• Related Topics
• Understanding Fault Isolation and Detection in a PBB using Connectivity Fault Management for MX Series Routers
• Understanding Provider Backbone Bridging on MX Series Routers
• Example: Configuring E-LINE and E-LAN Services for a PBB Network on MX series Routers
• Example: Configuring CoS for a PBB Network on MX Series Routers

Example: Configuring Connectivity Fault Management for a PBB Network on MX Series Routers

Requirements

This example uses the following hardware and software components:

• JUNOS Release 10.0 or later for MX Series routers
• Eight MX Series routers in a PBB configuration

Before you configure the routers for PBB and services, be sure you have:

• Installed the MX Series router.
• Performed the initial router configuration.
• Performed the PBB configuration for Ethernet private line (E-LINE) and Ethernet transparent LAN (E-LAN) services. For more information, refer to “Example: Configuring E-LINE and E-LAN Services for a PBB Network on MX series Routers”.

Overview and Topology

There are two different networks that need to be configured for CFM in this example:

• A provider backbone bridge network (PBBN).
• Provider bridged networks (PBNs) that include PBN1, PBN2, and PBN3.

This example uses a series of maintenance end points (MEPs) and maintenance intermediate points (MIPs). MIPs respond to the OAM processes initiated by the MEPs. Using MEPs and MIPs, CFM provides end-to-end connectivity in the PBBN because it can exactly pinpoint a failure in the topology.

Figure 1 displays the topology for the PBBN. The PBBN connect the PBNs and provides services to the PBNs. Two backbone core bridges (BCBs) are connected to PBN1, PBN2, and PBN3. Operation, Administration, and Maintenance (OAM) in the PBBN is limited to fault detection in the PBBN.

Table 1 shows the maintenance end points (MEPs) and maintenance intermediate points (MIPs) that are configured for each router in the PBBN. The PBBN is configured with VLAN 3150 and 3350. CFM must be configured for monitoring the connectivity in both the VLANs. To do this, configure a MEP for each VLAN at the endpoints (BEBs), and configure a MIP for each VLAN on the core bridges (BCBs).

To configure a MIP for level x, the maintenance domain default-x is configured on the router. For example, if MEPs in the PBBN are configured at level 3, the MIP is configured as default-3.

Note: CFM in the PBBN is used to check the connectivity in the PBBN domain only, and packets are never leaked to the PBN.

Figure 2 displays the topology for PBN. BEB1, BEB2, BEB3, and BEB4 are connected to customer edge switches ES1, ES3, and ES4.

The PBN is configured with VLAN 500 and 600. CFM must be configured for monitoring the connectivity in both the VLANs. To do this, configure a MEP for each VLAN at the endpoints (ESs), and configure a MIP for each VLAN on the BEBs.

Comparing both topologies, notice that the BEBs are actually part of both the PBN and the PBBN. They perform the function of a MEP in the PBBN, but perform the function of a MIP in the PBN and participate in multiple maintenance domains. In comparison, BCBs in the PBBN participate in one maintenance domain and ESs in the PBN participate in one maintenance domain.

Note: CFM on the PBN is used to check the connectivity in the PBN domain—these packets are simply tunneled in the PBBN domain as data packets.

Table 2 shows the MEPs and MIPs that are configured in the PBN.

Note: MX Series router ES3 (Dolcetto) is visible in the topology, but is not part of the CFM configuration example.

Configuring Connectivity Fault Management for a PBBN

To configure connectivity fault management on MX Series routers in a provider backbone bridge network, perform these tasks:

• Configuring a MEP on BEB1 (Sangiovese)
• Configuring a MEP on BEB2 (Barbera)
• Configuring a MEP on BEB3 (Malbec)
• Configuring a MEP on BEB4 (Cubs)
• Configuring a MIP on BCB1 (Syrah)
• Configuring a MIP on BCB2 (Cabernet)

Configuring a MEP on BEB1 (Sangiovese)

CLI Quick Configuration

To quickly configure a MEP for BEB1, copy the following commands and paste them into the router terminal window:

Step-by-Step Procedure

To configure a MEP for BEB1:

1. Create a maintenance domain at level 5 for PBBN monitoring (here, the maintenance domain is pbbn):
   
   

   [edit protocols oam]
user@beb1# set ethernet connectivity-fault-management maintenance-domain pbbn level 5


2. Configure the continuity check interval for the maintenance association (here, vlan3350). The continuity check protocol is used for fault detection by a Maintenance End Point (MEP). The MEP periodically sends continuity check multicast messages, and receiving MEPs use the CC messages to build a MEP database of all MEPs in the maintenance association.
   
   

   [edit protocols oam]
user@beb1# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3350 continuity-check interval 1s

3. Configure a MEP with the same maintenance association identifier and maintenance domain level (here, vlan3150 and pbbn) and associate them to VLAN 3150 and the pseudo-logical interface cbp0.0).
   
   

   [edit protocols oam]
user@beb1# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3350 mep 100 interface vlan 3350
user@beb1# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3350 mep 100 interface cbp0.0


   Note: When you configure PBB, a customer backbone port (cbp) pseudo-logical interface is configured for the B-component of the BEB. This permits multiple customer routing instances to be associated with a single PBBN provider routing instance.

4. Configure the direction in which CFM packets are transmitted for the MEP. Direction up CCMs are transmitted out of every logical interface that is part of the same bridge (here, direction is specified as up).
   
   

   [edit protocols oam]
user@beb1# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3350 mep 100 direction up

5. Configure automatic discovery to enable the MEP to accept continuity check messages from all remote MEPs of the same maintenance association.
   
   

   [edit protocols oam]
user@beb1# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3350 mep 100 auto-discovery

6. Configure the continuity check interval for the maintenance association (here, vlan3150). The continuity check protocol is used for fault detection by a MEP. The MEP periodically sends continuity check multicast messages, and receiving MEPs use the CC messages to build a MEP database of all MEPs in the maintenance association.
   
   

   [edit protocols oam]
user@beb1# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 continuity-check interval 1s

7. Configure a MEP with the same maintenance association identifier and maintenance domain level (here, vlan3150 and pbbn).
   
