• Supported Platforms
• EX Series

• Related Topics
• Understanding Multicast VLAN Registration on EX Series Switches
• Example: Configuring IGMP Snooping on EX Series Switches
• Configuring IGMP Snooping (CLI Procedure)
• RFC 3171, IANA Guidelines for IPv4 Multicast Address Assignments at http://tools.ietf.org/html/rfc3171

IGMP Snooping on EX Series Switches Overview

Internet Group Management Protocol (IGMP) snooping regulates multicast traffic in a switched network. With IGMP snooping enabled, a LAN switch monitors the IGMP transmissions between a host (a network device) and a multicast router, keeping track of the multicast groups and associated member interfaces. The switch uses that information to make intelligent multicast-forwarding decisions and forward traffic to the intended destination interfaces. Juniper Networks EX Series Ethernet Switches support IGMPv1, IGMPv2, and IGMPv3.

For details on IGMPv1, IGMPv2, and IGMPv3, see the following standards:

• For IGMPv1, see RFC 1112, Host extensions for IP multicasting at http://www.faqs.org/rfcs/rfc1112.html.
• For IGMPv2, see RFC 2236, Internet Group Management Protocol, Version 2 at http://www.faqs.org/rfcs/rfc2236.html.
• For IGMPv3, see RFC 3376, Internet Group Management Protocol, Version 3 at http://www.faqs.org/rfcs/rfc3376.html.

How IGMP Snooping Works

An EX Series switch usually learns unicast media access control (MAC) addresses by checking the source address field of the frames it receives. However, a multicast MAC address can never be the source address for a packet. As a result, the switch floods multicast traffic on the VLAN, consuming significant amounts of bandwidth.

IGMP snooping regulates multicast traffic on a VLAN to avoid flooding. When IGMP snooping is enabled, the switch intercepts IGMP packets and uses the content of the packets to build a multicast cache table. The cache table is a database of multicast groups and their corresponding member ports. The cache table is then used to regulate multicast traffic on the VLAN.

When the switch receives multicast packets, it uses the cache table to selectively forward the packets only to the ports that are members of the destination multicast group. Figure 1 shows an example of IGMP traffic flow with IGMP snooping enabled.

How IGMP Snooping Works with Routed VLAN Interfaces

Switches send traffic to hosts that are part of the same broadcast domain, but routers are needed to route traffic from one broadcast domain to another. Switches use a routed VLAN interface (RVI) to perform these routing functions. IGMP snooping works with Layer 2 interfaces and RVIs to regulate multicast traffic in a switched network.

When a switch receives a multicast packet, the Packet Forwarding Engines in the switch perform an IP multicast lookup on the multicast packet to determine how to forward the packet to its local ports. From the results of the IP multicast lookup, each Packet Forwarding Engine extracts a list of Layer 3 interfaces (which can include VLAN interfaces) that have ports local to the Packet Forwarding Engine. If an RVI is part of this list, the switch provides a bridge multicast group ID for each RVI to the Packet Forwarding Engine.

A bridge multicast ID is assigned to direct Layer 3 interfaces and to RVIs. For VLANs that include multicast receivers, the bridge multicast ID includes a sub-next-hop ID. The sub-next-hop ID identifies the multicast Layer 2 interfaces in that VLAN that are interested in receiving the multicast stream. The switch ultimately assigns a next hop after it does a route lookup. The next hop includes all direct Layer 3 interfaces and RVIs. The Packet Forwarding Engine then forwards multicast traffic to the bridge multicast ID that includes all Layer 3 interfaces and RVIs that are multicast receivers for a given multicast group.

Figure 2 shows how multicast traffic is forwarded on a multilayer switch. In this illustration, multicast traffic is coming in through the xe-0/1/0.0 interface. A multicast group has been formed by the Layer 3 interface ge-0/0/2.0, vlan.0, and vlan.1. The ge-2/0/0.0 interface is a common trunk interface that belongs to both vlan.0 and vlan.1. The letter “R” next to an interface name in the illustration indicates that a multicast receiver host is associated with that interface.

Note: Traffic sent to an access interface is untagged; traffic sent to a trunk interface is tagged. For more information on VLAN tagging, see Understanding Bridging and VLANs on EX Series Switches.

Table 1 shows the bridge multicast IDs and next hops that are created. The term subnh refers to a sub-next hop. The Packet Forwarding Engine will forward multicast traffic to bridge multicast ID9.

How Hosts Join and Leave Multicast Groups

Hosts can join multicast groups in either of two ways:

• By sending an unsolicited IGMP join message to a multicast router that specifies the IP multicast group that the host is attempting to join.
• By sending an IGMP join message in response to a general query from a multicast router.

A multicast router continues to forward multicast traffic to a VLAN provided that at least one host on that VLAN responds to the periodic general IGMP queries. For a host to remain a member of a multicast group, therefore, it must continue to respond to the periodic general IGMP queries.

To leave a multicast group, a host can either not respond to the periodic general IGMP queries, which results in a “silent leave” (the only leave option for hosts connected to switches running IGMPv1), or send a group-specific IGMPv2 leave message.

Note: A host does not leave a group if its link goes down—for example, if a user disconnects from the port. The host remains a member of the group until group membership times out and a silent leave occurs. This means that if another user connects to the port before the silent leave occurs, the host resumes receiving the group multicast traffic until the silent leave, even though it never sent an IGMP join message.

IGMP Snooping Support for IGMPv3

IGMPv3 allows IGMP snooping to filter multicast streams based on the source address of the multicast stream. Junos operating system (Junos OS) for EX Series switches supports IGMPv3 packets that are in INCLUDE or EXCLUDE mode.

When a host sends an IGMPv3 INCLUDE report through a switch interface to indicate that it wants to receive a multicast stream from a source address, the switch adds the source address to the source list. In INCLUDE mode, the switch requests that packets be sent to the specified multicast address only from those IP source addresses listed in the source-list parameter. However, because EX Series switches do not support forwarding on a per-source basis, the switch merges all IGMPv3 reports for a VLAN to create a (*,G,V) route with the appropriate next hop. This next hop contains all the interfaces on the VLAN that are interested in group G.

When IGMP snooping for IGMPv3 is used with an RVI, the same (*,G,V) route is added to the snooping information in the RVI’s output interface list (olist).

When a host sends an IGMPv3 EXCLUDE report, the host indicates that it wants to join a multicast group and receive packets for that group except from those IP source addresses in the source-list parameter. However, because EX Series switches do not support forwarding on a per-source basis, the switch ignores the source information and creates a (*,G,V) route. A host can also send an EXCLUDE report in which the source-list parameter is empty, which is known as an EXCLUDE NULL report. An EXCLUDE NULL report indicates that the host wants to join the multicast group and receive packets from all sources. The switch creates a (*, G,V) route in this case also.