306 mV
       5.0 V                     5053 mV
       12.0 V                   12200 mV
       1.25 V                    1256 mV
       3.3 V SM3                 3306 mV
       5.0 V RE                  5091 mV
       12.0 V RE                    0 mV
     Power 2
       11.3 V bias PEM          11214 mV
       4.6 V bias MidPlane       4821 mV
       11.3 V bias FPD          11350 mV
       11.3 V bias POE 0        11350 mV
       11.3 V bias POE 1        11330 mV
     Bus Revision               42
     FPGA Revision              0

Figure 1: Installing an SCB