Tag Elements Beginning with S > <serial-options> (configuration/interfaces/interface)

Usage

<configuration>
    <interfaces>
        <interface>
            <serial-options>
                <line-protocol>line-protocol-choice</line-protocol>
                <dte-options>...</dte-options>
                <dce-options>...</dce-options>
                <dtr-circuit>dtr-circuit-choice</dtr-circuit>
                <dtr-polarity>dtr-polarity-choice</dtr-polarity>
                <rts-polarity>rts-polarity-choice</rts-polarity>
                <control-polarity>control-polarity-choice</control-polarity>
                <dcd-polarity>dcd-polarity-choice</dcd-polarity>
                <dsr-polarity>dsr-polarity-choice</dsr-polarity>
                <cts-polarity>cts-polarity-choice</cts-polarity>
                <indication-polarity>indication-polarity-choice</indication-polarity>
                <tm-polarity>tm-polarity-choice</tm-polarity>
                <clocking-mode>clocking-mode-choice</clocking-mode>
                <transmit-clock>transmit-clock-choice</transmit-clock>
                <clock-rate>clock-rate-choice</clock-rate>
                <loopback>loopback-choice</loopback>
                <encoding>encoding-choice</encoding>
                <idle-cycle-flag>idle-cycle-flag-choice</idle-cycle-flag>
            </serial-options>
        </interface>
    </interfaces>
</configuration>

Description

Serial interface-specific options.

Contents

<clock-rate>—Interface clock rate.

• 1.0mhz—1.0 MHz.
• 1.2khz—1.2 KHz.
• 1.3mhz—1.3 MHz.
• 125.0khz—125.0 KHz.
• 148.0khz—148.0 KHz.
• 16.384mhz—16.384 MHz.
• 19.2khz—19.2 KHz.
• 2.048mhz—2.048 MHz.
• 2.0mhz—2.0 MHz.
• 2.341mhz—2.341 MHz.
• 2.4khz—2.4 KHz.
• 2.731mhz—2.731 MHz.
• 250.0khz—250.0 KHz.
• 3.277mhz—3.277 MHz.
• 38.4khz—38.4 KHz.
• 4.096mhz—4.096 MHz.
• 4.0mhz—4.0 MHz.
• 5.461mhz—5.461 MHz.
• 500.0khz—500.0 KHz.
• 56.0khz—56.0 KHz.
• 64.0khz—64.0 KHz.
• 72.0khz—72.0 KHz.
• 8.0mhz—8.0 MHz.
• 8.192mhz—8.192 MHz.
• 800.0khz—800.0 KHz.
• 9.6khz—9.6 KHz.

<clocking-mode>—Clock mode.

• dce—DCE timing (DTE mode only, not valid for X.21).
• internal—Internal baud timing.
• loop—Loop timing.

<control-polarity>—X.21 Control signal polarity.

• negative—Negative polarity.
• positive—Positive polarity.

<cts-polarity>—Clear To Send signal polarity.

• negative—Negative polarity.
• positive—Positive polarity.

<dcd-polarity>—Data Carrier Detect signal polarity.

• negative—Negative polarity.
• positive—Positive polarity.

<dce-options>—DCE options.

<dsr-polarity>—Data Set Ready signal polarity.

• negative—Negative polarity.
• positive—Positive polarity.

<dte-options>—DTE options/control leads.

<dtr-circuit>—Data Transmit Ready circuit mode.

• balanced—Balanced signal.
• unbalanced—Unbalanced signal.

<dtr-polarity>—Data Transmit Ready signal polarity.

• negative—Negative polarity.
• positive—Positive polarity.

<encoding>—Line encoding.

• nrz—Non-Return-To-Zero.
• nrzi—Non-Return-To-Zero-Invertible.

<idle-cycle-flag>—Value to transmit in idle cycles.

• flags—Transmit 0x7E in idle cycles.
• ones—Transmit 0xFF (all ones) in idle cycles.

<indication-polarity>—X.21 Indication signal polarity.

• negative—Negative polarity.
• positive—Positive polarity.

<line-protocol>—Line protocol to be used.

• eia530—Line protocol EIA530.
• v.35—Line protocol V.35.
• x.21—Line protocol X.21.

<loopback>—Loopback mode.

• dce-local—DCE local loopback (DTE mode only).
• dce-remote—DCE remote loopback.
• local—Local loopback.
• remote—Remote/LIU loopback.

<rts-polarity>—Request To Send signal polarity.

• negative—Negative polarity.
• positive—Positive polarity.

<tm-polarity>—Test Mode signal polarity.

• negative—Negative polarity.
• positive—Positive polarity.

<transmit-clock>—Transmit clock phase.

• invert—Shift clock phase 180 degrees.