GMPLS Overview

Generalized Multiprotocol Label Switching (GMPLS) is the next-generation implementation of Multiprotocol Label Switching (MPLS). GMPLS extends the functionality of MPLS to include a wider range of label-switched path (LSP) options for a variety of network devices.

You should have a general understanding of MPLS, label switching concepts, and GMPLS Phase 1. For more information about MPLS, see the Junos MPLS Applications Configuration Guide. For more information about GMPLS Phase 1, see the Junos 5.5 Feature Guide at: http://www.juniper.net/techpubs/
software/junos/junos55/feature-guide55/feature-guide-55.pdf.

Traditional MPLS is designed to carry Layer 3 IP traffic by establishing IP-based paths and associating these paths with arbitrarily assigned labels. These labels can either be configured explicitly by a network administrator or dynamically assigned by a protocol such as the Label Distribution Protocol (LDP) or Resource Reservation Protocol (RSVP).

In contrast, GMPLS can carry various types of Layer 1 through Layer 3 traffic. GMPLS labels and LSPs can be processed at four levels, as depicted in Figure 1. The levels are Fiber-Switched Capable (FSC), Lambda-Switched Capable (LSC), Time-Division Multiplexing Capable (TDM), and Packet-Switched Capable (PSC).

LSPs must start and end on links with the same switching capability. To send an LSP, a label-switched device must communicate with another device at the same layer of the Open System Interconnection (OSI) model. Thus, routers can set up PSC LSPs with other routers at Layer 3, and SONET/SDH add/drop multiplexers (ADMs) can establish TDM LSPs with other ADMs at Layer 1. As seen in Figure 1, a router PSC LSP can be carried over a TDM LSP, a TDM LSP can be carried over a wavelength LSC LSP, and so on.

This extension of the MPLS protocol expands the number of devices that can participate in label switching. Lower layer devices, such as optical cross-connects (OXCs) and SONET/SDH ADMs, can now participate in GMPLS signaling and set up paths to transfer data. Additionally, routers can participate in signaling optical paths across a transport network.

GMPLS labeling is also more flexible than MPLS. A GMPLS label can represent a TDM time slot, a Dense Wavelength Division Multiplexing (DWDM) wavelength (also known as a lambda), or a physical port number. The labels can be derived from physical components of the network devices, such as interfaces.

There are two service models for GMPLS. Each model determines how much visibility a client node, such as a router, has into the optical core or transport network. The first model is a user-to-network interface (UNI), which is often referred to as the overlay model. The second is known as the peer model. Juniper Networks supports both models.

To enable multilayer LSPs, GMPLS uses the following mechanisms:

• Separation of the control channel from the data channel—A new protocol called Link Management Protocol (LMP) is used to define and manage both control channels and data channels between GMPLS peers. Messages for GMPLS LSP setup are sent from one device to a peer device over an out-of-band control channel. Once the LSP setup is complete and the path is provisioned, the data channel is established and can be used to carry traffic. In GMPLS, the control channel is always separate from the data channel.
• RSVP-TE extensions for GMPLS—RSVP-TE was designed to signal the setup of packet LSPs only. The protocol has been extended to request path setup for nonpacket LSPs that use wavelengths, time slots, and fibers as potential labels.
• OSPF extensions for GMPLS—OSPF was designed to route packets to physical and logical interfaces related to a PIC. This protocol has been extended to route packets to virtual peer interfaces defined in an LMP configuration.
• Bidirectional LSPs—Unlike unidirectional LSP paths found in the standard, packet-based version of MPLS, data can travel both ways between GMPLS devices over a single LSP path. Nonpacket LSPs in GMPLS are bidirectional by default.

GMPLS is intended to bridge the gap between the traditional transport infrastructure and the IP layer. Since this protocol is supported by several network industry organizations and standards bodies, GMPLS is designed to enable multivendor interoperability and multilayer functionality. In the near future, routers will be able to make dynamic requests for extra bandwidth on demand from the optical network. Consequently, service providers envision GMPLS as a means to set up optical circuits and services dynamically instead of manually. Many industry professionals are cautiously optimistic regarding the advent of GMPLS, and Juniper Networks is pleased to continue its support for this protocol.