[Contents] [Prev] [Next] [Index] [Report an Error]

Physical Interfaces Properties Statements List

Table 10 lists statements that you can use to configure physical interfaces.

Table 10: Statements for Physical Interface Properties

Statement	Interface Types	Usage Guidelines
`802.3ad aex`	Aggregated Ethernet interfaces	Configuring Ethernet Link Aggregation or Configuring Aggregated Ethernet Interfaces
`access-profile name`	Interfaces with Point-to-Point Protocol (PPP) encapsulation	Configuring the PPP Challenge Handshake Authentication Protocol
`accounting-profile name`	All	Configuring Accounting for the Physical Interface
`acfc`	Interfaces with PPP encapsulation	Identifying the Access Concentrator
`acknowledge-retries number`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`acknowledge-timer milliseconds`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`action-red-differential-delay (disable-tx \| remove-link)`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`advertise-interval milliseconds`	SONET/SDH interfaces	Configuring APS and MSP
`aggregate`	Gigabit Ethernet intelligent queuing (IQ) interfaces and Gigabit Ethernet interfaces with small form-factor pluggable transceivers (SFPs) (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i platform)	Configuring Gigabit Ethernet Policers
`aggregate asx`	Aggregated SONET/SDH interfaces	Configuring Aggregated SONET/SDH Interfaces
`aggregated-ether-options`	Aggregated Ethernet interfaces	Configuring Aggregated Ethernet Interfaces
`aggregate-ports`	SONET/SDH interfaces	Specifying OC768-over-OC192 Mode
`aggregated-sonet-options`	Aggregated SONET/SDH interfaces	Configuring Aggregated SONET/SDH Interfaces
`annex (annex-a \| annex-b)`	ATM interfaces on J-series Services Routers	Configuring SHDSL Operating Mode on an ATM Physical Interface
`aps`	SONET/SDH interfaces	Configuring APS and MSP
`atm-encapsulation (direct \| plcp)`	E3 and T3 traffic over Asynchronous Transfer Mode (ATM) interfaces	Configuring E3 and T3 Parameters on ATM Interfaces
`atm-options`	ATM1 and ATM2 IQ interfaces	Configuring ATM Interfaces
`authentication-key key`	SONET/SDH interfaces	Configuring APS and MSP
`backup-interface`	E1, E3, T1, T3 and Fast Ethernet	Configuring an ISDN Dialer Interface as a Backup Interface
`bandwidth-limit bps`	Gigabit Ethernet IQ and Gigabit Ethernet PICs with SFPs (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i platform)	Configuring Gigabit Ethernet Policers
`bchannel-allocation (ascending \| descending)`	J-series Services Routers equipped with a Dual-Port Channelized T1/E1 PIM; for Integrated Services Digital Network Primary Rate Interfaces (ISDN PRI)	Allocating B-Channels for Dialout
`bert-algorithm algorithm`	E3, T1, T3, multichannel DS3, channelized interfaces (DS3, OC12, and STM1), and channelized IQ and IQE interfaces (E1 and DS3)	Interface Diagnostics
`bert-error-rate rate`	E1, E3, T1, T3, and channelized interfaces (DS3, OC3, OC12, and STM1)	Interface Diagnostics
`bert-period seconds`	E1, E3, T1, T3, and channelized interfaces (DS3, OC12, and STM1)	Interface Diagnostics
`buildout value`	T1 interfaces	Configuring the T1 Buildout
`buildout feet`	E3 and T3 traffic over ATM interfaces	Configuring E3 and T3 Parameters on ATM Interfaces
`burst-size-limit bytes`	Gigabit Ethernet IQ and Gigabit Ethernet PICs with SFPs (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i platform)	Configuring Gigabit Ethernet Policers
`byte-encoding (nx56 \| nx64)`	DS0 and T1 interfaces	Configuring T1 Byte Encoding
