Software release

• Junos OS Release 9.3 and later (Type 1)

Description

• Two OC3 or STM1 ports
• SONET or SDH is configurable on a per-port granularity
• Channelization: OC3, DS3, DS1, DS0, E3, E1
• SONET channelization:
  • 2 OC3 channels
  • 6 DS3 channels
  • 168 DS1 channels
  • 1011 DS0 channels
• SDH channelization:
  • 2 STM1 channels (non-concatenated)
  • 6 E3 channels
  • 126 E1 channels
  • 6 DS3 channels (Junos OS Release 10.1 and later)
  • 168 DS1 channels (Junos OS Release 10.1 and later)
  • 1011 DS0 channels
• Power requirement: 0.56 A @ 48 V (27.1 W)

Hardware features

• Ports are numbered 0 and 1 from left to right

Software features

• Dynamic, arbitrary channel configuration
• Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED)
• Enhanced fine-grained queuing per logical interface. See the Junos Class of Service Configuration Guide for more information about class of service features.
• Subrate and scrambling:
  • Digital Link/Quick Eagle
  • Kentrox
  • Larscom
  • ADTRAN
  • Verilink
• Packet buffering, Layer 2 parsing
• M13/C-bit parity encoding
• DS3 far-end alarm and control (FEAC) channel support
• Local line, remote line, and remote payload loopback testing
• Simple Network Management Protocol (SNMP): OC3 MIB, DS3 MIB, T1 MIB
• Full bit error rate test (BERT)

• Encapsulations:

  • Circuit cross-connect (CCC)
  • Translational cross-connect (TCC)
  • Extended Frame Relay for CCC and TCC
  • Flexible Frame Relay
  • Frame Relay
  • Frame Relay for CCC
  • Frame Relay for TCC
  • Frame Relay port CCC
  • High-Level Data Link Control (HDLC)
  • HDLC framing for CCC
  • HDLC framing for TCC
  • MPLS CCC
  • MPLS TCC
  • Multilink Frame Relay (MLFR) UNI NNI (MFR FRF.16)
  • Point-to-Point Protocol (PPP)
  • PPP for CCC
  • PPP for TCC

• Encapsulations available only for DS1:

  • Multilink Frame Relay end-to-end (MLFR FRF.15)
  • Multilink PPP (MLPPP)
  • PPP over Frame Relay

Cables and connectors

• Duplex LC/PC connector (Rx and Tx)
• SONET/SDH OC3/STM1 SFPs:
  • Multimode (model number: SFP-OC3-SR)
  • Intermediate reach (IR-1) (model number: SFP-OC3-IR)
  • Long reach (LR-1) (model number: SFP-OC3-LR)

  Optical interface specifications—see SONET/SDH OC3/STM1 Optical Interface Specifications

LEDs

One tricolor Status LED per port:

• Off—Not enabled.
• Green—Online with no alarms or failures.
• Yellow—Online with alarms for remote failures.
• Red—Active with a local alarm; router has detected a failure.

Alarms, errors, and events

• SONET alarms:

  • Alarm indication signal—line (AIS-L)
  • Alarm indication signal—path (AIS-P)
  • Bit error rate—signal degrade (BERR-SD)
  • Bit error rate—signal fail (BERR-SF)
  • Loss of frame (LOF)
  • Loss of light (LOL)
  • Loss of pointer (LOP)
  • Loss of signal (LOS)
  • Payload label mismatch (PLM-P)
  • Remote defect indication—line (RDI-L)
  • Remote defect indication—path (RDI-P)
  • Remote error indication (REI)
  • Payload unequipped (unequipped STS at path level) (UNEQ-P)
  • Virtual container—alarm indication signal (VAIS)
  • Virtual container—loss of pointer (VLOP)
  • Virtual container—mismatch (VMIS)
  • Virtual container—remote defect indication (VRD1)
  • Virtual container—unequipped (VUNEQ)

• SDH alarms:

  • Administrative unit alarm indication signal (AU-AIS)
  • Bit error rate signal degrade (BERR-SD)
  • Bit error rate signal fail (BERR-SF)
  • Bit interleaved parity (BIP) error B1, B2, B3
  • Higher order path—alarm indication signal (HP-AIS)
  • Higher order path—far-end receiver error (HP-FERF)
  • Higher order path—payload label mismatch (HP-PLM)
  • Higher order path—loss of pointer (HP-LOP)
  • Higher order path—remote defect indication (HP-RDI)
  • Higher order path—unequipped (HP-UNEQ)
  • Loss of frame (LOF)
  • Loss of light (LOL)
  • Loss of signal (LOS)
  • Multiplex section—alarm indication signal (MS-AIS)
  • Multiplex section—far-end receive error (MS-FERF)
  • Multiplex section—remote defect indication (MS-RDI)
  • Multiplex section—remote error indication (MS-REI)
  • Phase lock loop (PLL)
  • Remote error indication (REI)
  • Severely errored frame (SEF)
  • Tributary unit—alarm indication signal (TU-AIS)
  • Tributary unit—loss of pointer (TU-LOP)
  • Tributary unit—mismatch (TU-MIS)
  • Tributary unit—remote defect indication (TU-RD1)
  • Tributary unit—unequipped (TU-UNEQ)

• DS1 alarms:

  • Alarm indication signal (AIS)
  • Loss of frame (LOF)
  • Remote alarm indication signal (RAIS)

• DS1 error detection:

  • Bursty errored seconds (BES)
  • CRC errors
  • Errored seconds (ES)
  • Line errored seconds (LES)
  • Loss of framing seconds (LOFS)
  • Loss of signal seconds (LOS)
  • Severely errored seconds (SES)
  • Severely errored framing seconds (SEFS)
  • Unavailable seconds (UAS)

• DS3 alarms:

  • Alarm indication signal (AIS)
  • Loss of frame (LOF)
  • Loss of signal (LOS)
  • Phase lock loop (PLL)

• DS3 error detection:

  • C-bit code violations (CCV)
  • C-bit errored seconds (CES)
  • C-bit severely errored framing seconds (CEFS)
  • CRC errors
  • Excessive zeros (EXZ)
  • Far-end block error (FEBE)
  • Far-end receive failure (FERF)
  • Line errored seconds (LES)
  • Parity bit (P-bit) code violations (PCV)
  • Parity bit (P-bit) errored seconds (PES)
  • Parity bit (P-bit) severely errored framing seconds (PSES)
  • Severely errored framing seconds (SEFS)
  • Unavailable seconds (UAS)