Introduction to Layer 2 Circuit Protect Interfaces Example
This example illustrates how
you might configure a Layer 2 circuit with protect interfaces.
Protect interfaces act as backups for their associated interfaces.
The primary interface has priority over the protect interface and
carries network traffic as long as it is functional. If the primary
interface fails, the protect interface is activated. These interfaces
can also share the same virtual path identifier (VPI) or virtual circuit
identifier (VCI).
Figure 1 shows the network topology used in this example.
The following sections
describe how to configure a Layer 2 circuit to use a protect
interface:
Configuring Router PE1
Configure an interface for traffic to Router CE1 from Router
PE1 at the [edit interfaces] hierarchy level:
[edit interfaces]so-0/2/2 {description "Router CE1 so-0/2/2";no-keepalives;encapsulation frame-relay-ccc;unit 1 {encapsulation frame-relay-ccc;point-to-point;dlci 600;}unit 2 {encapsulation frame-relay-ccc;point-to-point;dlci 602;}}
Configure an interface for traffic to Router CE1 from Router
PE1 at the [edit interfaces] hierarchy level. Logical interface so-0/2/0.2 acts as the protect interface for so-0/2/2.2, and logical interface so-0/2/0.1 acts as the protect interface
for so-0/2/2.1:
[edit interfaces]so-0/2/0 {description "to Router CE1 so-0/3/0";no-keepalives;encapsulation frame-relay-ccc;unit 1 {encapsulation frame-relay-ccc;dlci 600;}unit 2 {encapsulation frame-relay-ccc;dlci 602;}}
Configure an interface for traffic to Router PE2 from Router
PE1 at the [edit interfaces] hierarchy level:
[edit interfaces]so-0/2/1 {description "to Router PE2 so-1/0/1";unit 0 {family inet {address 100.100.40.22/32 {destination 100.100.40.23;}}family iso;family mpls;}}
Configure an interface for traffic to Router PE2 from Router
PE1 at the [edit interfaces] hierarchy level:
[edit interfaces]so-0/2/3 {description "Router PE2 so-1/0/3";unit 0 {family inet;family iso;family mpls;}lo0 {unit 0 {family inet {address 127.0.0.1/32;address 10.100.40.200/32;}family iso {address 47.0005.80ff.f800.0000.0108.0001.1921.6800.4213.00;}}}}
Configure the Layer 2 circuit by including the l2circuit statement at the [edit protocols] hierarchy level. The
logical interfaces for the Layer 2 circuits and their corresponding
protect interfaces are included here:
[edit protocols]l2circuit {neighbor 10.100.40.210 {interface so-0/2/2.2 {protect-interface so-0/2/0.2;virtual-circuit-id 2;no-control-word;}interface so-0/2/2.1 {protect-interface so-0/2/0.1;virtual-circuit-id 1;no-control-word;}}}
Configuring Router PE2
Configure an interface for traffic to Router CE2 from Router
PE2:
[edit interfaces]so-1/0/0 {description "to Router CE2 so-0/2/0";no-keepalives;encapsulation frame-relay-ccc;unit 1 {encapsulation frame-relay-ccc;point-to-point;dlci 700;}unit 2 {encapsulation frame-relay-ccc;point-to-point;dlci 702;}}
Configure an interface for traffic to Router PE1 from Router
PE2:
[edit interfaces]so-1/0/1 {description "to Router PE1 so-0/2/1";unit 0 {family inet {address 100.100.40.23/32 {destination 100.100.40.22;}}family iso;family mpls;}}
Configure an interface for traffic to Router PE1 from Router
PE2:
[edit interfaces]so-1/0/3 {description "to Router PE1 so-0/2/3";unit 0 {family inet;family iso;family mpls;}}lo0 {unit 0 {family inet {address 127.0.0.1/32;address 10.100.40.210/32;}family iso {address 47.0005.80ff.f800.0000.0108.0001.1921.6800.4216.00;}}}
Configure the Layer 2 circuit at the [edit protocols] hierarchy level:
[edit protocols]l2circuit {neighbor 10.100.40.200 {interface so-1/0/0.1 {virtual-circuit-id 1;no-control-word;}interface so-1/0/0.2 {virtual-circuit-id 2;no-control-word;}}}
Configuring Router CE1
Configure an interface for traffic to Router PE1 from Router
CE1:
[edit interfaces]so-0/3/0 {description "to Router PE1 so-0/2/0";no-keepalives;encapsulation frame-relay;unit 1 {dlci 601;family inet {address 12.12.12.1/24;}}}
Configure an interface for traffic to Router PE1 from Router
CE1:
[edit interfaces]so-0/3/1 {description "Router PE1 so-0/2/2";no-keepalives;encapsulation frame-relay;unit 0 {dlci 600;family inet {address 10.10.10.1/24;address 11.1.1.1/24;}family iso;family mpls;}unit 2 {dlci 602;family inet {address 13.13.13.1/24;}}}
Configuring Router CE2
Configure an interface for traffic to Router PE2 from Router
CE2:
[edit interfaces]so-0/2/0 {description "to Router PE2 so-1/0/0";no-keepalives;encapsulation frame-relay;unit 1 {dlci 700;family inet {address 10.10.10.2/24;address 11.1.1.2/24;address 12.12.12.2/24;}}unit 2 {dlci 702;family inet {address 13.13.13.2/24;}}}
Published: 2010-07-16
