T1600 Flexible PIC Concentrator (FPC) Description
FPCs are hot-removable and hot-insertable.
T1600 FPC Function
FPCs house the PICs that connect the T1600 Core Router to network media. The main function of an FPC is to connect the PICs installed in it to the other T1600 router components. The Packet Forwarding Engine receives incoming packets from the PICs installed on the FPC and forwards them through the switch planes to the appropriate destination port. In a maximum configuration with eight Type 4 FPCs installed, the Packet Forwarding Engines can forward up to 1600 million packets per second (Mpps) for all packet sizes. The T1600 Core Router provides up to 800 gigabits per second (Gbps), full duplex switching (1600 Gbps of any-to-any, nonblocking, half-duplex switching).
When you install an FPC into a functioning router, the Routing Engine downloads the FPC software, the FPC runs its diagnostics, and the PICs housed on the FPC, are enabled. Forwarding on other FPCs continues uninterrupted during this process.
T1600 FPC Slots
Up to eight FPCs install vertically in the front of the router. The FPC slots are numbered FPC0 through FPC7, left to right. If a slot is not occupied by an FPC, an FPC blank panel must be installed to shield the empty slot and to allow cooling air to circulate properly through the router.
T1600 FPC Components
Each FPC consists of the following components:
- FPC card carrier.
- One or two Packet Forwarding Engines, consisting of Layer
2/Layer 3 Packet Processing ASICs, Switch Interface ASICs, T-series
Internet Processor ASICs, and a Memory Mezzanine Board (MMB) which
includes the Queuing and Memory Interface ASICs.
- Each Type 1 FPC has one Packet Forwarding Engine
- Each Type 2 FPC has one Packet Forwarding Engine
- Each Type 3 FPC has two Packet Forwarding Engines
- Each T640-FPC4-ES has one Packet Forwarding Engine
- Each T640-FPC4-1P-ES has one Packet Forwarding Engine
- Each T1600-FPC4-ES has two Packet Forwarding Engines
- Processor Mezzanine Board (PMB), which includes a 300-MHz CPU, system controller, 256 MB of SDRAM, and two Fast Ethernet interfaces.
- Two LEDs, located on the craft interface above the FPC, that display the status of the FPC.
- FPC online/offline button, located on the craft interface above the FPC.
T1600 FPC Terminology
Regardless of whether you are holding an FPC vertically or horizontally, this document uses the same terms for all four edges of the FPC (see Figure 1):
- Faceplate—Edge of the FPC that has slots into which you insert the PICs
- Connector edge—Edge opposite the faceplate; this edge has the connectors that attach to the midplane
- Top edge—Edge at the top of the FPC when it is vertical
- Bottom edge—Edge at the bottom of the FPC when it is vertical
Figure 1: FPC Edges
Identifying the T1600 FPCs
Check the label on the faceplate to identify the FPC. For FPCs without a label on the faceplate, check the location of a PIC's offline button and how the PIC is secured to the FPC. See Table 1.
Table 1: Identifying the FPCs Supported by the T1600 Router
FPC | Label on the FPC Faceplate | Location of PIC Offline Button | Method of Securing the PIC to the FPC |
|---|---|---|---|
Enhanced FPC1 | E FPC1 Is this correct? I’m guessing. | Slightly beneath the faceplate of the PIC | Two captive screws |
Enhanced II FPC1 | E-II FPC1 | Slightly beneath the faceplate of the PIC | Two captive screws |
Enhanced Scaling FPC1 | T640-FPC1-ES | Slightly beneath the faceplate of the PIC | Two captive screws |
FPC2 | None | Inside an opening directly on the faceplate of each PIC | Two captive screws |
Enhanced FPC2 | E FPC2 | Inside an opening directly on the faceplate of each PIC | Two captive screws |
Enhanced II FPC2 | E-II FPC2 | Inside an opening directly on the faceplate of each PIC | Two captive screws |
Enhanced Scaling FPC2 | T640-FPC2-ES | Inside an opening directly on the faceplate of each PIC | Two captive screws |
FPC3 | None | Inside an opening directly on the faceplate of each PIC | Plastic ejector handle at the top of the PIC faceplate; captive screw at the bottom of the PIC faceplate |
Enhanced FPC3 | E FPC3 | Inside an opening directly on the faceplate of each PIC | Plastic ejector handle at the top of the PIC faceplate; captive screw at the bottom of the PIC faceplate |
Enhanced II FPC3 | E-II FPC3 | Inside an opening directly on the faceplate of each PIC | Plastic ejector handle at the top of the PIC faceplate; captive screw at the bottom of the PIC faceplate |
Enhanced Scaling FPC3 | T640-FPC3-ES | Inside an opening directly on the faceplate of each PIC | Two plastic ejector handles at the top and bottom of the PIC faceplate |
T640 Enhanced Scaling FPC4 | FPC4 | Inside an opening directly on the faceplate of each PIC | Two plastic ejector handles at the top and bottom of the PIC faceplate |
T640 Enhanced Scaling FPC4-1P | T640-FPC4–1P-ES | Inside an opening directly on the faceplate of each PIC | Two plastic ejector handles at the top and bottom of the PIC faceplate |
T1600 Enhanced Scaling FPC4 | T1600-FPC4 | Inside an opening directly on the faceplate of each PIC | Two plastic ejector handles at the top and bottom of the PIC faceplate |
The T1600 router supports the Enhanced Scaling FPC1, as shown in Figure 2.
Figure 2: Enhanced Scaling FPC1 Supported by the T1600 Router
The T1600 router supports the standard FPC2 and FPC3, as shown in Figure 3.
Figure 3: Standard FPC2 and FPC3 Supported by the T1600 Router
The T1600 router supports the Enhanced II FPC1, FPC2, and FPC3, as shown inFigure 4.
Figure 4: Enhanced II FPC1, FPC2, and FPC3 Supported by the T1600 Router
The T1600 router supports the Enhanced Scaling FPC2, as shown in Figure 5.
Figure 5: Enhanced Scaling FPC2 Supported by the T1600 Router
The T1600 router supports the Enhanced Scaling FPC3, as shown in Figure 6.
Figure 6: Enhanced Scaling FPC3 Supported by the T1600 Router
The T1600 router supports the T640 Enhanced Scaling FPC4, as shown in Figure 7.
Figure 7: T640 Enhanced Scaling FPC4 Supported by the T1600 Router
The T1600 router supports the T640 Enhanced Scaling FPC4-1P, as shown in Figure 8.
Figure 8: T640 Enhanced Scaling FPC4-1P Supported by the T1600 Router
The T1600 router supports the T1600 Enhanced Scaling FPC4, as shown in Figure 9.
Figure 9: T1600 Enhanced Scaling FPC4 Supported by the T1600 Router