   

   [edit protocols oam]
user@beb1# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 100 interface vlan 3350

8. Configure the direction in which CFM packets are transmitted for the MEP. Direction up CCMs are transmitted out of every logical interface that is part of the same bridge (here, direction is specified as up).
   
   

   [edit protocols oam]
user@beb1# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 100 direction up

9. Configure automatic discovery to enable the MEP to accept continuity check messages from all remote MEPs of the same maintenance association.

   Note: You can also use the command remote-mep to specify a remote MEP.

   
   

   [edit protocols oam]
user@beb1# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 100 auto-discovery


Results

Check the results of the configuration:

Configuring a MEP on BEB2 (Barbera)

CLI Quick Configuration

To quickly configure a MEP for BEB2, copy the following commands and paste them into the router terminal window:

Step-by-Step Procedure

To configure a MEP for BEB2:

1. Create a maintenance domain at level 5 for PBBN monitoring (here, the maintenance domain is pbbn):
   
   

   [edit protocols oam]
user@beb2# set protocols oam ethernet connectivity-fault-management maintenance-domain pbbn level 5


2. Configure the continuity check (CC) interval for the maintenance association (here, vlan3150). The continuity check protocol is used for fault detection by a MEP. The MEP periodically sends continuity check multicast messages, and receiving MEPs use the CC messages to build a MEP database of all MEPs in the maintenance association.
   
   

   [edit protocols oam ]
user@beb2# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 continuity-check interval 1s

3. Configure a MEP with the same maintenance association identifier and maintenance domain level (here, vlan3150 and pbbn) and associate them to VLAN 3150 and the pseudo-logical interface cbp0.0).
   
   

   [edit protocols oam ]
user@beb2# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 101 interface vlan 3150
user@beb2# set cfm-pbbn protocols oam ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 101 interface cbp0.0


   Note: When you configure PBB, a customer backbone port (cbp) pseudo-logical interface is configured for the B-component of the BEB. This permits multiple customer routing instances to be associated with a single PBBN provider routing instance.

4. Configure the direction in which CFM packets are transmitted for the MEP. Direction up CCMs are transmitted out of every logical interface that is part of the same bridge (here, direction is specified as up).
   
   

   [edit protocols oam ]
user@beb2# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 101 direction up

5. Configure automatic discovery to enable the MEP to accept continuity check messages from all remote MEPs of the same maintenance association.
   
   

   [edit protocols oam ]
user@beb2# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 101 auto-discovery


Results

Check the results of the configuration:

Configuring a MEP on BEB3 (Malbec)

CLI Quick Configuration

To quickly configure a MEP on BEB3, copy the following commands and paste them into the router terminal window:

Step-by-Step Procedure

To configure a MEP on BEB3:

1. Create a maintenance domain at level 5 for PBBN monitoring (here, the maintenance domain is pbbn-elan):
   
   

   [edit groups]
user@beb3# set protocols oam ethernet connectivity-fault-management maintenance-domain pbbn-elan level 5


2. Configure a MEP with the same maintenance association identifier and maintenance domain level (here, vlan3350 and pbbn-elan and associate them to VLAN 3150 and the pseudo-logical interface cbp0.0.
   
   

   [edit protocols oam]
user@beb3# set ethernet connectivity-fault-management maintenance-domain pbbn-elan maintenance-association vlan3350 mep 102 interface vlan 3350
user@beb3# set ethernet connectivity-fault-management maintenance-domain pbbn-elan maintenance-association vlan3350 mep 101 interface cbp0.0


   Note: When you configure PBB, a customer backbone port (cbp) pseudo-logical interface is configured for the B-component of the BEB. This permits multiple customer routing instances to be associated with a single PBBN provider routing instance.

3. Configure the direction in which CFM packets are transmitted for the MEP. Direction up CCMs are transmitted out of every logical interface that is part of the same bridge (here, direction is specified as up).
   
   

   [edit protocols oam]
user@beb3# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 101 direction up

4. Configure automatic discovery to enable the MEP to accept continuity check messages from all remote MEPs of the same maintenance association.
   
   

   [edit protocols oam]
user@beb3# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 101 auto-discovery


Results

Check the results of the configuration:

Configuring a MEP on BEB4 (Cubs)

CLI Quick Configuration

To quickly configure a MEP for BEB4, copy the following commands and paste them into the router terminal window:

Step-by-Step Procedure

To configure a MEP for BEB4:

1. Create a maintenance domain at level 5 for PBBN monitoring (here, the maintenance domain is pbbn):
   
   

   [edit protocols oam]
user@beb4# set ethernet connectivity-fault-management maintenance-domain pbbn level 5


2. Configure the continuity check interval for the maintenance association (here, vlan3350). The continuity check protocol is used for fault detection by a MEP. The MEP periodically sends continuity check multicast messages, and receiving MEPs use the CC messages to build a MEP database of all MEPs in the maintenance association.
   
   

   [edit protocols oam]
user@beb4# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3350 continuity-check interval 1s

3. Configure a MEP with the same maintenance association identifier and maintenance domain level (here, vlan3150 and pbbn) and associate them to VLAN 3150 and the pseudo-logical interface cbp0.0.
   
   

   [edit protocols oam]
user@beb4# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3350 mep 102 interface vlan 3350
user@beb4# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3350 mep 102 interface cbp0.0


   Note: When you configure PBB, a customer backbone port (cbp) pseudo-logical interface is configured for the B-component of the BEB. This permits multiple customer routing instances to be associated with a single PBBN provider routing instance.

4. Configure the direction in which CFM packets are transmitted for the MEP. Direction up CCMs are transmitted out of every logical interface that is part of the same bridge (here, direction is specified as up).
   
   

   [edit protocols oam]
user@beb4# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3350 mep 102 direction up

5. Configure automatic discovery to enable the MEP to accept continuity check messages from all remote MEPs of the same maintenance association.
   
