Initially Configuring the M10i Router
The router is shipped with the Junos OS preinstalled and ready to be configured when the router is powered on. There are three copies of the software: one on a CompactFlash card (if installed) in the Routing Engine, one on the hard disk in the Routing Engine, and one on a PC card that can be inserted into the slot in the Routing Engine faceplate.
When the router boots, it first attempts to start the image on the PC card. If a PC card is not inserted into the Routing Engine or the attempt otherwise fails, the router next tries the CompactFlash card (if installed), and finally the hard disk.
You configure the router by issuing Junos OS command-line interface (CLI) commands, either on a console device attached to the CONSOLE port on the Routing Engine, or over a telnet connection to a network connected to the MGMT port on the Routing Engine.
Gather the following information before configuring the router:
- Name the router will use on the network
- Domain name the router will use
- IP address and prefix length information for the Ethernet interface
- IP address of a default router
- IP address of a DNS server
- Password for the root user
This procedure connects one router to the network but does not enable it to forward traffic. For complete information about enabling the router to forward traffic, including examples, see the Junos OS configuration guides.
To configure the software:
- Verify that the router is powered on, as described in Powering On an AC-Powered M10i Router or Powering On a DC-Powered M10i Router.
- Log in as the root user. There is no password.
Amnesiac <ttyd0>
login: root - Start the CLI.root@% cliroot>
- Enter configuration mode.root> configure Entering configuration mode.[edit]root@#
- Add a password to the root administration
user account. Enter a clear-text password. For information about using
an encrypted password, or an SSH public key string (DSA or RSA), see
the Junos System Basics Configuration Guide.[edit]root@# set system root-authentication plain-text-passwordNew password: password Retype new password: password
- Create a management console user account.
[edit]
root# set system login user user-name authentication plain-text-password
New Password: password
Retype new password: password - Set the user account class to super-user.
[edit]
root# set system login user user-name class super-user - Configure
the name of the router. If the name includes spaces, enclose the name
in quotation marks (“ ”).[edit]root@# set system host-name host-name
Note: The DNS server does not use the host name to resolve to the correct IP address. This host name is used to display the name of the routing engine in the CLI. For example, this host name shows on the command line prompt when the user is logged on to the CLI:
user-name@host-name>
- Configure the IP address of the DNS server.
[edit]
root# set system name-server address - Configure the router’s domain name.[edit]root@# set system domain-name domain-name
- Configure the IP address and prefix length
for the router’s Ethernet interface.[edit]root@# set interfaces fxp0 unit 0 family inet address address/prefix-length
- Configure the IP address of a backup
router. The backup router is used while the local router is booting
and if the routing process fails to start. After the routing process
starts, the backup router address is removed from the local routing
and forwarding tables. For more information on the backup router,
see the Junos System Basics Configuration Guide.
[edit]
root# set system backup-router address - (Optional) Configure the static routes
to remote subnets with access to the management port. Access to the
management port is limited to the local subnet. To access the management
port from a remote subnet, you need to add a static route to that
subnet within the routing table. For more information on static routes,
see the Junos System Basics Configuration Guide.
[edit] root# set routing-options static route remote-subnet next-hop destination-IP retain no-readvertise
- Configure the telnet service at the [edit system services] hierarchy level.
[edit]
set system services telnet - Optionally, display the configuration
to verify that it is correct.[edit]root@# showsystem {host-name host-name;domain-name domain-name;backup-router address;root-authentication {authentication-method (password | public-key);}name-server {address;}}interfaces {fxp0 {unit 0 {family inet {address address/prefix-length;}}}}
- Commit
the configuration to activate it on the router.[edit]root@# commit
- Optionally,
configure additional properties by adding the necessary configuration
statements. Then commit the changes to activate them on the router.[edit]root@host# commit
- When you have finished configuring the
router, exit configuration mode.[edit]root@host# exitroot@host>
| Note: To reinstall the Junos OS, you boot the router from the removable media. Do not insert the removable media during normal operations. The router does not operate normally when it is booted from the removable media. |
When the router boots from the storage media (removable media, CompactFlash card, or hard disk) it expands its search in the /config directory of the routing platform for the following files in the following order: juniper.conf (the main configuration file), rescue.conf (the rescue configuration file), and juniper.conf.1 (the first rollback configuration file). When the search finds the first configuration file that can be loaded properly, the file loads and the search ends. If none of the file can be loaded properly, the routing platform does not function properly. If the router boots from an alternate boot device, the Junos OS displays a message indication this when you log in to the router.
