Software release

• Junos OS Release 8.0R2 and later (Type 2)

Note: This PIC is not supported in Junos OS Release 8.1R1.

Description

• One OC48 port
• Power requirement: 0.41 A @ 48 V ( 20 W)
• Fine-grained queuing per logical interface.
• Conforms to ANSI T1.105-1991 and T1E1.2/93-020R1
• Complies with ATM and SONET/SDH standards
• Alarm and event counting and detection
• Compatible with well-known ATM switches
• ATM switch ID, which displays the switch IP address and local interface name of the adjacent Fore ATM switches

Hardware features

• ATM2 IQ 1-port OC48 PICs have one 3010 SAR for segmentation and reassembly into 53-byte ATM cells.
• High-performance parsing of SONET/SDH frames
• ASIC-based packet segmentation and reassembly (SAR) management and output port queuing
• 64-MB SDRAM memory for ATM SAR
• Packet buffering, Layer 2 parsing

Software features

• Multiprotocol Label Switching (MPLS) circuit cross-connect for leveraging ATM access networks
• User-configurable virtual circuit (VC) and virtual path (VP) support
• Support for idle cell or unassigned cell transmission
• OAM fault management processes alarm indication signal (AIS), remote defect indicator (RDI), and loop cells
• Point-to-point and point-to-multipoint mode Layer 2 counters per VC and per VP
• Local and remote loopback
• ATM Inverse ARP, which enables routers to automatically learn the IP address of the router on the far end of an ATM PVC
• Simple Network Management Protocol (SNMP):
  • Management Information Base (MIB) 2 (RFC 1213)
  • ATM MIB (RFC 1695)
  • SONET MIB
• Unspecified bit rate (UBR), non-real-time variable bit rate (VBR), and constant bit rate (CBR) traffic shaping
• Per-VC or per-VP traffic shaping
• Support for F4 OAM cells
• Support for 16-bit VCI range

Cables and connectors

• Duplex LC/PC connector (RX and TX)
• SONET/SDH OC48/STM16 SFPs:
  • Intermediate reach (IR-1) (model number: SFP-1OC48–IR)

  Optical interface specifications—see SONET/SDH OC48/STM16 Optical Interface Specifications

LEDs

One tricolor per port:

• Off—Not enabled
• Green—Online with no alarms or failures
• Yellow—Online with alarms for remote failures
• Red—Active with a local alarm; router has detected a failure

Alarms, errors, and events

• Alarm indication signal (AIS-L, AIS-P)
• Bit error rate signal degrade (BERR-SD), bit error rate signal fail (BERR-SF)
• Bit interleaved parity errors B1, B2, B3
• Errored seconds (ES-S, ES-L, ES-P), far-end bit errors REI-L, REI-P (CV-LFE, CV-PFE), far-end errored seconds (ES-LFE, ES-PFE), far-end severely errored seconds (SES-LFE, SES-PFE), far-end unavailable seconds (UAS-LFE, UAS-PFE)
• Loss of cell delineation (LOC), loss of frame (LOF), loss of pointer (LOP-P), loss of signal (LOS)
• Payload mismatch (PLM-P), payload unequipped (UNEQ-P)
• Remote defect indication (RDI-L, RDI-P)
• Severely errored framing (SEF), severely errored framing seconds (SEFS-S), severely errored seconds (SES-S, SES-L, SES-P), unavailable seconds (UAS-L, UAS-P)