`bytes [ values`	SONET/SDH interfaces	Configuring SONET/SDH Header Byte Values
`cbit-parity \| no-cbit-parity`	T3 interfaces	Disabling T3 C-Bit Parity Mode
`cbr rate`	ATM interfaces	Defining the ATM Traffic-Shaping Profile
`cell-bundle-size cells`	ATM2 IQ interfaces using ATM Layer 2 circuit cell-relay transport mode	Configuring the Layer 2 Circuit Cell-Relay Cell Maximum
`chap`	Interfaces with PPP encapsulation	Configuring the PPP Challenge Handshake Authentication Protocol
`cisco-interoperability send-lip-remove-link-for-link-reject`	link services IQ (lsq) interfaces	JUNOS Services Interfaces Configuration Guide
`classifier`	Gigabit Ethernet IQ interfaces	Specifying an Output Priority Map
`clocking clock-source`	ATM, DS0, E1, E3, SONET/SDH, T1, and T3 interfaces	Configuring the Clock Source
`clocking-mode (dce \| dte \| loop)`	Serial interfaces (EIA-530 and V.35)	Configuring the Serial Clocking Mode
`clock-rate rate`	Serial interfaces (EIA-530 and V.35)	Configuring the DTE Clock Rate
`compatibility-mode mode`	E3 and T3 interfaces	Configuring the E3 CSU Compatibility Mode and Configuring the T3 CSU Compatibility Mode
`compression`	Interfaces with PPP encapsulation	Configuring the PPP Protocol Field Compression
`control-polarity (negative \| positive)`	Serial interfaces (X.21)	Configuring Serial Signal Polarities
`control-signal (assert \| de-assert \| normal)`	Serial interfaces (X.21)	Configuring the Serial Signal Handling
`core-dump \| no-core-dump)`	Adaptive services, monitoring services, and collector interfaces	Configuring Multiservice Physical Interface Properties
`cts (ignore \| normal \| require)`	Serial interfaces (EIA-530 and V.35)	Configuring the Serial Signal Handling
`cts-polarity (negative \| positive)`	Serial interfaces (EIA-530 and V.35)	Configuring Serial Signal Polarities
`current margin`	ATM interfaces on J-series Services Routers	Configuring SHDSL Operating Mode on an ATM Physical Interface
`dcd (ignore \| normal \| require)`	Serial interfaces (EIA-530 and V.35)	Configuring the Serial Signal Handling
`dcd-polarity (negative \| positive)`	Serial interfaces (EIA-530 and V.35)	Configuring Serial Signal Polarities
`dce`	Interfaces with Frame Relay encapsulation	Configuring the Router as a DCE
`dce-options`	Serial interfaces (EIA-530, V.35, and X.21) on J-series Services Routers	Configuring the Serial Signal Handling
`default-chap-secret name`	Interfaces with Point-to-Point Protocol (PPP) encapsulation	Configuring a Default CHAP Secret
`description text`	All	Adding an Interface Description to the Configuration
`dialer-options`	ISDN interfaces	Configuring ISDN Physical Interface Properties
`disable`	All	Disabling a Physical Interface, Tracing Operations of an Individual Router Interface, and Tracing Operations of an Individual Router Interface
`dot1x`	802.1x Port-Based Network Access Control	Configuring IEEE 802.1x Port-Based Network Access Control
`down-count`	ATM interfaces	Configuring the ATM OAM F5 Loopback Cell Threshold
`drop-timeout milliseconds`	Multilink, link services, and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`ds0-options`	DS0 interfaces	Configuring Channelized Interfaces
`dsr (ignore \| normal \| require)`	Serial interfaces (EIA-530 and V.35)	Configuring the Serial Signal Handling
`dsr-polarity (negative \| positive)`	Serial interfaces (EIA-530 and V.35)	Configuring Serial Signal Polarities
`dte-options`	Serial interfaces (EIA-530, V.35, and X.21) on M-series and T-series routing platforms	Configuring the Serial Signal Handling
