Replacing an MX960 DPC
Removing an MX960 DPC
A DPC weighs up to 13.1 lb (5.9 kg). Be prepared to accept its full weight.
To remove a DPC (see Figure 1):
- Have ready a replacement DPC or DPC blank panel and an antistatic mat for the DPC. Also have ready rubber safety caps for each DPC you are removing that uses an optical interface.
- Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
- Label the cables connected to each port on the DPC so that you can later reconnect the cables to the correct ports.
- Use one of the following methods to take the DPC
offline:
- Press and hold the corresponding DPC online button on the craft interface. The green OK LED next to the button begins to blink. Hold the button down until the LED goes off.
- Issue the following CLI command:
user@host>request chassis fpc slot slot-number offlineFor more information about the command, see the Junos System Basics and Services Command Reference.
- Disconnect the cables from the DPC.
Warning: Do not look directly into a fiber-optic transceiver or into the ends of fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a transceiver emit laser light that can damage your eyes.
Caution: Do not leave a fiber-optic transceiver uncovered except when inserting or removing cable. The safety cap keeps the port clean and prevents accidental exposure to laser light.
Caution: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc smaller than a few inches in diameter can damage the cable and cause problems that are difficult to diagnose.
- Immediately cover each optical transceiver and the end of each fiber-optic cable with a rubber safety cap.
- Arrange the disconnected cables in the standard or extended cable manager to prevent the cables from developing stress points.
- Simultaneously turn both of the ejector handles counterclockwise to unseat the DPC.
- Grasp the handles, and slide the DPC straight out of the card cage halfway.
- Place one hand around the front of the DPC and
the other hand under it to support it. Slide the DPC completely out
of the chassis, and place it on the antistatic mat or in the electrostatic
bag.
Caution: The weight of the DPC is concentrated in the back end. Be prepared to accept the full weight—up to 13.1 lb (5.9 kg)—as you slide the DPC out of the chassis.
When the DPC is out of the chassis, do not hold it by the ejector handles, bus bars, or edge connectors. They cannot support its weight.
Do not stack DPCs on top of one another after removal. Place each one individually in an electrostatic bag or on its own antistatic mat on a flat, stable surface.
- If you are not reinstalling a DPC into the emptied DPC
slot within a short time, install a blank DPC panel over the slot
to maintain proper airflow in the DPC card cage.
Caution: After removing a DPC from the chassis, wait at least 30 seconds before reinserting it, removing a DPC from a different slot, or inserting a DPC into a different slot.
Figure 1: Removing a DPC
Installing an MX960 DPC
A DPC weighs up to 14.5 lb (6.6 kg). Be prepared to accept its full weight.
To install a DPC (see Figure 2):
- Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
- Place the DPC on an antistatic mat, or remove it from its electrostatic bag.
- Identify the slot on the router where it will be installed.
- Verify that each fiber-optic transceiver is covered with a rubber safety cap. If it does not, cover the transceiver with a safety cap.
- Orient the DPC so that the faceplate faces youvertically.
- Lift the DPC into place, and carefully align the sides of the DPC with the guides inside the card cage.
- Slide the DPC all the way into the card cage until you feel resistance.
- Grasp both ejector handles, and rotate them clockwise simultaneously until the DPC is fully seated.
- Remove the rubber safety cap from each fiber-optic
transceiver and cable.
Warning: Do not look directly into a fiber-optic transceiver or into the ends of fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a transceiver emit laser light that can damage your eyes.
- Insert the cables into the cable connector ports on each DPC (see Figure 3).
- Arrange the cable in the standard or extended cable manager to prevent
it from dislodging or developing stress points. Secure the cable so
that it is not supporting its own weight as it hangs to the floor.
Place excess cable out of the way in a neatly coiled loop. Placing fasteners on the loop helps to maintain its shape.
Caution: Do not let fiber-optic cable hang free from the connector. Do not allow fastened loops of cable to dangle, which stresses the cable at the fastening point.
Caution: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc smaller than a few inches in diameter can damage the cable and cause problems that are difficult to diagnose.
- Use one of the following methods to bring the DPC online:
- Press and hold the corresponding DPC online button on the craft interface until the green OK LED next to the button lights steadily, in about 5 seconds.
- Issue the following CLI command:
user@host>request chassis fpc slot slot-number onlineFor more information about the command, see the Junos System Basics and Services Command Reference.
Caution: After the OK LED turns green, wait at least 30 seconds before removing the DPC again, removing a DPC from a different slot, or inserting a DPC in a different slot.
You can also verify that the DPC is functioning correctly by issuing the show chassis fpc and show chassis fpc pic-status commands.
Figure 2: Installing a DPC
Figure 3: Attaching a Cable to a DPC
