Step 2: Verify That the Interface Is Up
Purpose
Display the status of a Channelized OC-12 or Channelized OC-12 IQ interface to determine whether the physical link is up or down.
Action
To verify that the status of the Channelized OC-12 or Channelized OC-12 IQ interface is up, use the following JUNOS command-line interface (CLI) operational mode command:
user@host> show interfaces t3-fpc/pic/port:channel extensive.
 |
NOTE: For a list of interface types associated with the Channelized OC-12 IQ interface, see Channelized Intelligent Queuing Interface Naming. |
Sample Output
user@host> show interfaces t3-0/3/0:0 extensive
Physical interface: t3-0/3/0:0, Enabled, Physical link is Up
Interface index: 193, SNMP ifIndex: 118, Generation: 122
Link-level type: PPP, MTU: 4474, Clocking: Internal, SONET mode, Speed: T3,
Loopback: Local, SONET Loopback: None, FCS: 16, Mode: C/Bit parity
Device flags : Present Running
Interface flags: Point-To-Point SNMP-Traps
Link flags : Keepalives
Hold-times : Up 0 ms, Down 0 ms
CoS queues : 4 supported
Last flapped : 2004-05-21 15:23:34 UTC (00:05:00 ago)
Statistics last cleared: Never
Traffic statistics:
Input bytes : 0 0 bps
Output bytes : 0 0 bps
Input packets: 0 0 pps
Output packets: 0 0 pps
Input errors:
Errors: 0, Drops: 0, Framing errors: 0, Bucket drops: 0, Policed discards: 0,
L3 incompletes: 0, L2 channel errors: 0, L2 mismatch timeouts: 0,
HS link CRC errors: 0, SRAM errors: 0
Output errors:
Carrier transitions: 1, Errors: 0, Drops: 0, Aged packets: 0
DS3 alarms : None
SONET alarms : None
DS3 defects : None
SONET defects : None
DS3 media: Seconds Count State
AIS 0 0 OK
LOF 0 0 OK
LOS 0 0 OK
IDLE 0 0 OK
YELLOW 0 0 OK
BPV 0 0
EXZ 0 0
LCV 0 0
PCV 0 0
CCV 0 0
LES 0
PES 0
PSES 0
CES 0
CSES 0
SEFS 0
UAS 0
HDLC configuration:
Policing bucket: Disabled
Shaping bucket : Disabled
Giant threshold: 4484, Runt threshold: 3
Idle cycle flag: flags, Start end flag: shared
DSU configuration:
Compatibility mode: None, Scrambling: Disabled, Subrate: Disabled
FEAC loopback: Inactive, Response: Disabled, Count: 0
DS-3 BERT configuration:
BERT time period: 10 seconds, Elapsed: 0 seconds
Algorithm: 2^3 - 1, Pseudorandom (1), Induced error rate: 10e-0
Interface transmit queues:
B/W WRR Packets Bytes
Queue0 0 0
Transmitted: 0 0
Drops: 0 0
Errors: 0
Queue1 0 0
Transmitted: 0 0
Drops: 0 0
Errors: 0
Queue2 0 0
Transmitted: 0 0
Drops: 0 0
Errors: 0
Queue3 0 0
Transmitted: 0 0
Drops: 0 0
Errors: 0
SONET PHY: Seconds Count State
PLL Lock 0 0 OK
PHY Light 0 0 OK
SONET section:
BIP-B1 1 22
SEF 0 0 OK
LOS 0 0 OK
LOF 0 0 OK
ES-S 1
SES-S 0
SEFS-S 0
SONET line:
BIP-B2 1 307
REI-L 0 0
RDI-L 3 1 OK
AIS-L 0 0 OK
BERR-SF 0 0 OK
BERR-SD 0 0 OK
ES-L 1
SES-L 0
UAS-L 0
ES-LFE 3
SES-LFE 3
UAS-LFE 0
SONET path:
BIP-B3 1 35
REI-P 1 7
LOP-P 0 0 OK
AIS-P 0 0 OK
RDI-P 0 0 OK
UNEQ-P 0 0 OK
PLM-P 1 1 OK
ES-P 1
SES-P 0
UAS-P 0
ES-PFE 1
SES-PFE 0
UAS-PFE 0
Received SONET overhead:
F1 : 0x00, J0 : 0x00, K1 : 0x00, K2 : 0x00
S1 : 0x00, C2 : 0x04, C2(cmp) : 0x04, F2 : 0x00
Z3 : 0x00, Z4 : 0x00, S1(cmp) : 0x00
Transmitted SONET overhead:
F1 : 0x00, J0 : 0x01, K1 : 0x00, K2 : 0x00
S1 : 0x00, C2 : 0x04, F2 : 0x00, Z3 : 0x00
Z4 : 0x00
Received path trace: t3-0/1/0:0
74 33 2d 30 2f 31 2f 30 3a 30 00 00 00 00 0d 0a t3-0/1/0:0......
Transmitted path trace: t3-0/3/0:0
74 33 2d 30 2f 33 2f 30 3a 30 00 00 00 00 00 00 t3-0/3/0:0......
Packet Forwarding Engine configuration:
Destination slot: 0, PLP byte: 1 (0x00)
CoS transmit queue Bandwidth Buffer Priority Limit
% bps % bytes
0 best-effort 95 42499200 95 0 low none
3 network-control 5 2236800 5 0 low none
What It Means
The sample output shows that the physical link is up and there are no OC-12 alarms or defects. You should not see any OC-12 alarms. If there are SONET layer errors, see Investigate SONET Interfaces, for information on diagnosing SONET interface problems.