`dtr signal-handling-option`	Serial interfaces (EIA-530 and V.35)	Configuring the Serial Signal Handling
`dtr-circuit (balanced \| unbalanced)`	Serial interfaces (EIA-530 and V.35)	Configuring the Serial DTR Circuit
`dtr-polarity (negative \| positive)`	Serial interfaces (EIA-530 and V.35)	Configuring Serial Signal Polarities
`e1-options`	E1 interfaces	Configuring E1 Interfaces
`e3-options`	E3 interfaces	Configuring E3 Interfaces
`encapsulation type`	All interfaces, except loopback and multicast tunnel	Configuring Interface Encapsulation
`encoding (nrz \| nrzi)`	Serial interfaces (EIA-530, V.35, and X.21)	Configuring Serial Line Encoding
`epd-threshold cells`	ATM2 interfaces	Configuring ATM2 IQ VC Tunnel CoS Components
`es-options`	ES interfaces	JUNOS Services Interfaces Configuration Guide
`ethernet-policer-profile`	Gigabit Ethernet IQ and Gigabit Ethernet PICs with SFPs (except the 10-port Gigabit Ethernet PIC, and the built-in Gigabit Ethernet port on the M7i platform)	Configuring Gigabit Ethernet Policers
`ethernet-switch-profile`	Gigabit Ethernet IQ and Gigabit Ethernet PICs with SFPs (except the 10-port Gigabit Ethernet PIC, Aggregated Ethernet with Gigabit Ethernet IQ interfaces, and the built-in Gigabit Ethernet port on the M7i platform)	Configuring Gigabit Ethernet Policers, Configuring MAC Address Filtering, and Configuring the Management Ethernet Interface
`facility-override facility-name`	Adaptive services interfaces	JUNOS Services Interfaces Configuration Guide
`fastether-options`	Fast Ethernet interfaces	Configuring Ethernet Interfaces
`fcs (16 \| 32)`	E1/E3, SONET/SDH, and T1/T3 interfaces	Configuring the E1 Frame Checksum, Configuring the E3 Frame Checksum, Configuring the SONET/SDH Frame Checksum, Configuring the T1 Frame Checksum, and Configuring the T3 Frame Checksum
`feac-loop-respond \| no-feac-loop-respond)`	T3 interfaces	Configuring the T3 FEAC Response
`flow-control \| no-flow-control)`	Aggregated Ethernet, Fast Ethernet, and Gigabit Ethernet interfaces	Configuring Flow Control
`force`	SONET/SDH interfaces	Configuring APS and MSP
`forwarding-class class-name`	Gigabit Ethernet IQ and ATM2 interfaces	Configuring ATM2 IQ VC Tunnel CoS Components and Specifying an Output Priority Map
`fragment-threshold bytes`	Multilink, link services, and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`framing framing-type`	10-Gigabit Ethernet, SONET, E1, E3, and T1 interfaces	Configuring E3 and T3 Parameters on ATM Interfaces, Configuring E1 Framing, and Configuring T1 Framing, Configuring 10-Gigabit Ethernet Framing, and Configuring SONET Options for 10-Gigabit Ethernet Interfaces
`gigether-options`	Gigabit Ethernet and Tri-Rate Ethernet copper interfaces	Configuring Ethernet Interfaces
`(gratuitous-arp-reply \| no-gratuitous-arp-reply)`	Ethernet interfaces	Configuring Gratuitous ARP
`hello-timer milliseconds`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`high-plp-max-threshold`	ATM2 interfaces	Configuring Linear RED Profiles
`high-plp-threshold percent`	ATM2 interfaces	=Configuring ATM2 IQ VC Tunnel CoS Components
`hold-time milliseconds`	SONET/SDH interfaces	Configuring APS and MSP
`hold-time up milliseconds down milliseconds`	All interfaces, except aggregated SONET/SDH, generalized routing encapsulation (GRE) tunnel, and IP tunnel	Damping Interface Transitions and Configuring SONET/SDH Defect Triggers to Be Ignored
