show rsvp neighbor

RSVP neighbor

Number of neighbors about which the router has learned. Each neighbor has one line of output.

All levels

via

Name of the interface where the neighbor has been detected. In the case of generalized MPLS (GMPLS) LSPs, the name of the peer where the neighbor has been detected.

detail

Address

Address of a learned neighbor.

All levels

Idle

Length of time the neighbor has been idle, in seconds.

All levels

Up/Dn

Number of neighbor up or down transitions detected by RSVP hello packets. If the up count is 1 greater than the down count, the neighbor is currently up. Otherwise, the neighbor is down. Neighbors that do not support RSVP hello packets, such as routers running JUNOS software Release 3.2 or earlier, are not reported as up or down.

All levels

Up cnt and Down cnt

Number of neighbor up or down transitions detected by RSVP hello packets. If the up count is 1 greater than the down count, the neighbor is currently up. Otherwise, the neighbor is down. Neighbors that do not support RSVP hello packets, such as routers running JUNOS software Release 3.2 or earlier, are not reported as up or down.

detail

status

State of the RSVP neighbor:

• Up—Router can detect RSVP Hello messages from the neighbor.
• Down—Router has received one of the following indications:
  • Communication failure from the neighbor.
  • Communication from IGP that the neighbor is unavailable.
  • Change in the sequence numbers in the RSVP Hello messages sent by the neighbor.

• Restarting—RSVP neighbor is unavailable and might be restarting. The neighbor remains in this state until it has restarted or is declared dead. This state is possible only when graceful restart is enabled.
• Restarted—RSVP neighbor has restarted and is undergoing state recovery (graceful restart) procedures.
• Dead—Router has lost all communication with the RSVP neighbor. Any RSVP sessions with that neighbor are torn down.

detail

LastChange

Time elapsed since the neighbor state changed either from up to down or from down to up. The format is hh:mm:ss.

All levels

Last changed time

Time elapsed since the neighbor state changed either from up to down or from down to up.

detail

HelloInt

Frequency at which RSVP hellos are sent on this interface (in seconds).

All levels

HelloTx/Rx

Number of hello packets sent to and received from the neighbor.

All levels

Hello

Number of RSVP hello packets that have been sent to and received from the neighbor.

detail

Message received

Number of Path and Resv messages that this router has received from the neighbor.

detail

Remote Instance

Identification provided by the remote router during Hello message exchange.

detail

Local Instance

Identification sent to the remote router during Hello message exchange.

detail

Refresh reduction

Measure of processing overhead requests of refresh messages. Refresh reduction extensions improve router performance by reducing the process overhead, thus increasing the number of LSPs a router can support. Refresh reduction can have the following values:

• operational—All four RSVP refresh reduction extensions—message ack, bundling, summary refresh, and staged refresh timer—are functional between the two neighboring routers. For a detailed explanation of these extensions, see RFC 2961.
• incomplete—Some RSVP refresh reduction extensions are functional between the two neighboring routers.
• no operational—Either the refresh reduction feature has been turned off, or the remote router cannot support the refresh reduction extensions.

detail

Remote end

Neighboring router's status in regard to refresh reduction:

• enabled—Remote router has requested refresh reduction during RSVP message exchanges.
• disabled—Remote router does not require refresh reduction.

detail

Ack-extension

An RSVP refresh reduction extension:

• enabled—Both local and remote routers support the ack-extension (RFC 2961).
• disabled—Remote router does not support the ack-extension.

detail

Link protection

Status of the MPLS fast reroute mechanism that protects traffic from link failure:

• enabled—Link protection feature has been turned on, protecting the neighbor with a bypass LSP.
• disabled—No link protection feature has been enabled for this neighbor.

detail

LSP name

Name of the bypass LSP.

detail

Bypass LSP

Status of the bypass LSP. It can have the following values:

• does not exist—Bypass LSP is not available.
• connecting—Router is in the process of establishing a bypass LSP, and the LSP is not available for link protection at the moment.
• operational—Bypass LSP is up and running.
• down—Bypass LSP has gone down, with the most probable cause a node or a link failure on the bypass path.

detail

Backup routes

Number of user LSPs (or routes) that are being protected by a bypass LSP (before link failure).

detail

Backup LSPs

Number of LSPs that have been temporarily established to maintain traffic by refreshing the downstream LSPs during link failure (not a one-to-one correspondence).

detail

Bypass explicit route

Explicit Route Object's (ERO) path that is taken by the bypass LSP.

detail

Restart time

Length of time a neighbor waits to receive a Hello from the restarting node before declaring the node dead and deleting the states (in milliseconds).

detail

Recovery time

Length of time during which the restarting node attempts to recover its lost states with help from its neighbors (in milliseconds). Recovery time is advertised by the restarting node to its neighbors, and applies to nodal faults. The restarting node considers its graceful restart complete after this time has elapsed.

detail