   

   [edit protocols oam]
user@beb4# set protocols oam ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3350 mep 102 auto-discovery

6. Configure the continuity check interval for the maintenance association (here, vlan3150). The continuity check protocol is used for fault detection by a MEP. The MEP periodically sends continuity check multicast messages, and receiving MEPs use the CC messages to build a MEP database of all MEPs in the maintenance association.
   
   

   [edit protocols oam]
user@beb4# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 continuity-check interval 1s

7. Configure a MEP with the same maintenance association identifier and maintenance domain level (here, vlan3150 and pbbn).
   
   

   [edit protocols oam]
user@beb4# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 102 interface vlan 3150

8. Configure the direction in which CFM packets are transmitted for the MEP. Direction up CCMs are transmitted out of every logical interface that is part of the same bridge (here, direction is specified as up).
   
   

   [edit protocols oam]
user@beb4# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 102 direction up

9. Configure automatic discovery to enable the MEP to accept continuity check messages from all remote MEPs of the same maintenance association.
   
   

   [edit protocols oam]
user@beb4# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association vlan3150 mep 102 auto-discovery


Results

Check the results of the configuration:

Configuring a MIP on BCB1 (Syrah)

CLI Quick Configuration

To quickly configure a MIP for BCB1, copy the following commands and paste them into the router terminal window:

Step-by-Step Procedure

To configure a MIP for BCB1:

1. Configure a maintenance domain default-5 and the bridge domain eline-bvlan and associate them to VLAN ID 3150.
   
   

   [edit protocols oam]
user@bcb1# set ethernet connectivity-fault-management maintenance-domain default-5 virtual-switch pbbn-1 bridge-domain eline-bvlan vlan-id 3150

2. Specify the OAM Ethernet CFM maintenance domain MIP half functions (here, the MIP half function is default):
   
   

   [edit protocols oam]
user@bcb1# ethernet connectivity-fault-management maintenance-domain default-5 mip-half-function default


   Note: Whenever a MIP is configured and a bridge domain is mapped to multiple maintenance domains (MDs) or maintenance associations (MAs), it is essential that the mip-half-function value for all MDs and MAs be the same.

Results

Check the results of the configuration:

Configuring a MIP on BCB2 (Cabernet)

CLI Quick Configuration

To quickly configure a MIP for BCB2, copy the following commands and paste them into the router terminal window:

Step-by-Step Procedure

To configure a MIP for BCB2:

1. Configure maintenance domain default-5 and the bridge domain eline-bvlan and associate them to VLAN ID 3150.
   
   

   [edit protocols oam]
user@bcb2# set ethernet connectivity-fault-management maintenance-domain default-5 virtual-switch pbbn-1 bridge-domain eline-bvlan vlan-id 3150

2. Specify the OAM Ethernet CFM maintenance domain MIP half functions (here, the MIP half function is default):
   
   

   [edit protocols oam]
user@bcb2# ethernet connectivity-fault-management maintenance-domain default-5 mip-half-function default


   Note: Whenever a MIP is configured and a bridge domain is mapped to multiple maintenance domains (MDs) or maintenance associations (MAs), it is essential that the mip-half-function value for all MDs and MAs be the same.

Results

Check the results of the configuration:

Configuring Connectivity Fault Management for a PBN

To configure connectivity fault management on MX Series routers in a PBN, perform these tasks:

• Configuring a MIP on BEB1 (Sangiovese)
• Configuring a MIP on BEB2 (Barbera)
• Configuring a MIP on BEB4 (Cubs)
• Configuring a MEP on ES1 (Pinot Noir)
• Configuring a MEP on ES4 (Reds)

Configuring a MIP on BEB1 (Sangiovese)

CLI Quick Configuration

To quickly configure a MIP for BEB1, copy the following commands and paste them into the router terminal window:

Step-by-Step Procedure

To configure a MIP for BEB1:

1. To enable CFM at the B-VLAN level, specify the B-VLAN routing instance name, the B-VLAN ID, and the service group (here, the routing instance is pbn-1-for-eline, the B-VLAN IDs are 1200 and 2100, and the service group is eline-svlans):
   
   

   [edit protocols oam ethernet connectivity-fault-management]
set maintenance-domain default-3 virtual-switch pbn-1-for-eline bridge-domain eline-svlans vlan-id 1200
set maintenance-domain default-3 virtual-switch pbn-1-for-eline bridge-domain eline-svlans vlan-id 2100
2. Specify the OAM Ethernet CFM maintenance domain MIP half functions (here, the MIP half function is default):
   
   

   [edit protocols oam ethernet connectivity-fault-management]
user@beb1# maintenance-domain default-3 mip-half-function default


   Note: Whenever a MIP is configured and a bridge domain is mapped to multiple maintenance domains (MDs) or maintenance associations (MAs), it is essential that the mip-half-function value for all MDs and MAs be the same.

Results

Check the results of the configuration:

Configuring a MIP on BEB2 (Barbera)

CLI Quick Configuration

To quickly configure a MIP for BEB2, copy the following commands and paste them into the router terminal window:

Step-by-Step Procedure

To configure a MIP for BEB2:

1. Create a MIP for the PBN (here, at level default-3):
   
   

   [edit protocols oam ]
set ethernet connectivity-fault-management maintenance-domain default-3 virtual-switch pbn-1-for-eline bridge-domain eline-svlans vlan-id 1200
set maintenance-domain default-3 virtual-switch pbn-1-for-eline bridge-domain eline-svlans vlan-id 2100
2. Specify the OAM Ethernet CFM maintenance domain MIP half functions (here, the MIP half function is default):
   
   

   [edit protocols oam ]
user@beb2# ethernet connectivity-fault-management maintenance-domain default-3 mip-half-function default


   Note: Whenever a MIP is configured and a bridge domain is mapped to multiple MDs or MAs, it is essential that the mip-half-function value for all MDs and MAs be the same.