`host hostname`	Adaptive services interfaces	JUNOS Services Interfaces Configuration Guide
`ieee802.1p premium [values]`	Gigabit Ethernet IQ interfaces	Specifying an Input Priority Map
`idle-cycle-flag value`	E1, E3, T1, and T3 interfaces	Configuring the E1 Idle Cycle Flag, Configuring the E3 Idle Cycle Flag, Configuring the T1 Idle Cycle Flag, and Configuring the T3 Idle Cycle Flag
`ignore-all`	Serial interfaces (EIA-530, V.35, and X.21)	Configuring the Serial Signal Handling
`ilmi`	ATM interfaces	Configuring Communication with Directly Attached ATM Switches and Routers
`inactivity-timeout seconds`	Adaptive services interfaces	JUNOS Services Interfaces Configuration Guide
`indication (ignore \| normal \| require)`	Serial interfaces (X.21)	Configuring the Serial Signal Handling
`indication-polarity (negative \| positive)`	Serial interfaces (X.21)	Configuring Serial Signal Polarities
`ingress-rate-limit rate`	8-port, 12-port, and 48-port Fast Ethernet interfaces	Configuring the Ingress Rate Limit
`init-command-string initialization-command-string;`	For USB ports (umd0) on J4350 and J6350 Services Routers	Specifying a USB Modem Interface on J-series Routers
`input-priority-map`	Gigabit Ethernet IQ interfaces	Specifying an Input Priority Map
`interface-type type`	Channelized IQ interfaces, ISDN interfaces	Configuring Channelized Interfaces and Configuring ISDN Physical Interface Properties
`invert-data`	DS0, E1, E3, and T1 interfaces	Configuring E1 Data Inversion , Configuring E3 Data Inversion, and Configuring T1 Data Inversion
`isdn-options`	ISDN interfaces	Configuring ISDN Logical Interface Properties
`keepalives <down-count number <interval seconds> <up-count number>`	Aggregated SONET/SDH, DS0, E1, E3, SONET/SDH, T1, and T3 interfaces	Configuring Keepalives
`lacp mode`	Aggregated Ethernet interfaces	Configuring Aggregated Ethernet LACP
`line-encoding (ami \| b8zs)`	T1 interfaces	Configuring T1 Line Encoding
`line-protocol protocol`	Serial interfaces (EIA-530, V.35, and X.21)	Configuring the Serial Line Protocol
`line-rate line-rate`	ATM interfaces on J-series Services Routers	Configuring SHDSL Operating Mode on an ATM Physical Interface
`linear-red-profile profile-name`	ATM2 interfaces	Configuring ATM2 IQ VC Tunnel CoS Components
`linear-red-profiles profile-name`	ATM2 interfaces	Configuring ATM2 IQ VC Tunnel CoS Components
`link-layer-overhead percent`	AS PIC link services IQ interfaces (lsq)	JUNOS Services Interfaces Configuration Guide
`link-mode mode`	Management Ethernet (fxp0) and Fast Ethernet interfaces	Configuring the Link Characteristics
`link-speed speed`	Aggregated Ethernet and aggregated SONET/SDH interfaces	Configuring Aggregated Ethernet Link Speed and Configuring Aggregated SONET/SDH Link Speed
`lmi lmi-options`	Interfaces with Frame Relay encapsulation	Configuring Tunable Keepalives for Frame Relay LMI and JUNOS Services Interfaces Configuration Guide
`lmi-type (ansi \| itu)`	Link services interfaces and interfaces with Frame Relay encapsulation	Configuring Frame Relay Keepalives
`local-name name`	Interfaces with PPP encapsulation	Configuring the PPP Challenge Handshake Authentication Protocol
`lockout`	SONET/SDH interfaces	Configuring APS and MSP
`log-prefix prefix-number`	Adaptive services interfaces	JUNOS Services Interfaces Configuration Guide
`(long-buildout \| no-long-buildout)`	T3 interfaces	Configuring the T3 Line Buildout
`(loop-timing \| no-loop-timing)`	Channelized IQ interfaces	Configuring the Channelized T3 Loop Timing
