Technical Documentation

Taking the T640 Host Subsystem Offline

The host subsystem is taken offline and brought online as a unit. Before you replace a T-CB or Routing Engine, you must take the host subsystem offline.

Normally, if two host subsystems are installed in the T640 router, RE0 functions as the master and RE1 functions as the backup. You can remove the backup host subsystem (or either of its components) without interrupting the functioning of the router. If you take the master host subsystem offline, the backup host subsystem becomes the master (the router might reboot, depending on your configuration). If the router has only one host subsystem, taking the host subsystem offline causes the router to shut down.

Table 1 explains the effect of taking the host subsystem offline.

Table 1: Effect of Taking the Host Subsystem Offline

Type of Host SubsystemEffect of Taking the Host Subsystem Offline

Nonredundant host subsystem

The router shuts down.

Backup host subsystem

The functioning of the router is not interrupted. The backup host subsystem is hot-removable and hot-insertable.

Master host subsystem

The backup host subsystem becomes the master. The backup Routing Engine assumes Routing Engine functions. The master host subsystem is hot-pluggable. Removal or failure of the master Routing Engine affects forwarding and routing based on the high availability configuration:

  • Dual Routing Engines without any high availability features enabled—Traffic is interrupted while the Packet Forwarding Engine is reinitialized. All kernel and forwarding processes are restarted. When the switchover to the new master Routing Engine is complete, routing convergence takes place and traffic is resumed.
  • Graceful Routing Engine switchover (GRES) is enabled—Graceful Routing Engine switchover preserves interface and kernel information. Traffic is not interrupted. However, graceful Routing Engine switchover does not preserve the control plane. Neighboring routers detect that the router has restarted and react to the event in a manner prescribed by individual routing protocol specifications. To preserve routing without interruption during a switchover, graceful Routing Engine switchover must be combined with nonstop active routing.
  • Nonstop active routing is enabled (graceful Routing Engine switchover must be configured for nonstop active routing to be enabled)—Nonstop active routing supports Routing Engine switchover without alerting peer nodes that a change has occurred. Nonstop active routing uses the same infrastructure as graceful Routing Engine switchover to preserve interface and kernel information. However, nonstop active routing also preserves routing information and protocol sessions by running the routing protocol process (rpd) on both Routing Engines. In addition, nonstop active routing preserves TCP connections maintained in the kernel.
  • Graceful restart is configured—Graceful restart provides extensions to routing protocols so that neighboring helper routers restore routing information to a restarting router. These extensions signal neighboring routers about the graceful restart and prevent the neighbors from reacting to the router restart and from propagating the change in state to the network during the graceful restart period. Neighbors provide the routing information that enables the restarting router to stop and restart routing protocols without causing network reconvergence. Neighbors are required to support graceful restart. The routing protocol process (rpd) restarts. A graceful restart interval is required. For certain protocols, a significant change in the network can cause graceful restart to stop.

Note: Router performance might change if the backup Routing Engine's configuration differs from the former master's configuration. For the most predictable performance, configure the two Routing Engines identically, except for parameters unique to each Routing Engine.

Note: For information about configuring graceful Routing Engine switchover, graceful restart, and nonstop active routing, see the Junos High Availability Configuration Guide.

Note: The first supported release for graceful Routing Engine switchover and nonstop active routing on the T640 router is Junos OS Release 7.0 and Junos OS Release 8.4, respectively. Graceful restart software requirements depend on the routing protocols configured on the router. For the minimum software requirements for graceful restart, see the Junos High Availability Configuration Guide.

To take a host subsystem offline:

  1. Determine whether the host subsystem is functioning as the master or as the backup, using one of the two following methods:
    • Check the Routing Engine LEDs on the craft interface. If the green MASTER LED is lit, the corresponding host subsystem is functioning as the master.
    • Issue the following CLI command. The master Routing Engine is designated Master in the Current state field:

      user@host> show chassis routing-engine
      Routing Engine status:
  Slot 0: 
  Current state             Master 
  Election priority         Master (default) 
  Temperature            34 degrees C / 93 degrees F
    DRAM               2048 Mbytes
    CPU utilization: 
    User                  0 percent 
    Background            0 percent 
    Kernel                1 percent 
    Interrupt             0 percent 
    Idle                 99 percent 
    Start time              2002-01-22 05:21:31 UTC
    Uptime                  10 days, 16 hours, 4 minutes, 52 seconds
    Load averages:          1 minute   5 minute  15 minute
                                0.00       0.00       0.00
Routing Engine status:
  Slot 1: 
  Current state             Empty
  2. If the host subsystem is functioning as the master, switch it to backup using the CLI command:

    user@host> request chassis routing-engine master switch
  3. To halt the router:

    user@host> request system halt

    (If two Routing Engines are installed, also issue the command on the backup Routing Engine.) Wait until a message appears on the console confirming that the operating system has halted.

    The command shuts down the Routing Engine cleanly, so its state information is preserved. For more information about the command, see the Junos System Basics and Services Command Reference.

    Note: The SIBs might continue forwarding traffic for approximately 5minutes after the request system halt command has been issued.

Related Topics

Published: 2010-08-11

Help
|
My Account
|
Log Out