Results

Check the results of the configuration:

Configuring a MIP on BEB4 (Cubs)

CLI Quick Configuration

To quickly configure a MIP for BEB4, copy the following commands and paste them into the router terminal window:

Step-by-Step Procedure

To configure a MIP for BEB4:

1. To enable CFM at the B-VLAN level, specify the B-VLAN routing instance name, the B-VLAN ID, and the service group (here, the routing instance is pbn-3-for-eline the B-VLAN IDs are 1200 and 2100, and the service group is eline-svlans):
   
   

   [edit protocols oam]
set ethernet connectivity-fault-management maintenance-domain default-3 virtual-switch pbn-3-for-eline bridge-domain eline-svlans vlan-id 1200
set ethernet connectivity-fault-management maintenance-domain default-3 virtual-switch pbn-3-for-eline bridge-domain eline-svlans vlan-id 2100
2. Specify the OAM Ethernet CFM maintenance domain MIP half functions (here, the MIP half function is default):
   
   

   [edit protocols oam ]
user@beb4# ethernet connectivity-fault-management maintenance-domain default-3 mip-half-function default


   Note: Whenever a MIP is configured and a bridge domain is mapped to multiple maintenance domains (MDs) or maintenance associations (MAs), it is essential that the mip-half-function value for all MDs and MAs be the same.

Results

Check the results of the configuration:

Configuring a MEP on ES1 (Pinot Noir)

CLI Quick Configuration

To quickly configure a MEP for ES1, copy the following commands and paste them into the router terminal window:

Step-by-Step Procedure

To configure a MEP for ES1:

1. Configure the maintenance domain es-domain, a mandatory parameter that indicates the nesting relationship between various maintenance domains and is embedded in each of the CFM frames:
   
   

   [edit protocols oam]
user@es1# set protocols oam ethernet ethernet connectivity-fault-management maintenance-domain es-domain level 3

2. Configure the continuity check interval for the maintenance association (here, vlan3350). The continuity check protocol is used for fault detection by a MEP. The MEP periodically sends continuity check multicast messages, and receiving MEPs use the CC messages to build a MEP database of all MEPs in the maintenance association.
   
   

   [edit protocols oam]
user@es1# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-1continuity-check interval 1s

3. Configure a MEP with the same maintenance domain and maintenance association identifier (here, es-domain and eline-1) and associate them to VLAN 500 and the pseudo-logical interface ge-1/1/0.0.
   
   

   [edit protocols oam]
user@es1# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-1 mep 1 interface ge-1/1/0.0
user@es1# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-1 mep 1 interface vlan 500

4. Configure the direction in which CFM packets are transmitted for the MEP. Direction up CCMs are transmitted out of every logical interface that is part of the same bridge (here, direction is specified as up).
   
   

   [edit protocols oam]
user@es1# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-1 mep 1 direction up

5. Configure automatic discovery to enable the MEP to accept continuity check messages from all remote MEPs of the same maintenance association.
   
   

   [edit protocols oam]
user@es1# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association eline-1 mep 1 auto-discovery

6. Configure the continuity check interval for the maintenance association (here, vlan3150). The continuity check protocol is used for fault detection by a MEP. The MEP periodically sends continuity check multicast messages, and receiving MEPs use the CC messages to build a MEP database of all MEPs in the maintenance association.
   
   

   [edit protocols oam]
user@es1# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-2 continuity-check interval 1s

7. Configure a MEP with the same maintenance domain and maintenance association identifier (here, es-domain and eline-2) and associate them to VLAN 500 and the pseudo-logical interface ge-1/0/3.6.
   
   

   [edit protocols oam]
user@es1# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-2 mep 1 interface ge-1/1/0.0
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-2 mep 1 interface vlan 600

8. Configure the direction in which CFM packets are transmitted for the MEP. Direction up CCMs are transmitted out of every logical interface that is part of the same bridge (here, direction is specified as up).
   
   

   [edit protocols oam]
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-2 mep 1 direction up

9. Configure automatic discovery to enable the MEP to accept continuity check messages from all remote MEPs of the same maintenance association.
   
   

   [edit protocols oam]
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-2 mep 1 auto-discovery


Results

Check the results of the configuration:

Configuring a MEP on ES4 (Reds)

CLI Quick Configuration

To quickly configure OAM for ES4, copy the following commands and paste them into the router terminal window:

Step-by-Step Procedure

To configure a MEP for ES4:

1. Configure the maintenance domain es-domain, a mandatory parameter that indicates the nesting relationship between various maintenance domains and is embedded in each of the CFM frames:
   
   

   [edit protocols oam]
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain level 3

2. Configure the continuity check interval for the maintenance association (here, vlan3350). The continuity check protocol is used for fault detection by a MEP. The MEP periodically sends continuity check multicast messages, and receiving MEPs use the CC messages to build a MEP database of all MEPs in the maintenance association.
   
   

   [edit protocols oam]
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-1continuity-check interval 1s

3. Configure a MEP with the same maintenance domain and maintenance association identifier (here, es-domain and eline-1) and associate them to VLAN 500 and the pseudo-logical interface ge-1/0/3.5.
   
   

   [edit protocols oam]
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-1 mep 2 interface ge-1/0/3.5
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-1 mep 2 interface vlan 500

4. Configure the direction in which CFM packets are transmitted for the MEP. Direction up CCMs are transmitted out of every logical interface that is part of the same bridge (here, direction is specified as up).
   
   

   [edit protocols oam]
user@es4# ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-1 mep 2 direction up

5. Configure automatic discovery to enable the MEP to accept continuity check messages from all remote MEPs of the same maintenance association.
   
   

   [edit protocols oam]
user@es4# set ethernet connectivity-fault-management maintenance-domain pbbn maintenance-association eline-1 mep 2 auto-discovery

6. Configure the continuity check interval for the maintenance association (here, vlan3150). The continuity check protocol is used for fault detection by a MEP. The MEP periodically sends continuity check multicast messages, and receiving MEPs use the CC messages to build a MEP database of all MEPs in the maintenance association.
   
   

   [edit protocols oam]
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-2 continuity-check interval 1s

7. Configure a MEP with the same maintenance domain and maintenance association identifier (here, es-domain and eline-2) and associate them to VLAN 500 and the pseudo-logical interface ge-1/0/3.6.
   