`loopback mode`	DS0, E1, E3, T1, T3, Ethernet, SONET/SDH, ATM interfaces on J-series Services Routers, serial interfaces (EIA-530, V.35, and X.21), and 10-Gigabit Ethernet interfaces in WAN PHY mode	Configuring E1 Loopback Capability, Configuring E3 Loopback Capability, Configuring Ethernet Loopback Capability, Configuring Serial Loopback Capability, Configuring Channelized IQ and IQE SONET/SDH Loop Timing, Configuring T1 Loopback Capability, Configuring T3 Loopback Capability, Configuring SHDSL Operating Mode on an ATM Physical Interface, and Configuring SONET Options for 10-Gigabit Ethernet Interfaces
`(loopback \| no-loopback)`	Aggregated Ethernet, Fast Ethernet, and Gigabit Ethernet interfaces	Configuring Ethernet Loopback Capability
`loss-priority (high \| low)`	Gigabit Ethernet IQ interfaces	Specifying an Output Priority Map
`low-plp-max-threshold percent`	ATM2 interfaces	Configuring ATM2 IQ VC Tunnel CoS Components
`low-plp-threshold percent`	ATM2 interfaces	Configuring ATM2 IQ VC Tunnel CoS Components
`lsq-failure-options`	Link services IQ (lsq) interfaces	JUNOS Services Interfaces Configuration Guide
`mac mac-address`	Management Ethernet interface (fxp0)	Configuring the MAC Address on the Management Ethernet Interface
`(mac-learn-enable \| no-mac-learn-enable)`	Gigabit Ethernet IQ, Tri-Rate Ethernet copper, and Gigabit Ethernet PICs with SFPs (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i platform)	Configuring MAC Address Filtering
`maximum-vcs maximum-vcs`	ATM interfaces	Configuring the Maximum Number of ATM1 VCs on a VP
`minimum-links number`	Multilink, link services, and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`mlfr-uni-nni-bundle-options bundle-options`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`modem-options`	For USB ports (umd0) on J4350 and J6350 Services Routers	Specifying a USB Modem Interface on J-series Routers
`mpls`	10-Gigabit Ethernet interfaces in WAN PHY mode and ATM and SONET/SDH interfaces in passive monitoring mode	Removing MPLS Labels from Incoming Packets and Removing MPLS Labels from Incoming Packets and Configuring SONET Options for 10-Gigabit Ethernet Interfaces
`mrru bytes`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`mtu bytes`	All interfaces, except management Ethernet (fxp0), loopback, multilink, and multicast tunnel	Configuring the Media MTU
`multiservice-options`	Adaptive services, monitoring services, and collector interfaces	Configuring Multiservice Physical Interface Properties
`n391 number`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`n392 number`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`n393 number`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`neighbor address`	SONET/SDH interfaces	Configuring APS and MSP
`no-gratuitous-arp-request`	Ethernet interfaces	Configuring Gratuitous ARP
`no-keepalives`	Interfaces with PPP, Frame Relay, or Cisco High-level Data Link Control (HDLC) encapsulation	Configuring Keepalives
`no-partition`	Channelized IQ interfaces	Configuring Channelized Interfaces
`no-termination-request`	link services IQ (lsq) interfaces	JUNOS Services Interfaces Configuration Guide
`oam-liveness`	ATM interfaces	Configuring the OAM F4 Cell Flows
`oam-period (seconds \| disable)`	ATM interfaces	Defining the ATM OAM F5 Loopback Cell Period
`oc-slice oc-slice-range`	Channelized OC12 IQ interfaces	Configuring Channelized OC12 Interfaces
`open-timeout seconds`	Adaptive services interfaces	JUNOS Services Interfaces Configuration Guide
