Unsupported CLI

This section lists unsupported CLI.

Accounting-Options Hierarchy

• On all JSeries, SRX100, SRX210, SRX220, SRX240, and SRX650 devices, the accounting, source-class, and destination-class statements in the [accounting-options] hierarchy level are not supported.

AX411 Access Point Hierarchy

• On SRX100 devices, there are command-line interface (CLI) commands for wireless LAN configurations related to the AX411 Access Point. However, at this time the SRX100 devices do not support the AX411 Access Point.

Chassis Hierarchy

• On all JSeries, SRX100, SRX210, SRX220, SRX240, and SRX650 devices, the following chassis hierarchy CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message.

  set chassis craft-lockout

  set chassis routing-engine on-disk-failure

Class-of-Service Hierarchy

• On all JSeries, SRX100, SRX210, SRX220, SRX240, and SRX650 devices, the following class-of-service hierarchy CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message.

  set class-of-service classifiers ieee-802.1ad

  set class-of-service interfaces interface-name unit 0 adaptive-shaper

Ethernet-switching Hierarchy

• On all JSeries, SRX100, SRX210, SRX220, SRX240, and SRX650 devices, the following ethernet-switching hierarchy CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message.

  set ethernet-switching-options bpdu-block disable-timeout

  set ethernet-switching-options bpdu-block interface

  set ethernet-switching-options mac-notification

  set ethernet-switching-options voip interface access-ports

  set ethernet-switching-options voip interface ge-0/0/0.0 forwarding-class

Firewall Hierarchy

• On all JSeries, SRX100, SRX210, SRX220, SRX240 and SRX650 devices, the following Firewall hierarchy CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message.

  set firewall family vpls filter 

  set firewall family mpls dialer-filter d1 term

Interfaces CLI Hierarchy

On all JSeries, SRX100, SRX210, SRX220, SRX240, and SRX650 devices, the following interface hierarchy CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message.

• Aggregated Interface CLI
• ATM Interface CLI
• Ethernet Interfaces
• GRE Interface CLI
• IP Interface CLI
• LSQ Interface CLI
• PT Interface CLI
• T1 Interface CLI
• VLAN Interface CLI

Aggregated Interface CLI

• The following CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message.

  request lacp link-switchover ae0

  set interfaces ae0 aggregated-ether-options lacp link-protection

  set interfaces ae0 aggregated-ether-options link-protection

ATM Interface CLI

• The following CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message.

  set interfaces at-1/0/0 container-options
  

  set interfaces at-1/0/0 atm-options ilmi

  set interfaces at-1/0/0 atm-options linear-red-profiles

  set interfaces at-1/0/0 atm-options no-payload-scrambler

  set interfaces at-1/0/0 atm-options payload-scrambler

  set interfaces at-1/0/0 atm-options plp-to-clp

  set interfaces at-1/0/0 atm-options scheduler-maps

  set interfaces at-1/0/0 unit 0 atm-l2circuit-mode

  set interfaces at-1/0/0 unit 0 atm-scheduler-map

  set interfaces at-1/0/0 unit 0 cell-bundle-size

  set interfaces at-1/0/0 unit 0 compression-device

  set interfaces at-1/0/0 unit 0 epd-threshold

  set interfaces at-1/0/0 unit 0 inverse-arp

  set interfaces at-1/0/0 unit 0 layer2-policer

  set interfaces at-1/0/0 unit 0 multicast-vci

  set interfaces at-1/0/0 unit 0 multipoint

  set interfaces at-1/0/0 unit 0 plp-to-clp

  set interfaces at-1/0/0 unit 0 point-to-point

  set interfaces at-1/0/0 unit 0 radio-router

  set interfaces at-1/0/0 unit 0 transmit-weight

  set interfaces at-1/0/0 unit 0 trunk-bandwidth

Ethernet Interfaces

• The following CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message.

  set interfaces ge-0/0/1 gigether-options ignore-l3-incompletes

  set interfaces ge-0/0/1 gigether-options mpls

  set interfaces ge-0/0/0 stacked-vlan-tagging

  set interfaces ge-0/0/0 native-vlan-id

  set interfaces ge-0/0/0 radio-router

  set interfaces ge-0/0/0 unit 0 interface-shared-with 

  set interfaces ge-0/0/0 unit 0 input-vlan-map

  set interfaces ge-0/0/0 unit 0 output-vlan-map

  set interfaces ge-0/0/0 unit 0 layer2-policer

  set interfaces ge-0/0/0 unit 0 accept-source-mac

  set interfaces fe-0/0/2 fastether-options source-address-filter

  set interfaces fe-0/0/2 fastether-options source-filtering

  set interfaces ge-0/0/1 passive-monitor-mode

GRE Interface CLI

• The following CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message.

  set interfaces gr-0/0/0 unit 0 ppp-options

  set interfaces gr-0/0/0 unit 0 layer2-policer

IP Interface CLI

• The following CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message.

  set interfaces ip-0/0/0 unit 0 layer2-policer

  set interfaces ip-0/0/0 unit 0 ppp-options

  set interfaces ip-0/0/0 unit 0 radio-router

LSQ Interface CLI

• The following CLI commands are not supported. However, if you enter these commands in the CLI editor, they appear to succeed and do not display an error message.

  set interfaces lsq-0/0/0 unit 0 layer2-policer

  set interfaces lsq-0/0/0 unit 0 family ccc

  set interfaces lsq-0/0/0 unit 0 family tcc

  set interfaces lsq-0/0/0 unit 0 family vpls

  set interfaces lsq-0/0/0 unit 0 multipoint

  set interfaces lsq-0/0/0 unit 0 point-to-point 

  set interfaces lsq-0/0/0 unit 0 radio-router