   

   [edit protocols oam]
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-2 mep 2 interface ge-1/0/3.6
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-2 mep 2 interface vlan 600

8. Configure the direction in which CFM packets are transmitted for the MEP. Direction up CCMs are transmitted out of every logical interface that is part of the same bridge (here, direction is specified as up).
   
   

   [edit protocols oam]
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-2 mep 2 direction up

9. Configure automatic discovery to enable the MEP to accept continuity check messages from all remote MEPs of the same maintenance association.
   
   

   [edit protocols oam]
user@es4# set ethernet connectivity-fault-management maintenance-domain es-domain maintenance-association eline-2 mep 2 auto-discovery


Results

Check the results of the configuration:

Verification

To confirm that the configuration is working properly on each router in the PBBN and PBN:

• Verify that the CC protocol is UP for VLAN 3150 and VLAN 3350 (in the PBBN) and VLAN 500 and VLAN 600 (in the PBN). The MEP should be able to discover remote MEPs in each VLAN.
• Verify the path between a pair of MEPs using the Linktrace protocol. The MIPs should respond to linktrace messages.

To confirm that the configuration is working properly, perform these tasks:

• Verifying CFM on VLAN 3150 in the PBBN
• Verifying CFM for VLAN 3350 in the PBBN
• Verifying CFM for VLAN 500 in the PBN
• Verifying CFM for VLAN 600 in the PBN

Verifying CFM on VLAN 3150 in the PBBN

Purpose

Verify the CFM configuration on the following routers that are participating in VLAN-3150 using the maintenance domain pbbn and the maintenance association vlan3150 level-5 for OAM monitoring:

• BEB1 (Sangiovese) MEP-100
• BEB2 (Barbera) MEP-101
• BEB4 (Cubs) MEP-102
• BCB1 (Syrah) MIP
• BCB2 (Cabernet) MIP

Action

Interface name: cbp0.0, vlan 3150, Interface status: Active, Link status: Up
  Maintenance domain name: pbbn, Format: string, Level: 5
    Maintenance association name: vlan3150, Format: string
    Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
    Interface status TLV: none, Port status TLV: none
    MEP identifier: 100, Direction: up, MAC address: 00:21:59:aa:78:11
    MEP status: running
    Defects:        
      Remote MEP not receiving CCM                  : no
      Erroneous CCM received                        : no
      Cross-connect CCM received                    : no
      RDI sent by some MEP                          : no
      Some remote MEP's MAC in error state          : no
    Statistics:     
      CCMs sent                                     : 14670
      CCMs received out of sequence                 : 0
      LBMs sent                                     : 0
      Valid in-order LBRs received                  : 0
      Valid out-of-order LBRs received              : 0
      LBRs received with corrupted data             : 0
      LBRs sent                                     : 0
      LTMs sent                                     : 5
      LTMs received                                 : 0
      LTRs sent                                     : 0
      LTRs received                                 : 10
      Sequence number of next LTM request           : 5
      1DMs sent                                     : 0
      Valid 1DMs received                           : 0
      Invalid 1DMs received                         : 0
      Out of sync 1DMs received                     : 0
      DMMs sent                                     : 0
      Valid DMMs received                           : 0
      Invalid DMMs received                         : 0
      DMRs sent                                     : 0
      Valid DMRs received                           : 0
      Invalid DMRs received                         : 0
    Remote MEP count: 2
      Identifier    MAC address        State    Interface
        101     00:22:83:32:d8:11       ok    ge-1/3/9.0
        102     00:1f:12:b8:38:11       ok    ge-1/3/9.0

  
  Linktrace to 00:22:83:32:d8:11, Interface : ge-1/3/9.0
      Maintenance Domain: pbbn, Level: 5 
      Maintenance Association: vlan3150, Local Mep: 100
      Transaction Identifier: 5
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     62     00:21:59:aa:74:8d         00:21:59:aa:74:84  
    2     61     00:22:83:32:d8:11         00:00:00:00:00:00       

  
   Linktrace to 00:1f:12:b8:38:11, Interface : ge-1/3/9.0
      Maintenance Domain: pbbn, Level: 5 
      Maintenance Association: vlan3150, Local Mep: 100
      Transaction Identifier: 6
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     62     00:21:59:aa:74:8d         00:21:59:aa:75:d4  
    2     61     00:1f:12:b8:38:11         00:00:00:00:00:00  

Interface name: cbp0.0, vlan 3150, Interface status: Active, Link status: Up
  Maintenance domain name: pbbn, Format: string, Level: 5
    Maintenance association name: vlan3150, Format: string
    Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
    Interface status TLV: none, Port status TLV: none
    MEP identifier: 101, Direction: up, MAC address: 00:22:83:32:d8:11
    MEP status: running
    Defects:
      Remote MEP not receiving CCM                  : no
      Erroneous CCM received                        : no
      Cross-connect CCM received                    : no
      RDI sent by some MEP                          : no
      Some remote MEP's MAC in error state          : no
    Statistics:
      CCMs sent                                     : 6021
      CCMs received out of sequence                 : 0
      LBMs sent                                     : 0
      Valid in-order LBRs received                  : 0
      Valid out-of-order LBRs received              : 0
      LBRs received with corrupted data             : 0
      LBRs sent                                     : 0
      LTMs sent                                     : 1
      LTMs received                                 : 4
      LTRs sent                                     : 4
      LTRs received                                 : 2
      Sequence number of next LTM request           : 1
      1DMs sent                                     : 0
      Valid 1DMs received                           : 0
      Invalid 1DMs received                         : 0
      Out of sync 1DMs received                     : 0
      DMMs sent                                     : 0
      Valid DMMs received                           : 0
      Invalid DMMs received                         : 0
      DMRs sent                                     : 0
      Valid DMRs received                           : 0
      Invalid DMRs received                         : 0
    Remote MEP count: 2
      Identifier    MAC address        State    Interface
        100     00:21:59:aa:78:11       ok    ge-1/3/0.0
        102     00:1f:12:b8:38:11       ok    ge-1/3/0.0