`optics-options`	Gigabit Ethernet dense wavelength-division multiplexing (DWDM) interfaces	Configuring the 10-Gigabit Ethernet DWDM Interface Wavelength
`output-priority-map`	Gigabit Ethernet IQ interfaces	Specifying an Output Priority Map
`overflow (discard \| tag)`	All interfaces, except ATM, channelized E1, E1, Fast Ethernet, Gigabit Ethernet, and channelized IQ	Configuring Receive and Transmit Leaky Bucket Properties and Configuring Receive and Transmit Leaky Bucket Properties
`paired-group group-name`	SONET/SDH interfaces	Configuring APS and MSP
`partition partition-number`	Channelized IQ interfaces	Configuring Channelized Interfaces
`passive`	Interfaces with PPP encapsulation	Configuring the PPP Challenge Handshake Authentication Protocol
`passive-monitor-mode`	SONET/SDH interfaces	Enabling Passive Monitoring on SONET/SDH Interfaces
`path-trace trace-string`	10-Gigabit Ethernet interfaces in WAN PHY mode and SONET/SDH interfaces	Configuring the SONET/SDH Path Trace Identifier and Configuring SONET Options for 10-Gigabit Ethernet Interfaces
`(payload-scrambler \| no-payload-scrambler)`	E3, SONET/SDH, and T3 interfaces	Configuring E3 and T3 Parameters on ATM Interfaces, Configuring E3 HDLC Payload Scrambling, Configuring SONET/SDH HDLC Payload Scrambling, Configuring T3 HDLC Payload Scrambling, and Examples: Configuring T3 Interfaces
`periodic interval`	Aggregated Ethernet interfaces	Configuring Aggregated Ethernet LACP
`per-unit-scheduler`	IQ interfaces	JUNOS Services Interfaces Configuration Guide
`pfc`	Interfaces with PPP encapsulation	Configuring the PPP Protocol Field Compression
`pic-type (atm1 \| atm2)`	ATM2 IQ interfaces	Configuring the ATM PIC Type
`plp1 cells`	ATM2 interfaces	Configuring ATM2 IQ VC Tunnel CoS Components
`plp-to-clp`	ATM2 IQ interfaces	Enabling the PLP Setting to Be Copied to the CLP Bit
`policer cos-policer-name`	Gigabit Ethernet IQ and Gigabit Ethernet PICs with SFPs (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i platform)	Configuring Gigabit Ethernet Policers
`pop-all-labels`	ATM and SONET/SDH interfaces in passive monitoring mode	Removing MPLS Labels from Incoming Packets and Removing MPLS Labels from Incoming Packets
`ppp-options`	Interfaces with PPP encapsulation	Configuring the PPP Challenge Handshake Authentication Protocol
`premium`	Gigabit Ethernet IQ interfaces	Configuring Gigabit Ethernet Policers and Specifying an Output Priority Map
`primary sp-fpcpicport`	Redundant interfaces for adaptive services interfaces (rsp-)	JUNOS Services Interfaces Configuration Guide
`priority (high \| low)`	ATM2 IQ interfaces	Configuring ATM2 IQ VC Tunnel CoS Components
`priority number`	ISDN interfaces	Configuring an ISDN Dialer Interface as a Backup Interface
`promiscuous-mode`	ATM2 IQ interfaces	Configuring ATM Cell-Relay Promiscuous Mode
`protect-circuit group-name`	SONET/SDH interfaces	Configuring APS and MSP
`queue-depth cells`	ATM2 interfaces	Configuring ATM2 IQ VC Tunnel CoS Components
`queue-length number`	ATM1 interfaces	Configuring the ATM1 Queue Length
`rate percentage`	All interfaces, except ATM, channelized E1, E1, Fast Ethernet, Gigabit Ethernet, and channelized IQ	Configuring Receive and Transmit Leaky Bucket Properties and Configuring Receive and Transmit Leaky Bucket Properties
`receive-bucket`	All interfaces, except ATM, Fast Ethernet, and Gigabit Ethernet	Configuring Receive and Transmit Leaky Bucket Properties
