Unified ISSU Concepts

A unified in-service software upgrade (unified ISSU) enables you to upgrade between two different JUNOS software releases with no disruption on the control plane and with minimal disruption of traffic. Unified ISSU is only supported on dual Routing Engine platforms. In addition, the graceful Routing Engine switchover (GRES) and nonstop active routing (NSR) must be enabled.

A unified ISSU provides the following benefits:

• Eliminates network downtime during software image upgrades
• Reduces operating costs, while delivering higher service levels
• Allows fast implementation of new features

Note: The master Routing Engine and backup Routing Engine must be running the same software version before you can perform a unified ISSU. You cannot take any PICs online or offline during a unified ISSU.

To perform a unified ISSU, complete the following steps:

1. Enable Graceful Routing Engine switchover and nonstop active routing. Verify that the Routing Engines and protocols are synchronized.
2. Download the new software package from the Juniper Networks Support Web site and then copy the package to the router.
3. Issue the request system software in-service-upgrade command on the master Routing Engine.

A JUNOS release package comprises three distinct systems:

• Juniper Networks Operating System, which provides system control and all the features and functions of the Juniper Networks router that executes in the Routing Engines
• Juniper Networks Packet Forwarding Engine, which supports the high-performance traffic forwarding and packet handling capabilities
• Interface control

After the request system software in-service-upgrade command is issued, the following process occurs.

Note: In the illustrations, a solid line indicates the high-speed internal link between a Routing Engine and a Packet Forwarding Engine. A dotted line indicates the chassis process (chassisd), another method of communication between a Routing Engine and a Packet Forwarding Engine. RE0m and RE1s indicate master and backup (or standby) Routing Engines, respectively.

Note: The following process pertains to all supported routing platforms except the TX Matrix platform. For information about the unified ISSU process on the TX Matrix platform, see Unified ISSU Process on the TX Matrix Platform. On M320 and T320 routers and on T640 and T1600 routing nodes, the Packet Forwarding Engine resides on an FPC. However, on an M120 router, the Forwarding Engine Board (FEB) replaces the functions of a Packet Forwarding Engine. In the illustrations and steps, when considering an M120 router, you can regard the PFE as an FPC. As an additional step on an M120 router, after the FPCs and PICs have been upgraded, the FEBs are upgraded.

1. The master Routing Engine validates the router configuration to ensure that it can be committed using the new software version. Checks are made for unsupported configurations and for unsupported Physical Interface Cards (PICs). Unsupported PICs do not prevent a unified ISSU. The software issues a warning to indicate that these PICs will restart during the upgrade. Similarly, an unsupported protocol configuration does not prevent a unified ISSU. The software issues a warning that packet loss may occur for the protocol during the upgrade.

   

2. When the validation succeeds, the kernel state synchronization daemon (ksyncd) synchronizes the kernel on the backup Routing Engine with the master Routing Engine.
3. The backup Routing Engine is upgraded with the new software image. Before being upgraded, the backup Routing Engine gets the configuration file from the master Routing Engine and validates the configuration to ensure that it can be committed using the new software version. After being upgraded, it is resynchronized with the master Routing Engine. In the illustration, an apostrophe ( ' ) indicates the device is running the new version of software.

   

4. The chassis process (chassisd) on the master Routing Engine prepares other software processes for the unified ISSU. When all the processes are ready, chassisd sends an ISSU_PREPARE message to the Flexible PIC Concentrators (FPCs) installed in the router.
5. The Packet Forwarding Engine on each FPC saves its state and downloads the new software image from the backup Routing Engine. Next, each Packet Forwarding Engine sends an ISSU_READY message to the chassis process (chassisd).

   

6. After receiving an ISSU_READY message from a Packet Forwarding Engine, the chassis process (chassisd) sends an ISSU_REBOOT message to the FPC on which the Packet Forwarding Engine resides. The FPC reboots with the new software image. After the FPC is rebooted, the Packet Forwarding Engine restores the FPC state and a high-speed internal link is established with the backup Routing Engine running the new software. The chassis process (chassisd) is also re-established with the master Routing Engine.
7. After all Packet Forwarding Engines have sent a READY message via the chassis process (chassisd) on the master Routing Engine, other software processes are prepared for a Routing Engine switchover. The system is ready for a switchover at this point.

   

   Note: In the case of an M120 router, the FEBs are upgraded at this point. When all FEBs have been upgraded, the system is ready for a switchover.

8. The Routing Engine switchover occurs and the backup Routing Engine becomes the new master Routing Engine.

   

9. The new backup Routing Engine is now upgraded to the new software image. (This step is skipped if the no-old-master-upgrade option is specified.)

   

10. When the backup Routing Engine has been successfully upgraded, the unified ISSU is complete.

Copyright © 2009, Juniper Networks, Inc. All rights reserved. Trademark Notice.