Linktrace to 00:21:59:aa:78:11, Interface : ge-1/3/0.0
      Maintenance Domain: pbbn, Level: 5 
      Maintenance Association: vlan3150, Local Mep: 101
      Transaction Identifier: 1
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     62     00:21:59:aa:74:84         00:21:59:aa:74:8d  
    2     61     00:21:59:aa:78:11         00:00:00:00:00:00  

Linktrace to 00:1f:12:b8:38:11, Interface : ge-1/3/0.0
      Maintenance Domain: pbbn, Level: 5 
      Maintenance Association: vlan3150, Local Mep: 101
      Transaction Identifier: 2
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     62     00:21:59:aa:74:84         00:21:59:aa:75:d4  
    2     61     00:1f:12:b8:38:11         00:00:00:00:00:00  

Interface name: cbp0.0, vlan 3150, Interface status: Active, Link status: Up
  Maintenance domain name: pbbn, Format: string, Level: 5
    Maintenance association name: vlan3150, Format: string
    Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
    Interface status TLV: none, Port status TLV: none
    MEP identifier: 102, Direction: up, MAC address: 00:1f:12:b8:38:11
    MEP status: running
    Defects:        
      Remote MEP not receiving CCM                  : no
      Erroneous CCM received                        : no
      Cross-connect CCM received                    : no
      RDI sent by some MEP                          : no
      Some remote MEP's MAC in error state          : no
    Statistics:     
      CCMs sent                                     : 7507
      CCMs received out of sequence                 : 0
      LBMs sent                                     : 0
      Valid in-order LBRs received                  : 0
      Valid out-of-order LBRs received              : 0
      LBRs received with corrupted data             : 0
      LBRs sent                                     : 0
      LTMs sent                                     : 1
      LTMs received                                 : 6
      LTRs sent                                     : 6
      LTRs received                                 : 2
      Sequence number of next LTM request           : 1
      1DMs sent                                     : 0
      Valid 1DMs received                           : 0
      Invalid 1DMs received                         : 0
      Out of sync 1DMs received                     : 0
      DMMs sent                                     : 0
      Valid DMMs received                           : 0
      Invalid DMMs received                         : 0
      DMRs sent                                     : 0
      Valid DMRs received                           : 0
      Invalid DMRs received                         : 0
    Remote MEP count: 2
      Identifier    MAC address        State    Interface
        100     00:21:59:aa:78:11       ok    ge-1/0/4.0
        101     00:22:83:32:d8:11       ok    ge-1/0/4.0

Linktrace to 00:21:59:aa:78:11, Interface : ge-1/0/4.0
      Maintenance Domain: pbbn, Level: 5 
      Maintenance Association: vlan3150, Local Mep: 102
      Transaction Identifier: 1
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     62     00:21:59:aa:75:d4         00:21:59:aa:74:8d  
    2     61     00:21:59:aa:78:11         00:00:00:00:00:00  

Linktrace to 00:22:83:32:d8:11, Interface : ge-1/0/4.0
      Maintenance Domain: pbbn, Level: 5 
      Maintenance Association: vlan3150, Local Mep: 102
      Transaction Identifier: 2
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     62     00:21:59:aa:75:d4         00:21:59:aa:74:84  
    2     61     00:22:83:32:d8:11         00:00:00:00:00:00  

MIP information for instance pbbn-1 eline-bvlan-vlan-3150
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  ge-2/1/5.0          5
  ge-2/3/0.0          5
  ge-2/3/9.0          5
  ge-1/3/0.0          5
  ge-1/3/9.0          5

MIP information for instance pbbn-1 eline-bvlan-vlan-3150
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  ge-2/0/6.0          5
  ge-1/3/0.0          5
  ge-1/3/9.0          5
  ge-2/3/0.0          5
  ge-2/3/9.0          5

Interface name: cbp0.0, vlan 3350, Interface status: Active, Link status: Up
  Maintenance domain name: pbbn, Format: string, Level: 5
    Maintenance association name: vlan3350, Format: string
    Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
    Interface status TLV: none, Port status TLV: none
    MEP identifier: 100, Direction: up, MAC address: 00:21:59:aa:78:11
    MEP status: running
    Defects:
      Remote MEP not receiving CCM                  : no
      Erroneous CCM received                        : no
      Cross-connect CCM received                    : no
      RDI sent by some MEP                          : no
      Some remote MEP's MAC in error state          : no
    Statistics:
      CCMs sent                                     : 14666
      CCMs received out of sequence                 : 0
      LBMs sent                                     : 0
      Valid in-order LBRs received                  : 0
      Valid out-of-order LBRs received              : 0
      LBRs received with corrupted data             : 0
      LBRs sent                                     : 0
      LTMs sent                                     : 2
      LTMs received                                 : 0
      LTRs sent                                     : 0
      LTRs received                                 : 2
      Sequence number of next LTM request           : 2
      1DMs sent                                     : 0
      Valid 1DMs received                           : 0
      Invalid 1DMs received                         : 0
      Out of sync 1DMs received                     : 0
      DMMs sent                                     : 0
      Valid DMMs received                           : 0
      Invalid DMMs received                         : 0
      DMRs sent                                     : 0
      Valid DMRs received                           : 0
      Invalid DMRs received                         : 0
    Remote MEP count: 1
      Identifier    MAC address        State    Interface
        102     00:1f:12:b8:38:11       ok    ge-1/3/9.0

Linktrace to 00:1f:12:b8:38:11, Interface : ge-1/3/9.0
      Maintenance Domain: pbbn, Level: 5 
      Maintenance Association: vlan3350, Local Mep: 100
      Transaction Identifier: 2
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     62     00:1f:12:b8:38:11         00:00:00:00:00:00   