`red-differential-delay milliseconds`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`redundancy-options`	Redundant interfaces for adaptive services interfaces (rsp-)	JUNOS Services Interfaces Configuration Guide
`remote-loopback-respond`	T1 interfaces	Configuring the T1 Remote Loopback Response
`request`	SONET/SDH interfaces	Configuring APS and MSP
`required-depth number`	ATM and SONET/SDH interfaces in passive monitoring mode	Removing MPLS Labels from Incoming Packets and Removing MPLS Labels from Incoming Packets
`revert-time seconds`	SONET/SDH interfaces	Configuring APS and MSP
`rfc-2615`	SONET/SDH interfaces	Configuring SONET/SDH RFC 2615 Support
`rts (assert \| de-assert \| normal)`	Serial interfaces (EIA-530 and V.35)	Configuring the Serial Signal Handling
`rts-polarity (negative \| positive)`	Serial interfaces (EIA-530 and V.35)	Configuring Serial Signal Polarities
`rtvbr peak rate sustained rate burst length`	ATM interfaces	Configuring ATM2 IQ Real-Time VBR
`scheduler-maps map-name`	ATM2 interfaces	Configuring ATM2 IQ VC Tunnel CoS Components
`schedulers number`	Ethernet IQ2 PIC port interfaces	JUNOS Services Interfaces Configuration Guide
`secondary sp-fpcpicport`	Redundant interfaces for adaptive services interfaces (rsp-)	JUNOS Services Interfaces Configuration Guide
`services-options`	Services interfaces	JUNOS Services Interfaces Configuration Guide
`serial-options`	Serial interfaces (EIA-530, V.35, and X.21)	Configuring Serial Interfaces
`services priority-level`	Adaptive services interfaces	JUNOS Services Interfaces Configuration Guide
`shdsl-options`	ATM interfaces on J-series Services Routers	Configuring SHDSL Operating Mode on an ATM Physical Interface
`size`	All	Tracing Operations of the Interface Process
`shaping`	ATM interfaces	Defining the ATM Traffic-Shaping Profile
`snext margin`	ATM interfaces on J-series Services Routers	Configuring SHDSL Operating Mode on an ATM Physical Interface
`snr-margin`	ATM interfaces on J-series Services Routers	Configuring SHDSL Operating Mode on an ATM Physical Interface
`sonet-options`	SONET/SDH interfaces	Configuring SONET/SDH Physical Interface Properties
`source-address-filter mac-address`	Aggregated Ethernet, Fast Ethernet, Tri-Rate Ethernet copper, and Gigabit Ethernet interfaces	Enabling Ethernet MAC Address Filtering
`(source-filtering \| no-source-filtering)`	Aggregated Ethernet, Fast Ethernet, Tri-Rate Ethernet copper, Gigabit Ethernet, Gigabit Ethernet IQ, and Gigabit Ethernet interfaces with SFPs (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i platform)	Enabling Ethernet MAC Address Filtering
`speed (10m \| 100m \| 1g \| oc3 \| oc12 \| oc48)`	Management Ethernet interface (fxp0), Tri-Rate Ethernet copper interfaces, and 12-port and 48-port Fast Ethernet interfaces SONET/SDH PIC with SFP	Configuring the Interface Speed and SONET/SDH Interface
`spid1spid2`	ISDN interfaces	Configuring ISDN Physical Interface Properties and Configuring an ISDN Dialer Interface as a Backup Interface
`stacked-vlan-tagging`	Gigabit Ethernet IQ interfaces	Configuring the Management Ethernet Interface
`start-end-flag (filler \| shared)`	DS0, E1, E3, T1, and T3 interfaces	Configuring E1 Start and End Flags, Configuring the E3 Start and End Flags, Configuring T1 Start and End Flags, and Configuring T3 Start and End Flags
`switching-mode (bidirectional \| unidirectional)`	Unchannelized OC3, OC12, and OC48 SONET/SDH interfaces on T-series platforms	Configuring Switching Between the Working and Protect Circuits
