PIM Background
Basic PIM Network Components
PIM Modes of Operation
PIM Dense Mode Overview
PIM Sparse Mode Overview
PIM Source-Specific Mode Overview
Mixing PIM Sparse and Dense Modes
Protocol Independent Multicast Overview
PIM Sparse Mode
Designated Router
Rendezvous Point
RP Mapping Options
Building an RPT Between RP and Receivers
PIM Sparse-Mode Source Registration
SPT Cutover
SPT Cutover Control
PIM SSM
PIM Dense Mode
PIM Sparse-Dense Mode
RP Mapping with Anycast RP
Multicast over Layer 3 VPNs
Dual PIM Multicast VPNs
MBGP-Based Multicast VPN Trees
Tunnel Services PICs and Multicast
Filtering Multicast Messages
Filtering MAC Addresses
Filtering RP/DR Register Messages
Filtering MSDP SA Messages
Embedded RP for IPv6 Multicast
PIM Mode-Independent Configuration Overview
Overview of BFD Authentication for PIM
PIM Configuration Statements
Changing the PIM Version
Configuring Interface Priority to Become the PIM Designated Router
Configuring PIM Designated Router Election on Point-to-Point Links
Modifying the PIM Hello Interval
Configuring Interface-Level PIM Neighbor Policies
Configuring a PIM RPF Routing Table
Filtering Outgoing PIM Join Messages
Filtering Incoming PIM Join Messages
Preserving Multicast Performance by Disabling Response to the ping Utility
Configuring the BFD Protocol for PIM
Configuring BFD Authentication for PIM
Configuring Nonstop Active Routing with PIM
Disabling PIM
Configuring PIM Trace Options
Configuring PIM Dense Mode Properties
Configuring PIM Sparse-Dense Mode Properties
Minimum PIM Sparse Mode Configuration
Enabling PIM Sparse Mode
Configuring PIM Sparse Mode Graceful Restart
Configuring Local PIM RPs
Configuring Static PIM RPs
Configuring PIM Bootstrap Properties
Configuring PIM Auto-RP
Configuring Register Message Filtering on a PIM RP or DR
Configuring the Interface to Accept Traffic from a Remote Source
Configuring PIM Join Load Balancing
Modifying the Join State Timeout
Enabling Join Suppression
Configuring PIM Embedded RP for IPv6
Configuring the PIM Assert Timeout
Configuring the PIM SPT Threshold Policy
Configuring Any-Source Multicast for Draft-Rosen VPNs
Load Balancing Multicast Tunnel Interfaces Among Available PICs
Example: Configuring PIM Dense Mode
Example: Configuring PIM Sparse-Dense Mode
Example: Configuring PIM Sparse Mode
Example: Configuring PIM Anycast with or without MSDP
Example: Configuring PIM BSR Filters
Example: Filtering Incoming PIM Join Messages
Example: Configuring Register Message Filters on PIM RPs and DRs
Example: Configuring Externally Facing PIM Border Routers
Example: Tracing PIM Protocol Traffic
Example: Rejecting PIM Bootstrap Messages at the Boundary of a PIM Domain
Example: Configuring PIM Dense Mode over Layer 3 VPNs
Example: Configuring PIM Sparse-Dense Mode over Layer 3 VPNs
Example: Configuring PIM Sparse Mode over Layer 3 VPNs
Example: Configuring PIM Sparse Mode over an IPsec VPN
accept-remote-source
address
algorithm
anycast-pim
assert-timeout
authentication
auto-rp
bfd-liveness-detection
bootstrap
bootstrap-export
bootstrap-import
bootstrap-priority
dense-groups
disable
dr-election-on-p2p
dr-register-policy
embedded-rp
export
family
graceful-restart
group-ranges
hello-interval
hold-time
import
infinity
interface
join-load-balance
join-prune-timeout
key-chain
local
local-address
loose-check
mapping-agent-election
maximum-rps
minimum-interval
minimum-receive-interval
mode
multiplier
neighbor-policy
override-interval
pim
priority
propagation-delay
reset-tracking-bit
restart-duration
rib-group
rp
rp-register-policy
rp-set
spt-threshold
static
traceoptions
tunnel-devices
version
vpn-group-address
http://kb.juniper.net/
