[Contents] [Prev] [Next] [Index] [Report an Error]

Miscellaneous Commands for a Routing Matrix

There are a variety of other useful commands you can use when maintaining a routing matrix.

To display the location of routing matrix components and convert FPCs from T640 routing node local numbering to routing matrix global numbering, issue the show chassis location fpc command on the TX Matrix platform:
user@router> show chassis location fpc
```
Global FPC    LCC     Local FPC
     1          0         1
     2          0         2
     3          0         3
    16          2         0
    17          2         1
    19          2         3
```
To check the status of the SIB connection between the TX Matrix platform and T640 routing nodes, issue the show chassis fabric topology command on the TX Matrix platform. All values for each available T640 routing node (LCC) should be in the UP state. In the following excerpt of output for this command, a routing matrix that contains only LCCs 0 and 2 shows only these two T640 routing nodes as being UP:
```
LCC0_SIB-L0_F0,03->SIB-S0_F0,00 UP
LCC1_SIB-L0_F0,03->SIB-S0_F0,01 RESET
LCC2_SIB-L0_F0,03->SIB-S0_F0,02 UP
LCC3_SIB-L0_F0,03->SIB-S0_F0,03 RESET
```

To verify that the Ethernet links between the TX Matrix platform and the T640 routing node control boards are operational, issue the show chassis ethernet-switch command on the TX Matrix platform:
user@router> show chassis ethernet-switch

scc-re0:
--------------------------------------------------------------------------
Link is good on FE port 4 connected to device: LCC0
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on FE port 6 connected to device: LCC2
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on FE port 8 connected to device: SPMB
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on GE port 13 connected to device: Other RE
  Speed is 1000Mb
  Duplex is full
  Autonegotiate is Enabled
lcc0-re0:
--------------------------------------------------------------------------
Link is good on FE port 1 connected to device: FPC1
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on FE port 2 connected to device: FPC2
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on FE port 3 connected to device: FPC3
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on FE port 8 connected to device: SPMB
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on FE port 10 connected to device: SCC
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on GE port 13 connected to device: Other RE
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
lcc2-re0:
--------------------------------------------------------------------------
Link is good on FE port 0 connected to device: FPC0
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on FE port 1 connected to device: FPC1
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on FE port 3 connected to device: FPC3
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on FE port 8 connected to device: SPMB
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on FE port 10 connected to device: SCC
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled
Link is good on GE port 13 connected to device: Other RE
  Speed is 100Mb
  Duplex is full
  Autonegotiate is Enabled

Miscellaneous Commands for a Routing Matrix

Related Topics