<mpls-lsp>

Usage

<rsvp-session | mpls-call-admission-control>
    <mpls-lsp>
        <destination-address>destination-address</destination-address>
        <source-address>source-address</source-address>
        <lsp-state>lsp-state</lsp-state>
        <route-count>route-count</route-count>
        <active-path>active-path</active-path>
        <is-primary/>
        <name>name</name>
        <bidirectional/>
        <lsp-description>lsp-description</lsp-description>
        <lsp-pktbytes>lsp-pktbytes</lsp-pktbytes>
        <no-statistics/>
        <mpls-p2mp-name>mpls-p2mp-name</mpls-p2mp-name>
        <is-fastreroute/>
        <is-linkprotection/>
        <is-nodeprotection/>
        <requires-intra-domain-path/>
        <load-balance>load-balance</load-balance>
        <lsp-diffserv-te-info>lsp-diffserv-te-info</lsp-diffserv-te-info>
        <metric>metric</metric>
        <revert-timer>revert-timer</revert-timer>
        <revert-timer-remain>revert-timer-remain</revert-timer-remain>
        <optimize-protection-timer>optimize-protection-timer
                                    </optimize-protection-timer>
        <admin-groups>...</admin-groups>
        <lsp-creation-time>lsp-creation-time</lsp-creation-time>
        <lsp-soft-preemption-counter>lsp-soft-preemption-counter
                                    </lsp-soft-preemption-counter>
        <lsp-soft-preemption-time>lsp-soft-preemption-time</lsp-soft-preemption-time>
        <retry-timer>retry-timer</retry-timer>
        <retry-limit>retry-limit</retry-limit>
        <mpls-lsp-autobandwidth>...</mpls-lsp-autobandwidth>
        <mpls-lsp-path>...</mpls-lsp-path>
        <mpls-lsp-attributes>...</mpls-lsp-attributes>
    </mpls-lsp>
</rsvp-session | mpls-call-admission-control>

Description

MPLS label-switched path information.

Contents

<active-path>—Path that the LSP is currently using.

<admin-groups>—No documentation is available yet.

<bidirectional>—LSP is bidirectional.

<destination-address>—Session destination address.

<is-fastreroute>—Detours will be established for an LSP so that if a node or link in the LSP fails, the traffic on the LSP can be rerouted with minimal packet loss.

<is-linkprotection>—Protect links via bypass LSPs.

<is-nodeprotection>—Protect link/node via bypass LSPs.

<is-primary>—Path is a primary path.

<load-balance>—Load-balancing algorithm chosen.

<lsp-creation-time>—Time when the LSP was created.

<lsp-description>—LSP description string (up to 80 characters).

<lsp-diffserv-te-info>—LSP support of DiffServ-TE extensions.

<lsp-pktbytes>—No documentation is available yet.

<lsp-soft-preemption-counter>—Number of times the LSP was soft preempted.

<lsp-soft-preemption-time>—Time when the LSP was last soft preempted.

<lsp-state>—State of an LSP.

<metric>—No documentation is available yet.

<mpls-lsp-attributes>—No documentation is available yet.

<mpls-lsp-autobandwidth>—No documentation is available yet.

<mpls-lsp-path>—Primary or secondary LSP path.

<mpls-p2mp-name>—No documentation is available yet.

<name>—No documentation is available yet.

<no-statistics>—No statistics are available for this session.

<optimize-protection-timer>—Optimize interval for fast-reroute detours, or link-protection bypasses.

<requires-intra-domain-path>—LSP path should be within the TE domain.

<retry-limit>—Maximum number of times the ingress tries to establish the primary path. It is reset each time primary path is created successfully.

<retry-timer>—Amount of time the ingress router waits between attempts to establish primary path.

<revert-timer>—Hold-down time before reverting to primary path.

<revert-timer-remain>—Time remaining before reverting:.

<route-count>—Number of active routes.

<source-address>—No documentation is available yet.