`syslog`	Adaptive services interfaces	JUNOS Services Interfaces Configuration Guide
`(syslog \| no-syslog)`	Adaptive services, monitoring services, and collector interfaces	Configuring Multiservice Physical Interface Properties
`t1-options`	T1 interfaces	Configuring T1 Interfaces
`t3-options`	T3 interfaces	Configuring T3 Interfaces
`t310`	ISDN interfaces	Configuring ISDN Physical Interface Properties
`t391 seconds`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`t392 number`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`tag-protocol-id (first-call \| power-up)`	ISDN interfaces	Configuring ISDN Physical Interface Properties
`threshold bytes`	All interfaces, except ATM, channelized E1, E1, Fast Ethernet, Gigabit Ethernet, and channelized IQ	Configuring Receive and Transmit Leaky Bucket Properties and Configuring Receive and Transmit Leaky Bucket Properties
`timeslots time-slot-range`	Channelized T1 IQ and channelized E1 IQ interfaces	Configuring Channelized Interfaces
`tm (ignore \| normal \| require)`	Serial interfaces (EIA-530)	Configuring the Serial Signal Handling
`tm-polarity (negative \| positive)`	Serial interfaces (EIA-530)	Configuring Serial Signal Polarities
`traceoptions`	All	Tracing Operations of an Individual Router Interface and Tracing Operations of the Interface Process
`transmit-bucket`	All interfaces, except ATM, Fast Ethernet, Tri-Rate Ethernet copper, and Gigabit Ethernet	Configuring Receive and Transmit Leaky Bucket Properties
`transmit-clock invert`	Serial interfaces (EIA-530, V.35, and X.21)	Configuring the Serial Clocking Mode
`transmit-weight (cells number \| percent number)`	ATM2 IQ interfaces	Configuring ATM2 IQ VC Tunnel CoS Components
`(traps \| no-traps)`	All	Enabling or Disabling SNMP Notifications on Physical Interfaces
`trigger defect ignore \| defect hold-time up milliseconds down milliseconds;`	10-Gigabit Ethernet interfaces in WAN PHY mode and ATM over SONET/SDH and SONET/SDH interfaces	Configuring SONET/SDH Defect Triggers to Be Ignored and Configuring SONET Options for 10-Gigabit Ethernet Interfaces
`(unframed \| no-unframed)`	E3 IQ interfaces	Configuring E3 IQ and IQE Unframed Mode
`unidirectional`	10-Gigabit Ethernet interfaces on MX960 4x10 GE DPC	Enabling Unidirectional Traffic Flow on Physical Interfaces
`vbr peak rate sustained rate burst length`	ATM interfaces	Defining the ATM Traffic-Shaping Profile
`vc-cos-mode (alternate \| strict)`	ATM2 interfaces	Configuring ATM2 IQ VC Tunnel CoS Components
`vlan-tagging`	Fast Ethernet, Tri-Rate Ethernet copper, and Gigabit Ethernet interfaces	Configuring 802.1Q VLANs
`vlan-vci-tagging`	Fast Ethernet, Tri-Rate Ethernet copper, Gigabit Ethernet, 10-Gigabit Ethernet, and aggregated Ethernet interfaces	Configuring ATM-to-Ethernet Interworking
`vpi vpi-identifier`	ATM interfaces	Configuring ATM Cell-Relay Promiscuous Mode and Configuring the Maximum Number of ATM1 VCs on a VP
`vtmapping`	Channelized STM1 interfaces	Configuring Virtual Tributary Mapping of Channelized STM1 Interfaces
`wavelength nm`	Gigabit Ethernet dense wavelength-division multiplexing (DWDM) interfaces	Configuring the 10-Gigabit Ethernet DWDM Interface Wavelength
`working-circuit group-name`	SONET/SDH interfaces	Configuring APS and MSP
`yellow-differential-delay milliseconds`	Link services and voice services interfaces	JUNOS Services Interfaces Configuration Guide
`(z0-increment \| no-z0-increment)`	SONET/SDH interfaces	Configuring an Incrementing STM ID

[Contents] [Prev] [Next] [Index] [Report an Error]