Interface name: cbp0.0, vlan 3350, Interface status: Active, Link status: Up
  Maintenance domain name: pbbn, Format: string, Level: 5
    Maintenance association name: vlan3350, Format: string
    Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
    Interface status TLV: none, Port status TLV: none
    MEP identifier: 102, Direction: up, MAC address: 00:1f:12:b8:38:11
    MEP status: running
    Defects:
      Remote MEP not receiving CCM                  : no
      Erroneous CCM received                        : no
      Cross-connect CCM received                    : no
      RDI sent by some MEP                          : no
      Some remote MEP's MAC in error state          : no
    Statistics:
      CCMs sent                                     : 7507
      CCMs received out of sequence                 : 0
      LBMs sent                                     : 0
      Valid in-order LBRs received                  : 0
      Valid out-of-order LBRs received              : 0
      LBRs received with corrupted data             : 0
      LBRs sent                                     : 0
      LTMs sent                                     : 0
      LTMs received                                 : 3
      LTRs sent                                     : 3
      LTRs received                                 : 0
      Sequence number of next LTM request           : 0
      1DMs sent                                     : 0
      Valid 1DMs received                           : 0
      Invalid 1DMs received                         : 0
      Out of sync 1DMs received                     : 0
      DMMs sent                                     : 0
      Valid DMMs received                           : 0
      Invalid DMMs received                         : 0
      DMRs sent                                     : 0
      Valid DMRs received                           : 0
      Invalid DMRs received                         : 0
    Remote MEP count: 1
      Identifier    MAC address        State    Interface
        100     00:21:59:aa:78:11       ok    ge-1/0/4.0

Linktrace to 00:21:59:aa:78:11, Interface : ge-1/0/4.0
      Maintenance Domain: pbbn, Level: 5 
      Maintenance Association: vlan3350, Local Mep: 102
      Transaction Identifier: 0
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     62     00:21:59:aa:78:11         00:00:00:00:00:00  

MIP information for instance pbbn-1 eline-bvlan-vlan-3150
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  ge-2/1/5.0          5
  ge-2/3/0.0          5
  ge-2/3/9.0          5
  ge-1/3/0.0          5
  ge-1/3/9.0          5

MIP information for instance pbbn-1 eline-bvlan-vlan-3150
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  ge-2/0/6.0          5
  ge-1/3/0.0          5
  ge-1/3/9.0          5
  ge-2/3/0.0          5
  ge-2/3/9.0          5

Interface name: ge-1/1/0.0, vlan 500, Interface status: Active, Link status: Up
  Maintenance domain name: es-domain, Format: string, Level: 3
    Maintenance association name: eline-1, Format: string
    Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
    Interface status TLV: none, Port status TLV: none
    MEP identifier: 1, Direction: up, MAC address: 00:21:59:01:e3:3a
    MEP status: running
    Defects:        
      Remote MEP not receiving CCM                  : no
      Erroneous CCM received                        : no
      Cross-connect CCM received                    : no
      RDI sent by some MEP                          : no
      Some remote MEP's MAC in error state          : no
    Statistics:     
      CCMs sent                                     : 29310
      CCMs received out of sequence                 : 0
      LBMs sent                                     : 0
      Valid in-order LBRs received                  : 0
      Valid out-of-order LBRs received              : 0
      LBRs received with corrupted data             : 0
      LBRs sent                                     : 0
      LTMs sent                                     : 3
      LTMs received                                 : 2
      LTRs sent                                     : 2
      LTRs received                                 : 9
      Sequence number of next LTM request           : 3
      1DMs sent                                     : 0
      Valid 1DMs received                           : 0
      Invalid 1DMs received                         : 0
      Out of sync 1DMs received                     : 0
      DMMs sent                                     : 0
      Valid DMMs received                           : 0
      Invalid DMMs received                         : 0
      DMRs sent                                     : 0
      Valid DMRs received                           : 0
      Invalid DMRs received                         : 0
    Remote MEP count: 1
      Identifier    MAC address        State    Interface
          2     00:1f:12:b8:72:98       ok    ge-2/0/0.1

Linktrace to 00:1f:12:b8:72:98, Interface : ge-2/0/0.1
      Maintenance Domain: es-domain, Level: 3 
      Maintenance Association: eline-1, Local Mep: 1
      Transaction Identifier: 1
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     60     00:1f:12:b8:72:98         00:00:00:00:00:00  
    2     61     00:1f:12:b8:3f:b0         00:1f:12:b8:3a:95  
    3     62     00:21:59:aa:7d:2a         00:21:59:aa:7f:b0  

Interface name: ge-1/0/3.5, vlan 500, Interface status: Active, Link status: Up
  Maintenance domain name: es-domain, Format: string, Level: 3
    Maintenance association name: eline-1, Format: string
    Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
    Interface status TLV: none, Port status TLV: none
    MEP identifier: 2, Direction: up, MAC address: 00:1f:12:b8:72:98
    MEP status: running
    Defects:        
      Remote MEP not receiving CCM                  : no
      Erroneous CCM received                        : no
      Cross-connect CCM received                    : no
      RDI sent by some MEP                          : no
      Some remote MEP's MAC in error state          : no
    Statistics:     
      CCMs sent                                     : 8133
      CCMs received out of sequence                 : 0
      LBMs sent                                     : 8
      Valid in-order LBRs received                  : 0
      Valid out-of-order LBRs received              : 0
      LBRs received with corrupted data             : 0
      LBRs sent                                     : 0
      LTMs sent                                     : 4
      LTMs received                                 : 0
      LTRs sent                                     : 0
      LTRs received                                 : 8
      Sequence number of next LTM request           : 4
      1DMs sent                                     : 0
      Valid 1DMs received                           : 0
      Invalid 1DMs received                         : 0
      Out of sync 1DMs received                     : 0
      DMMs sent                                     : 0
      Valid DMMs received                           : 0
      Invalid DMMs received                         : 0
      DMRs sent                                     : 0
      Valid DMRs received                           : 0
      Invalid DMRs received                         : 0
    Remote MEP count: 1
      Identifier    MAC address        State    Interface
          1     00:21:59:01:e3:3a       ok    ge-1/0/0.1 

