• Supported Platforms
• EX Series

• Related Topics
• Connecting and Configuring an EX Series Switch (CLI Procedure)
• Installing and Connecting an EX2200 Switch
• Installing and Connecting an EX3200 or EX4200 Switch
• Installing and Connecting an EX4500 Switch
• Installing and Connecting an EX8208 Switch
• Installing and Connecting an EX8216 Switch

Connecting and Configuring an EX Series Switch (J-Web Procedure)

There are two ways to connect and configure an EX Series switch: one method is through the console using the CLI and the other is using the J-Web interface. This topic describes the J-Web procedure.

Note: Before you begin the configuration, enable a DHCP client on the management PC you will connect to the switch so that the switch can obtain an IP address dynamically.

Note: Read the following steps before you begin the configuration. You must complete the initial configuration using EZSetup within 10 minutes. The switch exits EZSetup after 10 minutes and reverts to the factory default configuration, and the PC loses connectivity to the switch. EX2200 switch—The LEDs on the network ports on the front panel blink when the switch is in the initial setup mode. EX3200, EX4200, EX4500, or EX8200 switch—The LCD displays a count-down timer when the switch is in initial setup mode.

To connect and configure the switch using the J-Web interface:

1. Transition the switch into initial setup mode:
   • EX2200 switch—Press the mode button located on the lower right corner of the front panel for 10 seconds.
   • EX3200, EX4200, EX4500, or EX8200 switch—Use the Menu and Enter buttons located to the right of the LCD panel (see Figure 1):

     Figure 1: LCD Panel in an EX3200, EX4200, EX4500, or EX8200 Switch

     

     1. Press the Menu button until you see MAINTENANCE MENU. Then press the Enter button.
     2. Press Menu until you see ENTER EZSetup. Then press Enter.

        If EZSetup does not appear as an option in the menu, select Factory Default to return the switch to the factory default configuration. EZSetup is displayed in the menu only when the switch is set to the factory default configuration.

     3. Press Enter to confirm setup and continue with EZSetup.
2. Connect the Ethernet cable from the Ethernet port on the PC to the switch.
   • EX2200, EX3200, or EX4200 switch—Connect the cable to port 0 (ge-0/0/0) on the front panel of the switch.
   • EX4500 switch—Connect the cable to the port labeled MGMT on the front panel of the switch.
   • EX8200 switch—Connect the cable to the port labeled MGMT on the Switch Fabric and Routing Engine (SRE) module in slot SRE0 in an EX8208 switch or on the Routing Engine (RE) module in slot RE0 in an EX8216 switch.

   These ports are configured as the DHCP server with the default IP address, 192.168.1.1. The switch can assign an IP address to the management PC in the IP address range 192.168.1.2 through 192.168.1.253.

3. From the PC, open a Web browser, type http://192.168.1.1 in the address field, and press Enter.
4. On the J-Web login page, type root as the username, leave the password field blank, and click Login.
5. On the Introduction page, click Next.
6. On the Basic Settings page, modify the hostname, the root password, and date and time settings:
   • Enter the hostname. This is optional.
   • Enter a password and reenter the password.
   • Specify the time zone.
   • Synchronize the date and time settings of the switch with the management PC or set them manually by selecting the appropriate option button. This is optional.

   Click Next.

7. Use the Management Options page to select the management scenario:

   Note: On EX4500 and EX8200 switches, only the out-of-band management option is available.

   • In-band Management—Use VLAN 'default' for management.

     Select this option to configure all data interfaces as members of the default VLAN. Click Next. Specify the management IP address and the default gateway for the default VLAN.

   • In-band Management—Create new VLAN for management.

     Select this option to create a management VLAN. Click Next. Specify the VLAN name, VLAN ID, member interfaces, management IP address, and default gateway for the new VLAN.

   • Out-of-band Management—Configure management port.

     Select this option to configure only the management interface. Click Next. Specify the IP address and default gateway for the management interface.

8. Click Next.
9. On the Manage Access page, you may select options to enable Telnet, SSH, and SNMP services. For SNMP, you can configure the read community, location, and contact.
10. Click Next. The Summary screen displays the configured settings.
11. Click Finish.

The configuration is committed as the active switch configuration. You can now log in with the CLI or the J-Web interface to continue configuring the switch.

If you use the J-Web interface to continue configuring the switch, the Web session is redirected to the new management IP address. If the connection cannot be made, the J-Web interface displays instructions for starting a J-Web session.

Note: After the configuration is committed, the connectivity between the PC and the switch might be lost. To renew the connection, release and renew the IP address by executing the appropriate commands on the management PC or by removing and reinserting the Ethernet cable.