encapsulation (Physical Interface)
Syntax
Hierarchy Level
Release Information
Statement introduced before Junos OS Release 7.4.
Description
Physical link-layer encapsulation type.
Default
PPP encapsulation.
Options
atm-ccc-cell-relay—Use ATM cell-relay encapsulation.
atm-pvc—Use ATM PVC encapsulation.
cisco-hdlc—Use Cisco-compatible HDLC framing.
cisco-hdlc-ccc—Use Cisco-compatible HDLC framing on CCC circuits.
cisco-hdlc-tcc—Use Cisco-compatible HDLC framing on TCC circuits for connecting unlike media.
ethernet-ccc—Use Ethernet CCC encapsulation on Ethernet interfaces that must accept packets carrying standard TPID values.
ethernet-over-atm—As defined in RFC 1483, this encapsulation type allows ATM interfaces to connect to devices that support only bridged-mode protocol data units (PDUs). The Junos OS does not completely support bridging, but accepts BPDU packets as a default gateway. If you use the router as an edge device, then the router acts as a default gateway. It accepts Ethernet LLC/SNAP frames with IP or ARP in the payload and drops the rest. For packets destined the Ethernet LAN, a route lookup is done by use of the destination IP address. If the route lookup yields a full address match, the packet is encapsulated with an LLC/SNAP and MAC header, and the packet is forwarded to the ATM interface.
ethernet-tcc—For interfaces that carry IPv4 traffic, use Ethernet TCC encapsulation on interfaces that must accept packets carrying standard Tag Protocol Identifier (TPID) values. Ethernet TCC is not currently supported on Fast Ethernet 48-port PICs.
ethernet-vpls—Use Ethernet VPLS encapsulation on Ethernet interfaces that have VPLS enabled and that must accept packets carrying standard TPID values.
extended-frame-relay-ccc—Use Frame Relay encapsulation on CCC circuits. This encapsulation type allows you to dedicate DLCIs 1 through 1022 to CCC.
extended-frame-relay-tcc—Use Frame Relay encapsulation on TCC circuits to connect unlike media. This encapsulation type allows you to dedicate DLCIs 1 through 1022 to TCC.
extended-vlan-ccc—Use extended VLAN encapsulation on CCC circuits with Gigabit Ethernet and 4-port Fast Ethernet interfaces that must accept packets carrying 802.1Q values.
extended-vlan-tcc—For interfaces that carry IPv4 traffic, use extended VLAN encapsulation on TCC circuits with Gigabit Ethernet interfaces on which you want to use 802.1Q tagging. Extended Ethernet TCC is not currently supported on Fast Ethernet 48-port PICs.
extended-vlan-vpls—Use extended VLAN VPLS encapsulation on Ethernet interfaces that have VLAN 802.1Q tagging and VPLS enabled and that must accept packets carrying TPIDs 0x8100, 0x9100, and 0x9901.
flexible-ethernet-services—For Gigabit Ethernet intelligent queuing interfaces only, use flexible Ethernet services encapsulation when you want to configure multiple per-unit Ethernet encapsulations. This encapsulation type allows you to configure any combination of routed, TCC, CCC, and VPLS encapsulations on a single physical port.
flexible-frame-relay—For intelligent queuing interfaces only, use flexible Frame Relay encapsulation when you want to configure multiple per-unit Frame Relay encapsulations. This encapsulation type allows you to configure any combination of TCC, CCC, or standard Frame Relay encapsulations on a single physical port. Also, each logical interface can have any DLCI value in the range 1 through 1022.
frame-relay—Use Frame Relay encapsulation.
frame-relay-ccc—Use plain Frame Relay encapsulation or Frame Relay encapsulation on circuit cross-connect (CCC) circuits.
frame-relay-port-ccc—Use Frame Relay port CCC encapsulation to transparently carry all the DLCIs between two CE routers without explicitly configuring each DLCI on the two PE routers with Frame Relay transport. When you use this encapsulation type, you can configure the family ccc only.
frame-relay-tcc—Use Frame Relay encapsulation on TCC circuits to connect unlike media.
multilink-frame-relay-uni-nni—Use MLFR user-to-network (UNI) network-to-network (NNI) encapsulation. This encapsulation is used only on link services interfaces functioning as FRF.16 bundles and their constituent T1 or E1 interfaces.
ppp—Use serial PPP encapsulation.
ppp-ccc—Use serial PPP encapsulation on CCC circuits. When you use this encapsulation type, you can configure the family ccc only.
ppp-tcc—Use serial PPP encapsulation on TCC circuits for connecting unlike media. When you use this encapsulation type, you can configure the family tcc only.
vlan-ccc—Use Ethernet VLAN encapsulation on CCC circuits.
vlan-vpls—Use VLAN VPLS encapsulation on Ethernet interfaces with VLAN tagging and VPLS enabled. Interfaces with VLAN VPLS encapsulation accept packets carrying standard TPID values only.
Required Privilege Level
interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration.