Linktrace to 00:21:59:01:e3:3a, Interface : ge-1/0/0.1
      Maintenance Domain: es-domain, Level: 3 
      Maintenance Association: eline-1, Local Mep: 2
      Transaction Identifier: 4
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     62     00:1f:12:b8:3a:95         00:1f:12:b8:3f:b0  
    2     61     00:22:83:32:df:b0         00:22:83:32:da:95  

MIP information for instance pbn-1-for-eline eline-svlans-vlan-1200
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-2/0/0.2          3

MIP information for instance pbn-1-for-eline eline-svlans-vlan-2100
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-2/0/0.1          3

MIP information for instance pbn-1-for-eline eline-svlans-vlan-1200
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-1/0/0.2          3

MIP information for instance pbn-1-for-eline eline-svlans-vlan-2100
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-1/0/0.1          3

MIP information for instance pbn-3-for-eline eline-svlans-vlan-1200
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-1/0/0.2          3

MIP information for instance pbn-3-for-eline eline-svlans-vlan-2100
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-1/0/0.1          3

Interface name: ge-1/1/0.0, vlan 600, Interface status: Active, Link status: Up
  Maintenance domain name: es-domain, Format: string, Level: 3
    Maintenance association name: eline-2, Format: string
    Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
    Interface status TLV: none, Port status TLV: none
    MEP identifier: 1, Direction: up, MAC address: 00:21:59:01:e3:3a
    MEP status: running
    Defects:
      Remote MEP not receiving CCM                  : no
      Erroneous CCM received                        : no
      Cross-connect CCM received                    : no
      RDI sent by some MEP                          : no
      Some remote MEP's MAC in error state          : no
    Statistics:
      CCMs sent                                     : 29310
      CCMs received out of sequence                 : 0
      LBMs sent                                     : 19
      Valid in-order LBRs received                  : 1
      Valid out-of-order LBRs received              : 0
      LBRs received with corrupted data             : 0
      LBRs sent                                     : 0
      LTMs sent                                     : 2
      LTMs received                                 : 0
      LTRs sent                                     : 0
      LTRs received                                 : 6
      Sequence number of next LTM request           : 2
      1DMs sent                                     : 0
      Valid 1DMs received                           : 0
      Invalid 1DMs received                         : 0
      Out of sync 1DMs received                     : 0
      DMMs sent                                     : 0
      Valid DMMs received                           : 0
      Invalid DMMs received                         : 0
      DMRs sent                                     : 0
      Valid DMRs received                           : 0
      Invalid DMRs received                         : 0
    Remote MEP count: 1
      Identifier    MAC address        State    Interface
          2     00:1f:12:b8:72:98       ok    ge-2/0/0.2

Linktrace to 00:1f:12:b8:72:98, Interface : ge-2/0/0.2
      Maintenance Domain: es-domain, Level: 3 
      Maintenance Association: eline-2, Local Mep: 2
      Transaction Identifier: 1
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     60     00:1f:12:b8:72:98         00:00:00:00:00:00  
    2     61     00:1f:12:b8:3f:b0         00:1f:12:b8:3a:95  
    3     62     00:21:59:aa:7d:2a         00:21:59:aa:7f:b0  

Interface name: ge-1/0/3.6, vlan 600, Interface status: Active, Link status: Up
  Maintenance domain name: es-domain, Format: string, Level: 3
    Maintenance association name: eline-2, Format: string
    Continuity-check status: enabled, Interval: 1s, Loss-threshold: 3 frames
    Interface status TLV: none, Port status TLV: none
    MEP identifier: 2, Direction: up, MAC address: 00:1f:12:b8:72:98
    MEP status: running
    Defects:
      Remote MEP not receiving CCM                  : no
      Erroneous CCM received                        : no
      Cross-connect CCM received                    : no
      RDI sent by some MEP                          : no
      Some remote MEP's MAC in error state          : no
    Statistics:
      CCMs sent                                     : 8135
      CCMs received out of sequence                 : 0
      LBMs sent                                     : 0
      Valid in-order LBRs received                  : 0
      Valid out-of-order LBRs received              : 0
      LBRs received with corrupted data             : 0
      LBRs sent                                     : 0
      LTMs sent                                     : 1
      LTMs received                                 : 0
      LTRs sent                                     : 0
      LTRs received                                 : 2
      Sequence number of next LTM request           : 1
      1DMs sent                                     : 0
      Valid 1DMs received                           : 0
      Invalid 1DMs received                         : 0
      Out of sync 1DMs received                     : 0
      DMMs sent                                     : 0
      Valid DMMs received                           : 0
      Invalid DMMs received                         : 0
      DMRs sent                                     : 0
      Valid DMRs received                           : 0
      Invalid DMRs received                         : 0
    Remote MEP count: 1
      Identifier    MAC address        State    Interface
          1     00:21:59:01:e3:3a       ok    ge-1/0/0.2

Linktrace to 00:21:59:01:e3:3a, Interface : ge-1/0/0.2
      Maintenance Domain: es-domain, Level: 3 
      Maintenance Association: eline-2, Local Mep: 2
      Transaction Identifier: 1
    Hop   TTL    Source MAC address        Next-hop MAC address
    .
    1     62     00:1f:12:b8:3a:95         00:1f:12:b8:3f:b0  
    2     61     00:21:59:aa:7f:b0         00:21:59:aa:7d:2a 

MIP information for instance pbn-1-for-eline eline-svlans-vlan-1200
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-2/0/0.2          3

MIP information for instance pbn-1-for-eline eline-svlans-vlan-2100
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-2/0/0.1          3

MIP information for instance pbn-1-for-eline eline-svlans-vlan-1200
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-1/0/0.2          3

MIP information for instance pbn-1-for-eline eline-svlans-vlan-2100
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-1/0/0.1          3

MIP information for instance pbn-3-for-eline eline-svlans-vlan-1200
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-1/0/0.2          3

MIP information for instance pbn-3-for-eline eline-svlans-vlan-2100
  maintenance-domain mhf            : unspecified 
  maintenance-association mhf       : unspecified
  default maintenance-domain mhf    : default

  Interface       Level
  pip0.0              3
  ge-1/0/0.1          3