[Contents] [Prev] [Next] [Index] [Report an Error]

J-Web Configuration

To configure addresses, to configure a policy from the internal zone to the external zone, and to configure a policy to allow traffic between the internal zone and the gatekeeper in the external zone using the J-Web configuration editor, follow the sequence of steps listed below:

To configure addresses:

  1. Select Configuration > View and Edit > Edit Configuration.

    The Configuration page appears.

  2. Next to Security, click Configure or Edit.
  3. Next to Zones, click Configure or Edit.
  4. Next to Security zone, click Add new entry.
  5. In the Name box, type external.
  6. Next to Address book, click Configure or Edit.
  7. Next to Address, click Add new entry.
  8. In the Address name box, type ip_phone 2.2.2.5/32 and click OK.
  9. To configure another security zone internal, repeat Step 2 through Step 4 and click OK.
  10. Next to Address book, click Configure.
  11. Next to Address, click Add new entry.
  12. In the Address name box, type gatekeeper 2.2.2.10/32 and click OK.

To configure a policy from the internal zone to the external zone:

  1. Select Configuration > View and Edit > Edit Configuration.

    The Configuration page appears.

  2. Next to Security, click Configure or Edit.
  3. Next to Policies, select the check box and click Configure or Edit.
  4. Next to Policy, click Add new entry.
  5. In the From zone name box, type internal.
  6. In the To zone name box, type external and click OK.
  7. Under the From zone name column, click internal.
  8. Next to Policy, click Add new entry.
  9. In the Name box, type p_1.
  10. Select the Match check box.
  11. Select the Then check box.
  12. Next to Match, click Configure or Edit.
  13. Next to Source address, select Enter Source address and click Add new entry.
  14. From the Value keyword list, select any and click OK.
  15. Next to Destination address, click Add new entry.
  16. From the Value keyword list, select Enter Specific Value.
  17. In the Address box, type ip_phone and click OK.
  18. Next to Application, click Add new entry.
  19. In the Value keyword box, type junos-h323 and click OK.
  20. Next to Then, click Configure.
  21. Next to Action, enter permit and click OK.

To configure a policy to allow traffic between the internal zone and the gatekeeper in the external zone:

  1. Select Configuration > View and Edit > Edit Configuration.

    The Configuration page appears.

  2. Next to Security, click Configure or Edit.
  3. Next to Policies, select the check box and click Configure or Edit.
  4. Next to Policy, click Add new entry.
  5. In the From zone name box, type internal.
  6. In the To zone name box, type external and click OK.
  7. Next to Policy, click Add new entry.
  8. In the Policy name box, type p_2.
  9. Select the Match check box.
  10. Select the Then check box.
  11. Next to Match, click Configure.
  12. Next to Source address, select Enter Source address and click Add new entry.
  13. From the Value keyword list, select any and click OK.
  14. Next to Destination address, click Add new entry.
  15. From the Value keyword list, select Enter Specific Value.
  16. Next to Address box, type gatekeeper and click OK.
  17. Next to Application, click Add new entry.
  18. In the Value keyword box, type junos-h323 and click OK
  19. Next to Then, click Configure.
  20. Next to Action, enter permit and click OK.

To configure a policy to allow traffic between phones in the internal zone and the external zone:

  1. Select Configuration > View and Edit > Edit Configuration.

    The Configuration page appears.

  2. Next to Security, click Configure or Edit.
  3. Next to Policies, select the check box and click Configure or Edit.
  4. Next to Policy, Add new entry.
  5. In the From zone name box, type external.
  6. In the To zone name box, type internal and click OK.
  7. Under the From zone name column, click external.
  8. Next to Policy, click Add new entry.
  9. In the Policy name box, type p_3.
  10. Select the Match check box.
  11. Select the Then check box.
  12. Next to Match, click Configure.
  13. Next to Source address, select Enter Source address and click Add new entry.
  14. From the Value keyword list, select ip_phone and click OK.
  15. Next to Destination address, click Add new entry.
  16. From the Value keyword list, select Enter Specific Value.
  17. In the Address box, type any and click OK.
  18. Next to Application, click Add new entry.
  19. In the Value keyword box, type junos-h323 and click OK
  20. Next to Then, click Configure.
  21. Next to Action, enter permit and click OK.

To configure a policy to allow traffic between phones in the internal zone and the gatekeeper in the external zone:

  1. Select Configuration > View and Edit > Edit Configuration.

    The Configuration page appears.

  2. Next to Security, click Configure or Edit.
  3. Select the Policies check box, and click Configure or Edit.
  4. Next to Policy, Add new entry.
  5. In the From zone name box, type external.
  6. In the To zone name box, type internal and click OK.
  7. Next to Policy, click Add new entry.
  8. Under the From zone name column, click external.
  9. In the Policy name box, type p_4.
  10. Select the Match check box.
  11. Select the Then check box.
  12. Next to Match, click Configure.
  13. Next to Source address, select Enter Source address and click Add new entry.
  14. From the Value keyword list, select gatekeeper and click OK.
  15. Next to Destination address, click Add new entry.
  16. From the Value keyword list, select Enter Specific Value.
  17. In the Address box, type any and click OK.
  18. Next to Application, click Add new entry.
  19. In the Value keyword box, type junos-h323 and click OK
  20. Next to Then, click Configure.
  21. Next to Action, enter permit and click OK.
  22. If you are finished configuring the J-series device, commit the configuration.
[Contents] [Prev] [Next] [Index] [Report an Error]

Copyright © 2008, Juniper Networks, Inc. All rights reserved. Trademark Notice.