Interface

Name of an adaptive services interface.

All levels

Tunnel group

Name of a tunnel group.

All levels

Tunnel local ID

Identifier of the local endpoint of the tunnel, as assigned by the L2TP network server (LNS).

All levels

Session local ID

Identifier of the local endpoint of the L2TP session, as assigned by the LNS.

All levels

Session remote ID

Identifier of the remote endpoint of the L2TP session, as assigned by the L2TP access concentrator (LAC).

All levels

State

State of the L2TP session:

• Established—The session is operating.
• closed—The session is being closed.
• destroyed—The session is being destroyed.
• clean-up—The session is being cleaned up.
• lns-ic-accept-new—A new session is being accepted.
• lns-ic-idle—The session has been created and is idle.
• lns-ic-reject-new—The new session is being rejected.
• lns-ic-wait-connect—The session is waiting for the peer's incoming call connected (ICCN) message.

All levels

Bundle ID

Bundle identifier. Indicates the session is part of a multilink bundle. Sessions that have a blank Bundle field are not participating in the Multilink Protocol. Sessions in a multilink bundle might belong to different L2TP tunnels. For L2TP output organized by bundle ID, issue the show services l2tp multilink extensive command.

All levels

Mode

Mode of the interface representing the session: shared or exclusive.

extensive

Local IP

IP address of local endpoint of the Point-to-Point Protocol (PPP) session.

extensive

Remote IP

IP address of remote endpoint of the PPP session.

extensive

Username

Name of the user logged in to the session.

All levels

Assigned IP address

IP address assigned to remote client.

extensive

Local name

Name of the LNS instance in which the session was created.

extensive

Remote name

Name of the LAC from which the session was created.

extensive

Local MRU

Maximum receive unit (MRU) setting of the local device, in bytes.

extensive

Remote MRU

MRU setting of the remote device, in bytes.

extensive

Tx speed

Transmit speed of the physical PPP link, in bps.

extensive

Rx speed

Receive speed of the physical PPP link, in bps.

extensive

Bearer type

Type of bearer enabled:

• 0—Might indicate that the call was not received over a physical link (for example, when the LAC and PPP are located in the same subsystem).
• 1—Digital access requested
• 2—Analog access requested
• 4—Asynchronous Transfer Mode (ATM) bearer support

extensive

Framing type

Type of framing enabled:

• 1—Synchronous framing
• 2—Asynchronous framing

extensive

LCP renegotiation

Whether Link Control Protocol (LCP) renegotiation is configured: On or Off.

extensive

Authentication

Type of authentication algorithm used: Challenge Handshake Authentication Protocol (CHAP) or Password Authentication Protocol (PAP).

extensive

Interface ID

Identifier used to look up the logical interface for this session.

extensive

Interface unit

Logical interface for this session.

All levels

Call serial number

Unique serial number assigned to the call.

extensive

Policer bandwidth

Maximum policer bandwidth configured for this session.

extensive

Policer burst size

Maximum policer burst size configured for this session.

extensive

Firewall filter

Configured firewall filter name.

extensive

Session encapsulation overhead

Overhead allowance configured for this session, in bytes.

extensive

Session cell overhead

Cell overhead activation (On or Off).

extensive

Create time

Date and time when the call was created.

extensive

Up time

Length of time elapsed since the call became active, in hours, minutes, and seconds.

extensive

Idle time

Length of time elapsed since the call became idle, in hours, minutes, and seconds.

extensive

Statistics since

Date and time when collection of the following statistics began:

• Control Tx—Amount of control information transmitted, in packets and bytes.
• Control Rx—Amount of control information received, in packets and bytes.
• Data Tx—Amount of data transmitted, in packets and bytes.
• Data Rx—Amount of data received, in packets and bytes.
• Errors Tx—Number of errors transmitted, in packets.
• Errors Rx—Number of errors received, in packets.

extensive