IP Multicast Operational Mode Commands
Table 1 summarizes the command-line interface (CLI) commands you can use to monitor and troubleshoot IP multicast. In the table, the commands are listed in alphabetical order.
Table 1: IP Multicast Operational Mode Commands
Task | Command |
|---|---|
Clear Automatic Multicast Tunneling (AMT) protocol statistics. | |
Clear Automatic Multicast Tunneling (AMT) protocol state. | |
Clear Internet Group Management Protocol (IGMP) group members. | |
Clear IGMP snooping membership information. | |
Clear IGMP snooping statistics. | |
Clear IGMP statistics. | |
Clear Multicast Listener Discovery (MLD) group members. | |
Clear MLD statistics. | |
Clear Multicast Source Discovery Protocol (MSDP) source active cache. | |
Clear MSDP statistics. | |
Clear multicast bandwidth admissions. | |
Clear multicast scope. | |
Clear multicast sessions. | |
Clear multicast snooping statistics. | |
Clear multicast statistics. | |
Clear Pragmatic General Multicast (PGM) negative acknowledgments (NAKs). | |
Clear PGM source-path messages. | |
Clear PGM statistics. | |
Clear the Protocol Independent Multicast (PIM) join and prune states. | |
Redistribute PIM joins among available links. | |
Clear PIM register message counters. | |
Clear PIM statistics. | |
Rebalance multicast tunnel (MT) interfaces. | |
Display Automatic Multicast Tunneling (AMT) protocol tunnel statistics. | |
Display summary information about the Automatic Multicast Tunneling (AMT) protocol. | |
Display information about the Automatic Multicast Tunneling (AMT) dynamic tunnels. | |
Display the status of interfaces on which Distance Vector Multicast Routing Protocol (DVMRP) is configured. | |
Display DVMRP neighbors. | |
Display DVMRP prefixes. | |
Display DVMRP prunes. | |
Display members of IGMP groups. | |
Display members of IGMP groups by interface. | |
Display IGMP snooping interface information. | |
Display IGMP snooping membership information. | |
Display IGMP snooping statistics. | |
Display IGMP statistics. | |
Display members of MLD groups. | |
Display members of MLD groups by interface. | |
Display MLD statistics. | |
Display MSDP peers. | |
Display multicast sources learned from MSDP. | |
Display the MSDP source-active cache. | |
Display MSDP statistics. | |
Display configuration information about IP multicast flow maps. | |
Display multicast interface bandwidth information. | |
Display multicast network configuration. | |
Display entries in the multicast next-hop table. | |
Display configuration information about PIM-to-IGMP message translation, also known as PIM-to-IGMP proxy. | |
Display configuration information about PIM-to-MLD message translation, also known as PIM-to-MLD proxy. | |
Display entries in the multicast forwarding cache. | |
Display multicast reverse-path-forwarding calculations. | |
Display administratively scoped addresses. | |
Display announced multicast sessions. | |
Display multicast snooping route. | |
Display multicast snooping statistics. | |
Display multicast statistics. | |
Display most active multicast groups. | |
Display sent or received NAKs. | |
Display PGM source-path messages. | |
Display PGM statistics. | |
Display bootstrap routers. | |
Display the status of interfaces on which PIM is configured. | |
Display PIM (*,*,RP) join and prune states. | |
Display PIM data-driven multicast distribution trees (MDTs). | |
Display PIM neighbors. | |
Display rendezvous points. | |
Display PIM source RPF state. | |
Display PIM statistics. | |
Display Session Announcement Protocol (SAP) addresses. | |
Test MSDP peers. |
 | Note: For information about the mtrace commands used to monitor IP multicast traffic in real time, see the Junos System Basics and Services Command Reference. For information about how to configure IP multicast, see the Junos Multicast Protocols Configuration Guide. |
